Italiano dropdown-ico

Manuale per l’uso Furuno 1623

48 pagine 1.77 mb
Scarica

Vai alla pagina of 48

Summary
  • Furuno 1623 - page 1

    MARINE RAD AR MODEL 1623 OPERA T OR'S MANU AL www .fur uno .co .jp MODEL Back ...

  • Furuno 1623 - page 2

    ...

  • Furuno 1623 - page 3

    i Ni-Cd Pb IMPORT ANT NOTICES General • The operator of this equipment must read and f ollow the descriptions in this manual. Wrong operation or maintenance can cancel the w arr anty or cause injury . • Do not copy any p art of this manual without written permission from FURUNO. • If this manual is lost or worn, contact your dealer about r ep ...

  • Furuno 1623 - page 4

    ii SAFETY INSTR UCTIONS Safety Instructions for the Operator WARNING ELECTRICAL SHOCK HAZARD Do not open the equipment. Only qualified personnel should work inside the equipment. Wear a safety belt and hard hat when working on the antenna unit. Serious injury or death can result if someone falls from the radar antenna mast. Do not disassemble or mo ...

  • Furuno 1623 - page 5

    iii T ABLE OF CONTENTS FORE WORD ............................................ iv SYSTEM CONFIG URA TION ..................... v EQUIP MENT L ISTS ................................. vi 1. OPERA TION........................................ 1 1.1 Controls ............................................... 1 1.2 Indica tions ............................... ...

  • Furuno 1623 - page 6

    iv FOREWORD A Word to the Owner of the MODEL 1623 Congratulations on your choice of the FURUNO MODEL 1623 Marine Radar . For over 60 years FURUNO Electric Company has en j oyed an env iable r eputation for innovative and dependable marine electronics equipment. This dedication t o excellence is furthered by our extensive global network of agent s a ...

  • Furuno 1623 - page 7

    v SYSTEM CONFIGU R A T ION DISPLA Y UNIT RDP-141 EXTERNAL BUZZER XH3-BZ-L970 12-24 VDC RECTIFIER PR-62 : Standard supply : Optional supply : Local supply 100/110/220/230 V AC , 1 φ , 50/60 Hz NA VIGA T OR or ECHO SOUNDER (NMEA 0183) GPS RECEIVER GP-310B/320B WIND INDICA T OR, SPEED INDICA T OR ANTENNA UNIT RSB-0093 ...

  • Furuno 1623 - page 8

    vi EQUIPMENT LI STS S ta ndar d supply Name T ype Code No. Qty Remark s Anten na Uni t RSB- 0093 — 1 Di spl ay Unit RD P- 141 — 1 CP03- 2530 1 008-442- 2 80 1 set For anten na u nit, i ncl uding EM I cor e CP03- 2491 0 000-080- 2 31 Anten na cab le ( 10 m ) CP03- 2492 0 000-080- 2 32 Anten na cab le ( 15 m ) CP03- 2493 0 000-080- 2 33 1 s et An ...

  • Furuno 1623 - page 9

    1 1. OPERA TION 1.1 Con tro ls Display unit How to remo ve the hard co ver Place your thumbs at the cent er of t he cover , and then lif t t he cover while pressing it with your thumbs. ...

  • Furuno 1623 - page 10

    1. OPER A TION 2 1.2 Indicatio ns TRAIL G(IN) ES H IR H FTC EBL VRM 45.0 ° 1.25 nm RNG 0.62nm BRG 283.2 ° TTG 0H7M 0.5 1.5 nm ZOOM Range Range ring inter val Zoom Echo trails Guard alar m (IN or OUT) Echo stretch Rain clutter suppressor Guard zone Cursor EBL Range rings Range, bearing and time-to-go to cursor location (Cursor latitude and longitu ...

  • Furuno 1623 - page 11

    1. OPER A TION 3 1.3 T ur ning Pow er On/Off Press the [POWER/B RILL] key to tu rn on the power . The unit beeps, the s tartup screen appears, and then the e quipm ent checks the ROM and RAM f or proper operation and displays program number . The ROM and RAM check shows OK or NG (No Good). If NG appears, try to press any key except the [PO W ER /BR ...

