-
Chamberlain 3575 3 HP - page 1
The Chamberlain Group, Inc. 845 Larch Avenue Elmhurst, Illinois 60126-1 196 www .liftmaster .com GARAGE DOOR OPENER Models 3575 3/4 HP 3575-267D 3/4 HP 3575K 3/4 HP For Residential Use Only Owner’s Manual ■ Please read this manual and the enclosed safety materials carefully! ■ Fasten the manual near the garage door after installation. ■ The ...
-
Chamberlain 3575 3 HP - page 2
2 Introduction 2-5 Safety symbol and signal word review ........................2 Preparing your garage door ........................................3 T ools needed ...............................................................3 Planning .....................................................................4 Carton inventory ....................... ...
-
Chamberlain 3575 3 HP - page 3
3 T o prevent damage to garage door and opener: • AL WA YS disable locks BEFORE installing and operating the opener . • ONL Y operate garage door opener at 120V , 60 Hz to avoid malfunction and damage. T o prevent possible SERIOUS INJURY OR DEA TH: • AL WA YS call a trained door systems technician if garage door binds, sticks, or is out of ba ...
-
Chamberlain 3575 3 HP - page 4
FINISHED CEILING Support bracket & fastening hardware is required. See page 12. Slack in chain tension is normal when garage door is closed. Safety Reversing Sensor Header W all Access Door Safety Reversing Sensor Gap between floor and bottom of door must not exceed 1/4" (6 mm) W all- mounted Door Control Motor Unit ONE-PIECE DOOR WITHOUT ...
-
Chamberlain 3575 3 HP - page 5
5 Y our garage door opener is packaged in two cartons which contain the motor unit and all parts illustrated below . Accessories will depend on the model purchased. If anything is missing, carefully check the packing material. Parts may be stuck in the foam. Hardware for installation is also listed below . Carton Inventor y Straight Door Arm Sectio ...
-
Chamberlain 3575 3 HP - page 6
W ashered Bolt 5/16"-1 8 x1/2" Styrofoam T -rail Hole Lock Nu t 6 ASSEMBL Y STEP 1 Attach the T -Rail to the Motor Unit T o avoid installation difficulties, do not run the garage door opener until instructed to do so. • Remove the bolt and lock nut from the top of the motor unit. • Place rail onto the bolt mounted on the motor unit an ...
-
Chamberlain 3575 3 HP - page 7
7 Lock W asher T o Tighten Outer Nut Inner Nut T rolley Chain Base of Rail 1/2" (13 mm) T o Tighten Inner Nut Outer Nut Mid Length of Rail INST ALLA TION ASSEMBL Y STEP 3 Tighten the Chain • Spin the inner nut and lock washer down the trolley threaded shaft, away from the trolley . • T o tighten the chain, turn outer nut in the direction s ...
-
Chamberlain 3575 3 HP - page 8
8 INST ALLA TION STEP 1 Determine the Header Bracket Location Installation procedures vary according to garage door types. Follow the instructions which apply to your door . 1. Close the door and mark the inside vertical centerline of the garage door . 2. Extend the line onto the header wall above the door . Y ou can fasten the header bracket withi ...
-
Chamberlain 3575 3 HP - page 9
9 INST ALLA TION STEP 2 Install the Header Bracket Y ou can attach the header bracket either to the wall above the garage door , or to the ceiling. Follow the instructions which will work best for your particular requirements. Do not install the header bracket over drywall. If installing into masonry , use concrete anchors (not provided). W ALL HEA ...
-
Chamberlain 3575 3 HP - page 10
10 Clevis Pin 5/16"x2-3/4" Ring Fastener INST ALLA TION STEP 3 Attach the Rail to the Header Bracket • Position the opener on the garage floor below the header bracket. Use packing material as a protective base. NOTE: If the door spring is in the way you’ll need help. Have someone hold the opener securely on a temporary support to all ...
-
Chamberlain 3575 3 HP - page 11
11 ONE-PIECE DOOR WITHOUT TRACK A 2x4 on its side is convenient for setting an ideal door-to-rail distance. • Remove foam packaging. • Raise the opener onto a stepladder . Y ou will need help at this point if the ladder is not tall enough. • Open the door all the way and place a 2x4 on its side on the top section of the door beneath the rail. ...
-
Chamberlain 3575 3 HP - page 12
Meas u re Distance Lag Scre w s 5/16"-18x1-7/8" Str u ct u ral S u pports Bracket (Not Pro v ided) Lag Scre w s 5/16"-18x1-7/8" (Not Pro v ided) Bolt 5/16"-18x7/8" Lock W asher 5/16" N u t 5/16"-18 FINISHED CEILING Hidden S u pport Bolt 5/16"-18x7/8" Lock W asher 5/16" N u t 5/16"-18 Bolt ...
-
Chamberlain 3575 3 HP - page 13
KG 1 3 9 7 5 KG 1 3 9 7 5 13 INST ALLA TION STEP 6 Install the Door Control Locate door control within sight of the door at a minimum height of 5 feet (1.5 m) where small children cannot reach, and away from moving parts of the door and door hardware. The installation surface must be smooth and flat. If installing into drywall (Figure 1), drill 5/3 ...
