-
Siemens TPS3 15 - page 1
User Manual - USA TPS3 12 & TPS3 15 Surge Prot ective De vice ...
-
Siemens TPS3 15 - page 2
• Only qualified licensed electricians should install or ser vice SPDs • Hazardous voltages e xist within SPDs • SPDs should never be installed or serviced when energized • Use appropriat e safe ty precautions including Personal Pro tection Eq uipment • F ailure t o follo w these instructions can result in death, serious injury , and/or ...
-
Siemens TPS3 15 - page 3
T able of Contents F AILURE T O FOLLO W THESE INSTRUCTIONS COULD RESUL T IN DEA TH OR SERIOUS INJURY .............................. 2 Do Not Hi-Po t T est SPDs ............................................................................................................................................................................ 2 INTRODUCTION .. ...
-
Siemens TPS3 15 - page 4
Introduction Thank you for choosing Siemens TPS3 Surge Pro tective Device (SPD). This is a high quality , high energy surge suppres sor designed to prot ect sensitive equipment fr om damaging transient overvoltages. Proper installation is important to maximize per formance. Please follo w the steps outlined herein. This entire User Manual should be ...
-
Siemens TPS3 15 - page 5
2008 NEC Ar t 285 & UL 1449-3 SPD T ypes: T ypes 1, 2, 3, & 4 Based on Location within electrical distribution system (also coincides with ANSI/IEEE C62.41.2 - 2002 Categories C, B &A) Figure 1: SPD T ypes General Information Product F amily Outline TPS3 12 – Single Module in enclosure TPS3 15 – T wo Modules in enclosure Each is ava ...
-
Siemens TPS3 15 - page 6
TPS SERIES DESCRIPTION TPS3 12 Externally mount ed SPD, single module in enclosure, standard modes of pr ot ection TPS3 L12 Externally mount ed SPD, single module in enclosure, 10 modes of pr otection TPS3 15 Externally mount ed SPD, dual replaceable modules in enclosure, standard modes of pr ot ection TPS3 L15 Externally mount ed SPD, dual replace ...
-
Siemens TPS3 15 - page 7
Parallel Connection This is a Parallel connected SPD – not series connected. As outlined previousl y , an SPD ‘drains of f ’ excessiv e voltage fr om an electrical system. Because of parallel connection, installation of the SPD reasonably near the eq uipment to be pro tect ed is satisfactory. Tip: It is ver y important that wiring leads be co ...
-
Siemens TPS3 15 - page 8
T able 2: Weight & Dimensions TPS3 12 H/W/D (in./mm.) Weight Standar d Enclosure 12" x12" x 7.5" (305x305x191) 22 lbs (10 kg) Standar d Enclosure, 400 – 500kA with Opt. Disc. Switch 16" x 14" x 6" (496x356x152) 32 lbs (14.5 kg) 4X Non-Metallic 14" x 12" x 7" (356x305x178) 14 lbs (6.4 kg) 4X Non-Met ...
-
Siemens TPS3 15 - page 9
T erminals T erminals will accept 14 - 2 A WG conductor and are provided for line (phase), neutral (if used), and equipment safety ground connections. 8 A WG is the minimum recommended wire size because UL testing and evaluation was performed using 8 A WG. Wire Size and Installation T orque This is a parallel-connected SPD; it is not series-connect ...
-
Siemens TPS3 15 - page 10
Optional Flush Mount Installation Considerations The TPS3 12 and TPS3 15 are appro ximately 6” deep. The unit will not mount flush unless there is at least 6” of depth clearance. The TPS3 12 and TPS3 15 are not designed to mount flush on a typical 2 x 4 stud wall. Back Flange Mounting: Mount as close as possible to protect ed panel. Creat e a ...
-
Siemens TPS3 15 - page 11
PRE-PL AN INST ALL A TION TO ACC OMPLISH THE FOLLO WING: • Meet all National and Local codes (NEC® Ar ticle 285 addresses SPDs) • Mount SPD as close to panel or equipment as possible to keep leads short • Ensure leads are as shor t and straight as possible, including neutral and ground. Consider a break er position that is closest to the SPD ...
-
Siemens TPS3 15 - page 12
Figure 4: Electrical Dra wings Figur e 1 SPLIT 2 Hots, 1 Neu, 1 Grnd Hot (BLK) Hot (BLK) Neutral (WHT ) V V } } Ground (GRN ) Figur e 2 WYE 3 Hots, 1 Neu, 1 Grnd } Phase A (BLK) Phase B (BLK) Neutral (WHT ) Phase C (BLK) Ground (GRN ) A C N V B Figur e 3 HI-LEG DEL T A (B High) 3 Hots, (B HIGH), 1 Neu, 1 Grnd Phase A (BLK) Phase B (ORNG) Neutral (W ...
-
Siemens TPS3 15 - page 13
Phase A, B & C: Green LED indicators—one per phase. Green is good. Extinguished green LED indicates loss of prot ection. Every suppres sion element in this SPD is monitor ed. N-G suppres sion element monitoring is logic-connected t o Phase A. Ser vice LED (red): LED illuminates in the event of problems. This indicator is logic-connected to th ...
-
Siemens TPS3 15 - page 14
Dr y Contact Option T wo sets of Form C dr y contacts are included with the Dr y Cont act option. Dry Contacts change state during inoper ative conditions, including loss of power . Any status change can be monitored elsewhere via Dr y Contacts. A T erminal Block includes two sets of Normally Open (N.O.) and Normally Closed (N.C) cont acts. Both se ...
-
Siemens TPS3 15 - page 15
Display Replacement The display is field replaceable. Deenergize SPD, confirm with appropriat e measurement equipment and dischar ge internal capacitance to ground. Mark locations and carefully disconnect diagnostic cables, contacts, connecting conduct ors, etc. Unbolt display and r eplace. Reinstall in reverse. Not e that a sealing gask et betw ...
-
Siemens TPS3 15 - page 16
Siemens Industr y , Inc. Building T echnologies Division 5400 T riangle Parkway Norcr oss, GA 30092 888-333-3545 info.us@siemens.com 6.17.11.jb #8172 ...
Hai una domanda su Siemens TPS3 15?
Utilizza il modulo sottostante
Se non hai risolto il problema con Siemens TPS3 15 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Siemens TPS3 15 è probabile che voglia condividere il modo di risolverlo.