Italiano dropdown-ico

Manuale per l’uso Sanyo VCC-5974

31 pagine 0.43 mb
Scarica

Vai alla pagina of 31

Summary
  • Sanyo VCC-5974 - page 1

    INSTRUCTION MANUAL COLOR CCD Camera VCC-5974 About this manual • Before inst alling and usin g th e came ra, pl ease read t his manu al car efull y. Be sure to keep it handy for later reference. L53P 4/U S GB 19 98 , 3, 11 ...

  • Sanyo VCC-5974 - page 2

    SANYO INDUSTRIAL VIDEO COLOR VIDEO CAMERA LIMITED WARRANTY OBLIGATIONS In order to obtain warranty service, the product must be delivered to and picked up from an Authorized Sanyo Service Center at the user’s expense, unless specifically stated otherwise in this warranty. The names and addresses of Authorized Sanyo Service Centers may be obtained ...

  • Sanyo VCC-5974 - page 3

    Depending on the conditions of use, installation and environment, please be sure to make the appropriate settings and adjustments. If you need help with installation and/or settings, please consult your dealer. CONTENTS INFORMATION TO USER .................................. 2 PRECAUTIONS ................................................... 3 PARTS N ...

  • Sanyo VCC-5974 - page 4

    Safety Guard THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT OPERATING AND MAINTENANCE INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THIS UNIT. WARNING: TO PREVENT THE RISK OF FIRE OR ELECTRIC SHOCK , DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. This installation should be made by a qualified service person and should conform to all local codes. ...

  • Sanyo VCC-5974 - page 5

    PRECAUTIONS In case of problem Do not use the camera if smoke or a strange odour comes from the unit, or if it seems not to function correctly. Disconnect the power cord immediately, and consult your dealer (or a Sanyo Authorized Service Centre). Do not open or modify Do not open the cabinet, as it may be dangerous and cause damage to the unit. For ...

  • Sanyo VCC-5974 - page 6

    PARTS NAMES 1 Lens iris output connector (4 pin) This 4-pin connector is used to send the DC control signal and power supply to an auto-iris type lens. 2 Auto white balance push lock button (AWB LOCK) 3 Menu setting button (SET) Connect the camera to the monitor, then press the SET button for about 3 seconds to display the on-screen menu. 4 Cursor ...

  • Sanyo VCC-5974 - page 7

    PARTS NAMES 9 Camera setup section (under the cover) This unit factory settings are as indicated below. These settings are for when using a 1/3 inch CS mount DC (without EE internal amplifier) type lens. However, if due to installation conditions or environment the settings may need to be modified for best results (see " SETTINGS "). To a ...

  • Sanyo VCC-5974 - page 8

    F Video output connector (VIDEO OUT: BNC type) Connect this connector to a device such as a VCR or monitor with a VIDEO IN connector. G External sync composite video signal input connector (VBS IN: BNC type) Connect to this connector the synchronizing signal output from a synchronizing signal device or the composite signal of a video distributor. H ...

  • Sanyo VCC-5974 - page 9

    PARTS NAMES 1 1 3 LOCK 2 ADJ. Flange-back adjustment If the pick-up surface is not correctly positioned with relation to the lens focal point, the picture will be out of focus (in particular when using auto-iris power zoom lenses, sold separately). If that is the case, adjust the flange-back position as described below. 1 Using a + screwdriver, loo ...

  • Sanyo VCC-5974 - page 10

    MOUNTING THE LENS Installation of a VIDEO type auto-iris lens (sold separately) A 1/2 or 2/3 inch C mount type lens with EE amplifier circuit that uses the video signal and a DC power source. 1 Remove the lens mount cap. 2 Attach the supplied C mount adaptor (A) to the auto-iris lens (B) , then install the assembly on the camera. 3 Connect the lens ...

  • Sanyo VCC-5974 - page 11

    MOUNTING THE LENS Compatible auto-iris lenses 1/3 inch Sanyo DC type lens 1/2 or 2/3 inch VIDEO type lens VCL-CS8LY: Standard angle, f= 8 mm Standard angle, f= 9 mm VCL-CS4LY: Wide angle, f= 4 mm Telephoto angle, f= 12 mm VCL-CS2LY: Ultra-wide angle, f= 2.8 mm More telephoto angle, f= 16 mm If using a VIDEO type auto-iris lens • Set the ALC and L ...

  • Sanyo VCC-5974 - page 12

    SETTINGS The illustration shows the factory default settings for the switches in the camera setup section. Depending on the camera installation location and conditions of use, it may be necessary to select other settings, without having to make adjustments. The selected settings can be confirmed using the on-screen menu. If adjustments are required ...

  • Sanyo VCC-5974 - page 13

    SETTINGS Automatic Gain Control (AGC) setting The automatic gain control can be turned ON or OFF using the AGC ON/OFF switch (6) in the camera setup section. ON : Auto gain control function on (setting used under normal conditions) (see page 23 ). GAMMA : ON (0.45), OFF (1) AGC GAIN : NORMAL (30 dB), HIGH (36 dB) OFF : Fixed gain Note: When the AGC ...