-
Chamberlain 3575 3 HP - page 14
14 INST ALLA TION STEP 7 Install the Light • Press the release tabs on both sides of lens. Gently rotate lens back and downward until the lens hinge is in the fully open position. Do not remove the lens. • Install up to a 100 watt maximum light bulb in each socket. The light will turn ON and remain lit for approximately 4-1/2 minutes when power ...
-
Chamberlain 3575 3 HP - page 15
15 INST ALLA TION STEP 9 Electrical Requirements T o avoid installation difficulties, do not run the opener at this time. T o reduce the risk of electric shock, your garage door opener has a grounding type plug with a third grounding pin. This plug will only fit into a grounding type outlet. If the plug doesn’t fit into the outlet you have, conta ...
-
Chamberlain 3575 3 HP - page 16
16 Invisible Light Beam Protection Area Sensor Beam 6" (15 cm) max. above floor Sensor Beam 6" (15 cm) max. above floor Facing the door from inside the garage INST ALLA TION STEP 10 Install The Protector System ® The safety reversing sensor must be connected and aligned correctly before the garage door opener will move in the down direct ...
-
Chamberlain 3575 3 HP - page 17
17 DOOR TRACK MOUNT (RIGHT SIDE) Indicator Light Lens Lip Sensor Bracket Door Track FLOOR MOUNT (RIGHT SIDE) WALL MOUNT (RIGHT SIDE) Indicator Light Sensor Bracket Lens Extension Bracket (See Accessories) Inside G arage W all (Provided with Extension Bracket) (Provided with Extension Bracket) Figure 1 Figure 2 Figure 3 Figure 4 WALL MOUNT (RIGHT SI ...
-
Chamberlain 3575 3 HP - page 18
In v isi b le Light Beam Protection Area Sensor Sensor Connect Wire to Opener Q u ick-Connect T erminals Bell Wire Bell Wire Finished Ceilin g Q u ick-Connect T erminals 3. Insert into appropriate terminals 1. Strip w ire 7/16" (1 1 mm) 2. T w ist like colored w ires together 7/16" (1 1mm) Red Grey White 1 8 Carriage Bolt 1/4"-20x1/2 ...
-
Chamberlain 3575 3 HP - page 19
19 Fiberglass, aluminum or lightweight steel garage doors WILL REQUIRE reinforcement BEFORE installation of door bracket. Contact your door manufacturer for reinforcement kit. WARN ING CAUTION WARN ING WARN ING INST ALLA TION STEP 11 Fasten the Door Bracket Follow instructions which apply to your door type as illustrated below or on the following p ...
-
Chamberlain 3575 3 HP - page 20
20 Header W all Vertical Centerline of Garage Door Finished Ceiling Optional Placement of Door Bracket Header Bracket Door Bracket 2x4 Support For a door with no exposed framing, or for the optional installation, use lag screws 5/16"x1-1/2" ( N ot Provided) to fasten door bracket. MET AL DOOR Top of Door (Inside Garage) Door Bracket Optio ...
-
Chamberlain 3575 3 HP - page 21
21 INST ALLA TION STEP 12 Connect Door Arm to T rolley Follow instructions which apply to your door type as illustrated below and on the following page. SECTIONAL DOORS ONL Y • Make sure garage door is fully closed. Pull the emergency release handle to disconnect the outer trolley from the inner trolley . Slide the outer trolley back (away from t ...
-
Chamberlain 3575 3 HP - page 22
22 ALL ONE-PIECE DOORS 1. Assemble the door arm, Figure 4: • Fasten the straight and curved door arm sections together to the longest possible length (with a 2 or 3 hole overlap). • With the door closed, connect the straight door arm section to the door bracket with the 5/16"x1-1/4" clevis pin. • Secure with a ring fastener . 2. Adj ...
-
Chamberlain 3575 3 HP - page 23
23 Without a properly installed safety reversal system, persons (particularly small children) could be SERIOUSL Y INJURED or KILLED by a closing garage door . • Incorrect adjustment of garage door travel limits will interfere with proper operation of safety reversal system. • If one control (force or travel limits) is adjusted, the other contro ...
-
Chamberlain 3575 3 HP - page 24
ADJUSTMENT STEP 2 Adjust the Force Force adjustment controls are located on the right panel of the motor unit. Force adjustment settings regulate the amount of power required to open and close the door . If the forces are set too light, door travel may be interrupted by nuisance reversals in the down direction and stops in the up direction. Weather ...
-
Chamberlain 3575 3 HP - page 25
Without a properly installed safety reversal system, persons (particularly small children) could be SERIOUSL Y INJURED or KILLED by a closing garage door . • Safety reversal system MUST be tested ever y month. • If one control (force or travel limits) is adjusted, the other control may also need adjustment. • After ANY adjustments are made, t ...