  • Furuno 1623 - page 12

    1. OPER A TION 4 1.5 A djusting Displa y Con trast, Brillian ce 1. Press the [P OWER/BR ILL] key momen taril y to show the brilliance/contr ast adjustment wi ndo w . CONT: 4 LOW HIGH BRILL: LOW HIGH 9 BRILL/CONTRAST TX/STBY - PRESS [MODE] [MENU/ESC] : Exit. Brilliance/contr ast adjustment window 2. Press ◄ or ► to ad just con trast. 3. Press ? ...

  • Furuno 1623 - page 13

    1. OPE RA TION 5 2. Press ▲ or ▼ to choose AUTO or MANU as appropriate. A utomatic g ain adjus tment a) Press ► to open the aut om at ic g ain options window . ROUGH MODERA TE CALM Automatic gain opt ions b) Press ▲ or ▼ to choose RO UG H, MODERA T E or CALM depending on sea conditions. c) Press ◄ to close t he window . Manual gain adju ...

  • Furuno 1623 - page 14

    1. OPER A TION 6 Manual A/C SEA adjustment W hile obser ving t he screen and the A/C SEA tuning bar , pr ess ◄ or ► to set the A/C SEA. T he set ting r ang e is 0-100. 4. Press th e [MEN U/ESC] key to f inish. 1.9 Suppressing Rain Clutter The vertical beamwidth of the antenna is designed to see surf ace tar g ets even when the ship is rolling . ...

  • Furuno 1623 - page 15

    1. OPE RA TION 7 6.0 nm 2.0 T arget VRM VRM range Range, bearing and time-to-go to cursor location RNG 2.22nm BRG 45.62 ° TTG 02H21M Cursor EBL - - - .- ° VRM 2.91 nm How to measur e t he range with t he VRM and cursor 1.11 Measuring th e Bearing The bearing t o a targ et can be m easur ed with the cursor and t he EBL ( Electronic Bearing Line). ...

  • Furuno 1623 - page 16

    1. OPER A TION 8 Select where to shift Shifted displa y with the cursor . Choose manual SHIFT mode. How the manual shif t works T o cancel the shi fted display , open the Display Mode menu, choose NORMAL and then press the [MENU/ESC] key . 1.13 Zoom The zoom feature allows you to double the size of a selected area. If zoom is activated when nav dat ...

  • Furuno 1623 - page 17

    1. OPER A TION 9 3. Press ► to show t he options w indow for the item selected. For example, the illustration below shows the interference rejector options window . OFF LOW MEDIUM HIGH Interference rejector options 4. Press ▲ or ▼ t o choose option desired. 5. Press ◄ to continue m enu operation, or press th e [ME NU/ESC ] key to re gister ...

  • Furuno 1623 - page 18

    1. OPER A TION 10 2. Press ▲ or ▼ to choose I NT REJEC T ION from p a ge 1. 3. Press ► to open the options wi ndo w . 4. Press ▲ or ▼ to choose OFF , LOW , MEDIUM or HIGH as appropriate. 5. Press t he [MENU/ESC] key to f inish. 1.17 N oise Rej ector The noise rejector suppresses w hite noise, which appears on the scr een as many dots scat ...

  • Furuno 1623 - page 19

    1. OPE RA TION 11 1.20 Guar d Alarm The guar d alarm allows the operator t o set the desired rang e and bearing f or a g uar d zone. W hen ships, islands, landmasses, etc. violate the guard zone, t he audio alar m sounds to call your attent ion. The alarm will sound on targ et s ent ering or exiting t he zone depending on zone status af ter the ala ...

  • Furuno 1623 - page 20

    1. OPER A TION 12 1.21 W atchman W atch m an transmits the radar f or one minute to check if a target h as entered or exited the guard zone from the prev ious tr ansmission. If no change is found, the radar g oes into standby for the number of minutes set f or the watchman f eature. If chang e is found, t he audio alarm sounds, watchman is canceled ...

  • Furuno 1623 - page 21

    1. OPER A TION 13 1.23 PROG Ke y The [PROG] k ey acts as a menu shortcut key . Y ou may use any User menu item ex cept “S YS T EM ME N U. ” Using the PROG key 1. Press t he [PROG] k ey . The options window corresponding to the item programmed appears. In the example below the echo stretch options w indo w is shown. OFF LOW HIGH ECHO STRETCH Ech ...