  • Sanyo VCC-5974 - page 14

    ON OFF AI EI WINDOW WEIGHTING W0 1 W1 1 W2 3 W3 3 W4(FIX) 15 PRESET OFF MENU END END W0=1 W2=10 W4=15 W3=10 W1=5 W2=0 W4=15 W3=0 W1=15 W0=0 Fig. 1 Fig. 2 Fig. 3 Backlight compensation (BLC) setting The backlight compensation ON/OFF is set using the BLC ON/OFF switch (9) in the camera setup section. ON : Default setting, backlight compensation funct ...

  • Sanyo VCC-5974 - page 15

    USING THE ON-SCREEN MENUS MENU FOR ADJUSTMENT SYNC INT IRIS AI BLC ON WHITE BALANCE ATW AGC ON SHUTTER 60 WRITE PROTECT ON NEXT PAGE END MENU FOR ADJUSTMENT CAMERA ID OFF APERTURE WRITE PROTECT ON PREVIOUS PAGE END (Menu 1) (Menu 2) 5 3 2 46 8 7 SET INT SET CURSOR SET CURSOR CURSOR SET CURSOR (or j ) 1 To display the menu Press the SET button for a ...

  • Sanyo VCC-5974 - page 16

    ADJUSTMENTS To enter settings or adjustments for the camera it must be connected to a monitor. The settings and adjustments are made by ways of on-screen displays. Concerning the WRITE PROTECT function In order to protect the settings and adjustments the WRITE PROTECT function is set to ON . If it is necessary to enter new settings or adjustments, ...

  • Sanyo VCC-5974 - page 17

    ADJUSTMENTS 1. SYNC 1-1. V sync phase adjustment When using a camera switcher to connect 2 cameras or more to one monitor, there may be a vertical roll of the images when switched. In such a case, set as described below. 1 Set the SYNC switch (4) to L-L . The on-screen setting will automatically switch to L-L . Press the CURSOR ( j or l ) button to ...

  • Sanyo VCC-5974 - page 18

    1-2. VBS phase adjustment 1 Conn ec t a VB S signal source to the VBS IN connector on the camera. The on- scre en s etting will automa tica lly s witc h to VBS . Pre ss the CURSOR ( j or l ) b ut ton t o s elect the o n-s creen VBS sett ing (get i t f lashi ng) , t hen pre ss th e SET but ton. The ad justm ent sub-m enu “ ADJ USTME NT FO R VB S ? ...

  • Sanyo VCC-5974 - page 19

    ADJUSTMENTS 2. IRIS 2-1. Auto-iris level adjustment 1 Set the IRIS switch (10) to AI . The on-screen setting will automatically switch to AI . Press the CURSOR ( j or l ) button to select the on-screen AI setting (get it flashing), then press the SET button. The adjustment sub-menu “ ADJUSTMENT FOR AI ” will be displayed. 2 Press the CURSOR ( d ...

  • Sanyo VCC-5974 - page 20

    ADJUSTMENT FOR BLC BLC MODE PRESET 1 ADJUSTMENT FOR BLC (SIZE) ADJUSTMENT FOR BLC (POSITION) WINDOW WEIGHTING W0 1 W1 1 W2 3 W3 3 W4(FIX) 15 PRESET OFF END MENU 3. BLC 3-1. Setting the light measuring area characteristics (size, position and distribution) for the MANUAL 1 setting 1 Set the BLC switch (9) to ON . Th e on-s creen sett ing for BLC wi ...

  • Sanyo VCC-5974 - page 21

    ADJUSTMENTS 5 Press the CURSOR ( j or l ) button to select the desired window (get its value flashing), then press the CURSOR ( d or c ) button to set the desired value (maximum 15) for each of the 4 windows 0, 1, 2 and 3. Example: W0 : 5, W1 : 5, W2 : 10 and W3 : 10 Note: When an adjustment is made, the PRESET setting will automatically switch to ...

  • Sanyo VCC-5974 - page 22

    3-2. BLC level adjustment for the PRESET 1 setting 1 Set the BLC switch (9) to ON . The on-screen setting for BLC will automatically switch to ON . Press the CURSOR ( j or l ) button to select the on-screen ON setting (get it flashing), then press the SET button. The adjustment sub-menu “ ADJUSTMENT FOR BLC ” will be displayed. 2 Press the CURS ...

  • Sanyo VCC-5974 - page 23

    ADJUSTMENTS 4. WHITE BALANCE 4-1. PRESET MODE 2 (indoors, fluorescent lighting) setting adjustment 1 Set the WB switches to the PRESET mode (switch 7 to OFF and switch 8 to ON ). The on-screen setting for WHITE BALANCE will automatically switch to PRESET. Press the CURSOR ( j or l ) button to select the on-screen PRESET setting (get it flashing), t ...