-
Chamberlain 3575 3 HP - page 26
Using Y our Garage Door Opener Y our Security ✚ ® opener and hand-held remote control have been factory-set to a matching code which changes with each use, randomly accessing over 100 billion new codes. Y our opener will operate with up to eight Security ✚ ® remote controls and one Security ✚ ® Keyless Entry System. If you purchase a new r ...
-
Chamberlain 3575 3 HP - page 27
T o Open the Door Manually The door should be fully closed if possible. Pull down on the emergency release handle and lift the door manually . T o reconnect the door to the opener , press the door control push bar . The lockout feature prevents the trolley from reconnecting automatically . Pull the emergency release handle down and back (toward the ...
-
Chamberlain 3575 3 HP - page 28
CARE OF YOUR OPENER LIMIT AND FORCE ADJUSTMENTS: Weather conditions may cause some minor changes in door operation requiring some re-adjustments, particularly during the first year of operation. Pages 23 and 24 refer to the limit and force adjustments. Only a screwdriver is required. Follow the instructions carefully . Repeat the safety reverse tes ...
-
Chamberlain 3575 3 HP - page 29
29 HA VING A PROBLEM? 1. My door will not close and the light bulbs blink on my motor unit: The safety reversing sensor must be connected and aligned correctly before the garage door opener will move in the down direction. • V erify the safety sensors are properly installed, aligned and free of any obstructions. Refer to Installation Step 10: Ins ...
-
Chamberlain 3575 3 HP - page 30
Safety Sensor Bell Wire LED or Diagnostic LED "Learn" Button KG 1 3 9 7 5 KG 1 3 9 7 5 Diagnostics Located On Motor Unit 30 Installed Safety Sensor Y our garage door opener is programmed with self-diagnostic capabilities. The “Learn” button/diagnostic LED will flash a number of times then pause signifying it has found a potential issu ...
-
Chamberlain 3575 3 HP - page 31
*3-Button Remotes If provided with your garage door opener , the large button is factory programmed to operate it. Additional buttons on any Security ✚ ® 3-Button remote or compact remote can be programmed to operate other Security ✚ ® garage door openers. T o Erase All Codes From Motor Unit Memory T o deactivate any unwanted remote, first er ...
-
Chamberlain 3575 3 HP - page 32
KG 1 3 9 7 5 KG 1 3 9 7 5 1. Enter a four digit personal identification number (PIN) of your choice on the keypad. Then press and hold ENTER. 2. While holding the ENTER button, press and hold the LIGHT button on the Motion Detecting Door Control. 3. Continue holding the ENTER and LIGHT buttons while you press the push bar on the Motion Detecting Do ...
-
Chamberlain 3575 3 HP - page 33
1 3 4 5 6 2 33 REP AIR P ARTS Rail Assembly Parts KEY P ART NO. NO. DESCRIPTION 1 4A1008 Master link kit 2 41A4813 Chain pulley bracket 3 41A3489 Complete trolley assembly 4 1707LM One-piece rail 5 41D3484 Full chain assembly 6 83A1 1-2 Rail grease 7 10 11 5 NO TIC E UP CEILI N G M O U N T O N L Y 8 6 1 4 3 2 9 12 LOCK LIGHT Installation Parts KEY ...
-
Chamberlain 3575 3 HP - page 34
Motor Unit Assembly Parts 34 DN UP Brown Wire (Down) Contact LIMIT SWITCH ASSY . Grey Wire Y ellow Wire (Up) Contact Center Limit Contact Drive Gear 2 4 3 1 15 19 8A 17 5 18 9 10 16 14 13 12 6 6 11 8B 8C 7 7 KEY P ART NO. NO. DESCRIPTION 1 41A5615 Chain spreader 2 41A5585-1 Gear and sprocket assembly Complete with: Spring washer , thrust washer , r ...
-
Chamberlain 3575 3 HP - page 35
35 LOCK L IG HT CLOS ED O PE N ACCESSORIES 370LM 1708LM 41A5281 1702LM Outside Quick Release: Required for a garage with NO access door . Enables homeowner to open garage door manually from outside by disengaging trolley . 8 Foot (2.4 m) Complete Rail: T o allow an 8 foot (2.4 m) door to open fully . Designer Burled W alnut 3-Button Remote Control ...
-
Chamberlain 3575 3 HP - page 36
© 2007, The Chamberlain Group, Inc. 1 14A3086D All Rights Reserved LIFTMASTER ® SER VICE IS ON CALL OUR LARGE SERVICE ORGANIZA TION SP ANS AMERICA INST ALLA TION AND SERVICE INFORMA TION IS AS NEAR AS YOUR TELEPHONE. SIMPL Y DIAL OUR TOLL FREE NUMBER: 1-800-528-9131 www .liftmaster .com For professional installation, parts and service, contact yo ...
Hai una domanda su Chamberlain 3575 3 HP?
Utilizza il modulo sottostante
Se non hai risolto il problema con Chamberlain 3575 3 HP con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Chamberlain 3575 3 HP è probabile che voglia condividere il modo di risolverlo.