-
Tanaka ECV-4501 - page 1
Owner’ Owner’ Owner’ Owner’ Owner’ s Man s Man s Man s Man s Man ual ual ual ual ual Model Numbers: ECV-4501 ECV-4501 ECV-4501 ECV-4501 ECV-4501 CHAINSAW CHAINSAW CHAINSAW CHAINSAW CHAINSAW P/N 29768 Date 05-04-01 Supplier T o The Outdoor P ower Equipment Industry ISM, Inc . • 1028 4 th Str eet SW • Auburn, WA 98001 • Phone: (253) 3 ...
-
Tanaka ECV-4501 - page 2
www.tanakapowerequipment.com 1 custsvc@tanaka-ism.com Owner’s Manual ECV-4501 Before using this unit: • Read the operator’s manual carefully. • Check that the cutting equipment is correctly assembled and adjusted. • Start the unit and check the carburetor adjustment. See “Maintenance”. One-handed usage not permitted. While cutting, ho ...
-
Tanaka ECV-4501 - page 3
www.tanakapowerequipment.com 2 custsvc@tanaka-ism.com Owner’s Manual ECV-4501 ...
-
Tanaka ECV-4501 - page 4
www.tanakapowerequipment.com 3 custsvc@tanaka-ism.com Owner’s Manual ECV-4501 2. Warnings and safety instructions Operator Safety • Always wear a sa fety face shield or goggles. • Gloves should be used when sharpening chain. • Always wear safety protectiv e equipment such as jacket, trousers, gloves, boots with steel toe-ca ps and non-slip ...
-
Tanaka ECV-4501 - page 5
www.tanakapowerequipment.com 4 custsvc@tanaka-ism.com Owner’s Manual ECV-4501 3. Assembly procedures WARNING! Never try to start engine without side case securely fastened. ** Install the provided spiked bumper (1) to the unit with the two screws. (Fig. 1-0) 1 . Remove the side case by unscrewing two guide bar clamp nut s, and install the guide b ...
-
Tanaka ECV-4501 - page 6
www.tanakapowerequipment.com 5 custsvc@tanaka-ism.com Owner’s Manual ECV-4501 4. Operating procedures Fuel (Fig. 2-1) WARNING! The chainsaw is equipped with a two-stroke engine. Alwa ys run the engine on fuel, which is mixed with oil. Provide good ventilation, when fueling or handling fuel. Fuel • Always use branded 89 octane unleaded gasoline. ...
-
Tanaka ECV-4501 - page 7
www.tanakapowerequipment.com 6 custsvc@tanaka-ism.com Owner’s Manual ECV-4501 WARNING! When the engine starts with the throttle lock engaged, the engine speed is high enough to make the chain rotate. Starting Warm Engine 1. Set ignition switch to ON position. Pr ess decompression valve and pull recoil starter. 2. If engine does not start easily, ...
-
Tanaka ECV-4501 - page 8
www.tanakapowerequipment.com 7 custsvc@tanaka-ism.com Owner’s Manual ECV-4501 Chain brake operation (Optional) (Fig. 2-5) Chain brake (1) is designed to activate in an emergency such as kick-back action. Please check to verify that it works properly before use. Application of brake is made by moving the front guard towa rds the bar. During the ch ...
-
Tanaka ECV-4501 - page 9
www.tanakapowerequipment.com 8 custsvc@tanaka-ism.com Owner’s Manual ECV-4501 WARNING! Never use the saw with only one hand. You cannot control the saw properly and you may lose control and injure yourself severely. Keep the saw body close to your body to improve control and reduce strain. When cutting with the bottom part of the chain the reacti ...
-
Tanaka ECV-4501 - page 10
www.tanakapowerequipment.com 9 custsvc@tanaka-ism.com Owner’s Manual ECV-4501 WARNING! Always observe the general conditions of the tree. Look for decay and rot in the trunk which will make it more likely to snap and start to fall before you expect it. Look for dry branches, which may break and hit you when you are working. Always keep animals an ...
-
Tanaka ECV-4501 - page 11
www.tanakapowerequipment.com 10 custsvc@tanaka-ism.com Owner’s Manual ECV-4501 LIMBING Limbing is removing the branches from a felled tree. WARNING! A majority of kickback accidents occur during limbing. Do not use the nose of the guide bar. Be extremely ca utious and avoid contacting the log, other limbs or objects with the nose of the guide bar ...
