-
Harbor Freight Tools 44836 - page 1
ASSEMBL Y AND OPERA TING INFORMA TION 3491 Mission Oaks Blvd., Camarillo , CA 93011 Visit our W eb site at http://www .harborfreight.com Cop yright © 2001 by Harbor F reight T ools. All r ights reser ved. No por tion of this manual or any artwork contained herein may be reproduced in any shape or form without the e xpress written consent of Harbor ...
-
Harbor Freight Tools 44836 - page 2
1. KEEP WORK AREA CLEAN AND DR Y . Cluttered, damp or wet work areas invite injuries. 2. KEEP CHILDREN A W A Y FR OM W ORK AREA. Do not allow children to handle this product. 3. ST ORE IDLE EQUIPMENT . When not in use, tools and equipment should be stored in a dr y location to inhibit r ust. Alw a ys lock up tools and equipment and keep out of reac ...
-
Harbor Freight Tools 44836 - page 3
SKU 44836 P A GE 3 5. USE EYE, HEARING, AND BREA THING PRO TECTION. Wear ANSI appro v ed saf ety impact ey e glasses, ANSI appro v ed hearing protection, and ANSI approv ed dust mask or respirator when using this product. ANSI approv ed saf ety impact ey e glasses, hearing protection, and dust masks and respirators are available from Harbor F reigh ...
-
Harbor Freight Tools 44836 - page 4
sure this product is always plugged into a grounded 3-hole electrical receptacle with an appropriate breaker switch in-line. 2. MAKE SURE THE POWER SWITCH IS IN THE “OFF” POSITION BEFORE PLUGGING IN THE POWER CORD. 3. DO NO T ABUSE THE PO WER CORD . Do not use the cord to pull the 3-prong plug from a power outlet. Keep cord away from heat, oil, ...
-
Harbor Freight Tools 44836 - page 5
SKU 44836 P A GE 5 10. CAUTION: Some woods contain preservatives such as copper chromium arsenate (CCA) which can be toxic. When drilling these materials extra care should be taken to avoid inhalation and minimize skin contact. 11. ALLO W THE DRILL BIT T O SPIN UP T O FULL SPEED BEFORE DRILLING INT O THE WORKPIECE. When tur ning off the Dr ill Pres ...
-
Harbor Freight Tools 44836 - page 6
SKU 44836 P A GE 6 3. T o attac h the Head Assemb l y (par t #1B) to the Column (par t #1A) , loosen the Hex Screws (part #13B) to ensure the Screws do not protrude internally in the Column (par t #1A), as this would pre v ent the Head Assembly from sliding do wnward fully onto the Column. With assistance raise the Head Assemb ly and slide it fully ...
-
Harbor Freight Tools 44836 - page 7
Bolts of appropriate length, W ashers and Locknuts (not pro vided). T o Install/Reposition The Drive Belts: 1. The Drill Press features 12 speed selections from which to choose. 2. The two V -Belts (par ts #21C, 26C), when positioned on the three Pulle ys (parts #3C, 28C, 19C), will determine the speed at which the Drill Press will run. (See Assemb ...
-
Harbor Freight Tools 44836 - page 8
SKU 44836 P A GE 8 T o Obtain The Pr oper Cutting Speeds: 1. Factors which determine the best speed to use in the Drill Press are: A . The kind of material being dr illed. B . The siz e of the hole. C . The quality of cut desired. 2. Generally , in soft mater ial the speed should be higher than f or hard materials. The following guide indicates the ...
-
Harbor Freight Tools 44836 - page 9
T o Adjust The T ab le: 1. The T ab le (par t #9A) may be adjusted in 4 directions . 2. T o raise or lower the T ab le , release the T ab le Clamp (par t #11A), and tur n the Crank (par t #6A) clockwise to raise the T able and countercloc kwise to lower the T ab le . When the desired height of the T ab le has been reached, secure the T ab le in pla ...
-
Harbor Freight Tools 44836 - page 10
SKU 44836 P A GE 10 5. The Drill Press is now set to drill holes to your pre-determined depth, provided the surf ace of the workpiece is flat and le v el. Y ou ma y also dr ill a series of holes to the same depth. T o Operate The Drill Press: 1. Before starting the Drill Press, make sure all adjustments are properly made and all of the guards are i ...
-
Harbor Freight Tools 44836 - page 11
SKU 44836 P A GE 11 5. Set the depth of drill bit travel so that the drill bit cannot come into contact with the T ab le (par t #9A), or align the T ab le so that the hole in its center is in line with the drill bit. 6. The Drill Press is now ready to operate. CLEANING, INSPECTION, AND MAINTENANCE 1. Caution : Alwa ys disconnect the Dr ill Press fr ...
-
Harbor Freight Tools 44836 - page 12
SKU 44836 P A GE 12 FIGURE G ...
-
Harbor Freight Tools 44836 - page 13
SKU 44836 P A GE 13 PLEASE READ THE FOLLO WING CAREFULL Y THE MANUF A CTURER AND/OR DISTRIBUT OR HAS PR O VIDED THE P AR TS DIA- GRAM IN THIS MANU AL AS A REFERENCE T OOL ONL Y . NEITHER THE MANUF A C- TURER NOR DISTRIBUT OR MAKES ANY REPRESENT A TION OR W ARRANTY OF ANY KIND T O THE BUYER THA T HE OR SHE IS QU ALIFIED T O MAKE ANY RE- P AIRS T O T ...
-
Harbor Freight Tools 44836 - page 14
DESCRIPTION Head w/P ointer & T r im Motor Hex Nut M8 W asher 8 Cord - Motor Hex Nut M10 Lockwasher 10 Bracket - Motor Hex Head Screw M8 x 1.25-20 Support - Motor Bracket Roll Pin 6 x 16 Knob - Motor Adjusting Hex Screw Socket Set M8 x 1.25-8 Lock - Depth Screw Ring - Depth Stop w/Scale Knob Rod Hub - Pinion Pin - Stop Connector - Wire Lockwash ...
-
Harbor Freight Tools 44836 - page 15
SKU 44836 P A GE 15 ASSEMBL Y DIA GRAM B NOTE: Some parts are listed and shown for illustra- tion pur poses only , and are not available individually as replace- ment parts. ...
-
Harbor Freight Tools 44836 - page 16
P AR TS LIST/ASSEMBL Y DIA GRAM C SKU 44836 P A GE 16 NOTE: Some parts are listed and shown for illustration pur poses only , and are not av ailable individually as replacement parts. DESCRIPTION Knob Pan Head Screw M5 x 0.8-12 Pulley - Motor Screw - Hex Socket Set Guard - Pulley w/Labels Bearing - Ball 12mm Shaft - Spindle Chuck Key Chuck T ube Qu ...
Hai una domanda su Harbor Freight Tools 44836?
Utilizza il modulo sottostante
Se non hai risolto il problema con Harbor Freight Tools 44836 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Harbor Freight Tools 44836 è probabile che voglia condividere il modo di risolverlo.