  • Furuno 1623 - page 22

    1. OPER A TION 14 1.25 T ur ning Naviga t ion Data On/Off Navigation data appears on the bott om half o f the screen as in the illustration below . Y ou may turn the navigation data display on o r of f as shown below . Note: When the nav dat a is turned on with shift or zoom active, zoom o r shift is cancelled. 1. Press t he [MODE] key . 2. Press ? ...

  • Furuno 1623 - page 23

    1. OPER A TION 15 GRAPHIC DISPLAYS DIGITAL DISPLAYS 1 0.5 0 0.5 1 Waypoint 03 Rng 0.19nm Brg 321 ° XTE 0.00nm Cse 333 ° DESTINA TION WA YPOINT GRAPHIC XTE scale Bearing, Course Destination waypoint direction Destination waypoint data: Name, Range to, XTE Wind APP* WIND GRAPHIC 60 120 90 0 30 150 180 120 150 90 60 30 120 ° Speed 10.3 m/s COMP ASS ...

  • Furuno 1623 - page 24

    1. OPER A TION 16 1.27 Sy stem Menu The System menu mainly contains ite m s which once set do not require f requent adjustment. Y ou may display t his menu by choosing “SYSTEM MENU” from page 3 o f the User menu and then pressing ► . SYSTEM MENU LANGUAGE English RANGE UNIT : nm DEPTH UNIT : ft SPEED UNIT : kt WIND UNIT : kt TEMP UNIT : ° F N ...

  • Furuno 1623 - page 25

    1. OPER A TION 17 P ANEL DIMMER: Y ou may adj ust panel backlighting from among OFF , LOW , MEDIUM and HIGH. HUE: The default hue se t ting (DA Y) display is most suitable for daytime v ie wing. For nig htt ime vi ewin g you may r ever se t his arran gement (N IGHT ). TR IPLOG RES ET : Y ou may reset distance run to zero by choosing YES. Navigat or ...

  • Furuno 1623 - page 26

    18 2. MAINTE NANCE, TROUBLESHOOTING WARNING ELECTRICAL SHOCK HAZARD Do not open the equipment. Only qualified personnel should work inside the equipment. NO TICE Do not apply paint, anti-corrosive sealant or contact spray to coating or plastic parts of the equipment. Those items contain organic solvents that can damage coating and plastic par ts, e ...

  • Furuno 1623 - page 27

    2. MAIN TENANCE , TROUBL ESHOOTING 19 2.2 Replac ing the Fus e The fuse (5 A) in the power cable protect s the equipment against reverse polarity of ship’s mains, overcur rent, and equipm ent fault. If the fuse blows, f ind the cause befor e replacing it. Use the proper fuse. Use of a wrong fuse may cause serious damage to the equipment and void ...

  • Furuno 1623 - page 28

    2. MAIN TENANCE, TROUBL ESHOOTING 20 2.4 Dia gnostic s If you feel that your unit is not working properly , conduct the appropriate diagnostic test, di splay u nit or an tenna unit, to find th e possible cause. If you cannot restore nor m al operation, contact your dealer for advice. Display unit 1. Tu rn on t he power while pressin g and holding d ...

  • Furuno 1623 - page 29

    2. MAIN TENANCE , TROUBL ESHOOTING 21 ANTENNA ST A TUS : OK(47)# HEADING : OK BEARING : OK (24.0r pm)* TUNE : T OT AL ON TIME : 00000h T O T AL TX TIME : 00000h INPUT NMEA RMA RMB RMC BWC GLL GGA MTW VTG VHW XTE VBW DPT DBK DBS DBT HDT HDG HDM BWR GLC GTD MWV ZD A * 24.0 = Long range 31.0 = Medium r ange 41.0 = Shor t range # = Status code. For ser ...

  • Furuno 1623 - page 30

    22 3. INST ALL A T ION 3.1 An ten na Un it In st al lat ion M ounti ng c on si dera tio ns W hen s e lec t ing a mou n t in g lo cat ion fo r t he ant enna u nit k eep i n mi nd th e foll owin g point s : • I nstall the a nten na uni t on t he h ardto p, radar ar c h or on a mas t on an appr o pr i at e plat form. ( For s ailbo ats, a mo untin g ...