-
Tanaka ECV-4501 - page 12
www.tanakapowerequipment.com 11 custsvc@tanaka-ism.com Owner’s Manual ECV-4501 THICK LOG, LARGER THAN GUIDE BAR LENGTH Begin by cutting on the opposite side of the log. Pull the saw towards you followed pre vious procedure. (Fig. 2-7J) If the log is lying on the ground make a boring cut to avoid cutting into the ground. Finish with a bottom cut. ...
-
Tanaka ECV-4501 - page 13
www.tanakapowerequipment.com 12 custsvc@tanaka-ism.com Owner’s Manual ECV-4501 In the carburetor, fuel is mixed with air. When the engine is test run at the factory, the carburetor is basically adjusted. A further adjustment may be required, accord ing to climate and altitude. The carburetor has one adjustment possibility: T = Idle speed adjustme ...
-
Tanaka ECV-4501 - page 14
www.tanakapowerequipment.com 13 custsvc@tanaka-ism.com Owner’s Manual ECV-4501 Air filter (Fig. 3-2) The air filter (1) must be cleaned from dust and dirt in order to avoid: • Carburetor malfunctions. • Starting problems. • Engine power reduction. • Unnecessary wear on the engine parts. • Abnormal fuel consumption. Clean the air filter ...
-
Tanaka ECV-4501 - page 15
www.tanakapowerequipment.com 14 custsvc@tanaka-ism.com Owner’s Manual ECV-4501 Guide bar (Fig. 3-5) Before using the machine, clean the groove and oiler port (1) in the bar with the special gauge offered as an optional accessory. Oiler port (Fig. 3-4) Clean the chain Oiler port (1) whenever possible. Side case (Fig. 3-6) Always keep the side case ...
-
Tanaka ECV-4501 - page 16
www.tanakapowerequipment.com 15 custsvc@tanaka-ism.com Owner’s Manual ECV-4501 Decompression valve (Fig. 3-11) After extended period of use decompression valve may not close or come out due to the built up carbon inside of the valve mounting hole (1). To remove the carbon, take the following steps. 1 . Remove air filter cover, cylinder cover, spa ...
-
Tanaka ECV-4501 - page 17
www.tanakapowerequipment.com 16 custsvc@tanaka-ism.com Owner’s Manual ECV-4501 LOWERING DEPTH GAUGES WITH A FILE 1) If you sharpen your cutters with a file holder, check and lower the depth. 2) Check depth gauges every third sharpening. 3) Place depth gauge tool on cutter. If depth gauge projec ts, file it level with the top of the tool. Always f ...
-
Tanaka ECV-4501 - page 18
www.tanakapowerequipment.com 17 custsvc@tanaka-ism.com Owner’s Manual ECV-4501 Maintenance schedule Below you will find some general maintenance instructions. For further information please contact your service dealer. Daily maintenance • Clean the exterior of the unit. • Clean the chain oil filter port. • Clean the groove and oil filter po ...
-
Tanaka ECV-4501 - page 19
www.tanakapowerequipment.com 18 custsvc@tanaka-ism.com Owner’s Manual ECV-4501 6. Specifications ...
-
Tanaka ECV-4501 - page 20
www.tanakapowerequipment.com 19 custsvc@tanaka-ism.com Owner’s Manual ECV-4501 Declaration of conformity Declaration de conformit6 Dichiarazione di conformita Konformitiitserkliirung Declaraci6n de conformidad Konformitetsdeklaration Tanaka Kogyo Co., Ltd., 3-4-29 Tsuda num a, Narashino, Chiba, Japan ECV-4501 Declare under our sole responsibility ...
-
Tanaka ECV-4501 - page 21
www.tanakapowerequipment.com 20 custsvc@tanaka-ism.com Owner’s Manual ECV-4501 IMPORTANT NOTICE THIS INFORMATION IS FOR THE US AND CANADIAN MARKETS ONLY. Only use replacement bars and chains specified by th e manufacturer other equivalent.(See the chart below) Bar & Chain USA and Bar & Chain CANADA LOW KICKBACK BAR AND CHAIN COMBINATIONS ...
Hai una domanda su Tanaka ECV-4501?
Utilizza il modulo sottostante
Se non hai risolto il problema con Tanaka ECV-4501 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Tanaka ECV-4501 è probabile che voglia condividere il modo di risolverlo.