  • Sanyo VCC-5974 - page 24

    4-2. MANUAL setting adjustment 1 Set the WB switches to the MANUAL mode (both switches 7 and 8 to OFF ). ...

  • Sanyo VCC-5974 - page 25

    ADJUSTMENTS 5. AGC 1 Set the AGC switch (6) to ON . The on-screen setting for AGC will automatically switch to ON . Press the CURSOR ( j or l ) button to select the on-screen ON setting (get it flashing), then press the SET button. The adjustment sub-menu will be displayed. 2 Setting the GAMMA Press the CURSOR ( d or c ) button to select ON or OFF ...

  • Sanyo VCC-5974 - page 26

    6. CAMERA ID 1 Press the CURSOR ( j or l ) button to select NEXT PAGE (get it flashing), then press the SET button. The second page of the “ MENU FOR ADJUSTMENT ” will be displayed. (Refer to page 13 .) 2 With the CAMERA ID ON setting flashing, press the SET button. The sub-menu “ CAMERA ID SETTING ” will be displayed. The camera ID will be ...

  • Sanyo VCC-5974 - page 27

    ADJUSTMENTS 7. APERTURE 1 Press the CURSOR ( j or l ) button to select NEXT PAGE (get it flashing), then press the SET button. The second page of the “ MENU FOR ADJUSTMENT ” will be displayed. 2 Press the CURSOR ( j or l ) button to select APERTURE (get it flashing), then press the SET button. The adjustment sub-menu “ ADJUSTMENT FOR APERTURE ...

  • Sanyo VCC-5974 - page 28

    TROUBLESHOOTING Before taking the camera for repairs, please check below to make sure that the camera is used correctly. If it still does not perform correctly, please consult your dealer or a Sanyo Authorized Service Centre. No picture on the monitor screen • Is the power turned on to all connected devices? Is the voltage correct? • Are all th ...

  • Sanyo VCC-5974 - page 29

    MENU FOR ADJUSTMENT CAMERA ID ON APERTURE WRITE PROTECT ON PREVIOUS PAGE END VBS VS L-L EI OFF ADJUSTMENT FOR AI (IRIS LEVEL) o------z------p 23 LOCK PRESET MANUAL 100 250 500 1000 2000 4000 10000 MENU FOR ADJUSTMENT SYNC INT IRIS AI BLC ON WHITE BALANCE ATW AGC ON SHUTTER 60 WRITE PROTECT ON NEXT PAGE END b SYNC ADJUSTMENT ☞ SW4: LL/INT INT (ins ...

  • Sanyo VCC-5974 - page 30

    ADJUSTMENT FOR VBS (PHASE) H o------z------p 280 SC o------z------p 90 ADJUSTMENT FOR VS (H SYNC PHASE) o------z------p 280 ADJUSTMENT FOR L-L (V SYNC PHASE) o------z------p 518 ADJUSTMENT FOR BLC BLC MODE PRESET1 BLC LEVEL PRESET2 MANUAL1 MANUAL2 WINDOW WEIGHTING W0 1 W1 1 W2 3 W3 3 W4(FIX) 15 MODE2 MODE3 MODE2 MODE3 ADJUSTMENT FOR BLC (BLC LEVEL) ...

  • Sanyo VCC-5974 - page 31

    SPECIFICATIONS Camera: Scaning system : NTSC standard TV system (525 TV lines, 30 frames/sec.) Interlace : PLL 2:1 interlace Image device : 1/3 inch solid state image device CCD Picture elements : 811 (H) x 508 (V) Effective picture elements : 768 (H) x 494 (V) Synchronizing system : Internal sync, Line lock manually switchable/External sync Extern ...

Fabbricante Sanyo Categoria Security Camera

I documenti che otteniamo dal fabbricante del dispositivoSanyo VCC-5974 possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Sanyo
- manuali per l’uso VCC-5974
- schede prodotto Sanyo
- opuscoli
- o etichette energetiche Sanyo VCC-5974
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Sanyo VCC-5974.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Sanyo VCC-5974, manuali di manutenzione, brevi manuali o manuali utente Sanyo VCC-5974. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Sanyo VCC-5974.

Manuali per l’uso simili

Manuale completo del dispositivo Sanyo VCC-5974, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Sanyo VCC-5974 dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Sanyo VCC-5974.

Il manuale per l’uso completo Sanyo, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Sanyo VCC-5974 - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Sanyo VCC-5974, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Sanyo VCC-5974 che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Sanyo VCC-5974 - che ci dovrebbe aiutare nei primi passi durante l'uso Sanyo VCC-5974
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Sanyo VCC-5974
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Sanyo VCC-5974 in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Sanyo VCC-5974?

Utilizza il modulo sottostante

Se non hai risolto il problema con Sanyo VCC-5974 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Sanyo VCC-5974 è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)