  • Furuno 1623 - page 31

    3. INST ALLA TION 23 3. Using t he h exa gon head bol ts, flat was hers and sprin g was her s rem oved at step 1, f aste n the ant enna unit to t he plat form. Th e torqu e s hould be 1 9.6- 24.5 N • m. Flat washer Antenna base Spring washer Platform Hexagon head bolt (M10 x 20 or M10 x 25) *t Effective thread length 15 mm *t: Platform t ...

  • Furuno 1623 - page 32

    3. INS T ALLA T ION 24 7. Referr ing to the f igure below , f asten the shield cable with a screw (M 4x10) on the chassis to gr ound the unit. Connect 9 pin connector here (J801). Connect shield here. How to connect the antenna cable to the antenna unit 8. Attach the EMI core to the antenna cable. Set the EM I core fix ing pla te to the EMI core. P ...

  • Furuno 1623 - page 33

    3. INST ALLA TION 25 Mounting plate Suppor t plate (1) Suppor t plate (2) Brac ket (1) Brac ket (2) Fixing plate M8 x 20 M8 x 20 (A) Assembling the mounting brac ket M4 x 12 (B) Fastening antenna to mounting brac ket M10 x 25 M8 x 20 How to ass embl e the opti onal m ou nting brac ket and m ount the ante nna 4. Unfast en t hree s crews to ope n the ...

  • Furuno 1623 - page 34

    3. INST A LLA TION 26 3. 3 Wiring Conn ect the ante nna ca ble, the power cabl e and t he groun d wi re as show n b elow . FUSE (5 A) 12-24 VDC PO WER CABLE DISPLA Y UNIT ANTENNA UNIT ANTENNA CABLE * WHT (+) BLK (-) NMEA DJ-1 POWER 12-24 VDC 13 2 External Equipment (NMEA) GROUND Connect ground wire to bolt f astened (or welded) to hull. * = Do not ...

  • Furuno 1623 - page 35

    3. INST ALLA TION 27 Display unit, rear view 3. Close the rear panel, making sure the gask et is cor rectly positioned. 4. Plug in the connect or of t he external buzzer to J6 on the DU Board. 5. Seal the hole with sealing compound. 6. Fix the buzzer to the location desired with two tapping screws. 3.4 Adju stments Aft er you have installed the ra ...

  • Furuno 1623 - page 36

    3. INS T ALL A TION 28 8. Press ▲ to select YES, and t he display now looks as below . HEADING LINE ADJUSTMENT BY ’ ’ AND ’ ’ KEYS. THEN PUSH MODE KEY TO SET . Heading Line Message Heading adjustment display 9. Visually identif y a suitable tar g et (f or example, ship or buoy) at a rang e between 0.125 to 0.25 miles. 10. Point your boat? ...

  • Furuno 1623 - page 37

    3. INST ALLA TION 29 NM E A port setup, GPS W AAS setu p The NM EA p ort c an fu nction as an inp ut por t or i nput/ou tput port . I f you are usin g the GP-32 0B, tur n o n the GPS WA AS feat ure. 1. Show the I nst allati on me nu a nd th en pres s ▼ t o cho ose NM EA PORT . 2. Press ► t o display the NM EA por t opti ons wi ndow . 3. Press ? ...

  • Furuno 1623 - page 38

    MN-1 MENU TREE MENU/ESC key + POWER/BRILL key SIMULATION ( OFF , ON, HIGH) TEST (Tests display unit.) LCD PATTERN (Displays test pattern.) MEMORY CLEAR (Restores default menu settings.) NMEA PORT ( IN/OUT, IN/IN) NMEA OUTPUT ( OFF , ON) GPS WAAS ( OFF , WAAS 00-27) GO TO RADAR SETUP RAD AR SETUP HEADING ADJUST (Adjusts heading.) TIMING ADJUST (Adju ...

  • Furuno 1623 - page 39

    This page is intentionally left blank . ...

  • Furuno 1623 - page 40

    SP - 1 E3510S01F SPECIFI CA TIONS O F MARINE RA DA R MO DEL 1623 1 GEN ERA L 1.1 Indi cation Syst em PPI D aylight di splay, r aster sc an, 4 tones in monoc hrome 1.2 Range, Puls elength (PL) & Pulse Repeti tion Rate ( PRR) Range ( nm) 0.125, 0.25, 0.5, 0.75 1, 1.5, 2 3, 4, 6, 8, 12, 16 Pulse Length 0.08 μ s ( short) 0.3 μ s (m edium) 0.8 μ ...

  • Furuno 1623 - page 41

    SP - 2 E3510S01F 4.3 Range, Range I nterval , Number of Rings Range ( nm/km ) 0.125 0.25 0.5 0.75 1 1.5 2 3 4 6 8 12 16 24 Ri ng Inter val 0.0625 0.125 0.125 0.25 0.25 0.5 0. 5112 2 3 4 6 Num ber of Rings 2 2 4 3 4 3 4 3 4 3 4 4 4 4 R ange unit: nm/sm /km sel ectable, 0.125: nm/s m only, 24: k m only 4.4 M arkers Headi ng Line, Beari ng Scale, Rang ...

  • Furuno 1623 - page 42

    ＰＡＣＫＩＮＧ　ＬＩＳＴ 03GJ-X-9851 -15 MODEL1623-J-0/10/15/20, MODEL1623-E-0/10/15/20 N A M E O U T L I N E DESCRIPTION/CODE № Q'TY 1/1 ユニット U NIT 空中線部 ANTENNA UNIT RSB-0093-074 000-0 80-22 8-00 1 指示部 DISPLAY UNIT RDP-141-J/E 000-0 80-22 9-00 1 ** 空中線部工材 ANTENNA UNIT INS TALLA TION MATERIALS ? ...

  • Furuno 1623 - page 43

    Oct. 2, '02 D - 1 ...

  • Furuno 1623 - page 44

    Oct. 2, '02 D - 2 ...

  • Furuno 1623 - page 45

    Y. Hatai D - 3 ...

  • Furuno 1623 - page 46

    2 4 3 1 A B C MASS kg DRAWN CHECKED APPROVED SCALE NAME 名称 TITLE 相互結線図 MARINE RADAR INTERCONNEC TION DIAGRAM 船舶用レーダー MODEL 1623 03-160-6001-0 DWG.No. REF.No. 15/Feb/2011 T.YAMASAKI 15/Feb/2011 H.MAKI C3510-C01- E NOTE 注記 ＊４）空中線部のシールドは完全に アースする。 ＊５） ( ): MJ-A10SPF0009? ...

  • Furuno 1623 - page 47

    ...

  • Furuno 1623 - page 48

    The paper used in this manual is elemental chlorine free. ・FURUNO Authorized Distributor/Dealer 9-52 Ashihara-cho, Nishinomiya, 662-8580, JAPAN Telephone : +81-(0)798-65-2111 Fax : +81-(0)798-65-4200 A : OCT 2002 . Printed in Japan All rights reserved. G3 : MAR . 03, 2011 Pub. No. OME-35100-G3 *00080939214* *00080939214* ( YOSH ) MODEL1623 * 0008 ...

Fabbricante Furuno Categoria Marine RADAR

I documenti che otteniamo dal fabbricante del dispositivoFuruno 1623 possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Furuno
- manuali per l’uso 1623
- schede prodotto Furuno
- opuscoli
- o etichette energetiche Furuno 1623
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Furuno 1623.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Furuno 1623, manuali di manutenzione, brevi manuali o manuali utente Furuno 1623. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Furuno 1623.

Manuali per l’uso simili

Manuale completo del dispositivo Furuno 1623, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Furuno 1623 dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Furuno 1623.

Il manuale per l’uso completo Furuno, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Furuno 1623 - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Furuno 1623, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Furuno 1623 che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Furuno 1623 - che ci dovrebbe aiutare nei primi passi durante l'uso Furuno 1623
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Furuno 1623
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Furuno 1623 in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Furuno 1623?

Utilizza il modulo sottostante

Se non hai risolto il problema con Furuno 1623 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Furuno 1623 è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (1)

Tiziano

Come togliere la macchia centrale dal display