Italiano dropdown-ico

Manuale per l’uso CFM Corporation WMC36 WMC42

24 pagine 1.01 mb
Scarica

Vai alla pagina of 24

Summary
  • CFM Corporation WMC36 WMC42 - page 1

    For Models: WMC36 WMC42 For use in U.S./Canada Underwriter's Laboratories Report No. MH6018 DO NOT DISCARD THIS MANUAL: Retain for future use. 20000583 7/06 Rev . 20 FP583A WMC 12/18/98 WMC Series W oodburning Fireplace Homeowner's Installation and Operating Manual ...

  • CFM Corporation WMC36 WMC42 - page 2

    2 WMC Series W oodbur ning Fireplace 20000583 Safety Information PLEASE READ THIS MANUAL BEFORE INST ALLING AND USING FIREPLACE. IMPORT ANT : Read all instructions and warnings carefully before starting installation. Failure to follow these instructions may result in a possible fire hazard and will void the warranty . Description The WMC Series ? ...

  • CFM Corporation WMC36 WMC42 - page 3

    3 WMC Series W oodb ur ning Fireplace 20000583 50" (1270mm) 42" (1067mm) 35 ¹⁄ ₄ " (895mm) 46" (1 168mm) ⁵⁄₈ " (16mm) ⁵⁄₈ " (16mm) ¹⁄₂ " (13mm) ¹⁄₂ " 19 ³⁄₄ " (502mm) 1 ³⁄₄ " (45mm) 38" (965mm) 21" (533mm) 7 ³⁄₄ " (197mm) 7 ¹ ⁄₂ " ...

  • CFM Corporation WMC36 WMC42 - page 4

    4 WMC Series W oodb ur ning Fireplace 20000583 Chase Installation Insulation methods shown are optional for cold climate, not a requirement for unit operation. FPC554 Fig. 3 Fireplace and chase parts identification. T ermination Cap Storm Collar Pan Flashing Draftstop T op Shield Surround Outlet Grille Damper Control Gas Line Knockout (both sides) ...

  • CFM Corporation WMC36 WMC42 - page 5

    5 WMC Series W oodb ur ning Fireplace 20000583 D RISE B G H B OFFSET C E 6 FT . G H A HEARTH FLOOR CHIMNEY SECTION CHIMNEY FLUE EXIT ELBOW FPC269 Chimney Requirements -typ. offset Circulating models 1/28/99 djt 30˚ OFFSET ELBOW 30˚ OFFSET ELBOW 30˚ RETURN ELBOW 30˚ RETURN ELBOW SKCS8 SUPPORT Example 1 Example 2 Example 3 Chimney Requirements - ...

  • CFM Corporation WMC36 WMC42 - page 6

    6 WMC Series W oodb ur ning Fireplace 20000583 Planning Information Preplanning an installation is very important to ensure safety and to save time and money . An installer must predetermine where a fireplace will be set and how the chimney system will be run. Mounting the Fireplace A fireplace may be mounted on the following surfaces: 1. A flat ...

  • CFM Corporation WMC36 WMC42 - page 7

    7 WMC Series W oodb ur ning Fireplace 20000583 Chimney Supports The chimney system is supported by the fireplace for vertical chimney heights less than 30' (9 m) above the hearth. Chimney supports are required if the vertical height exceeds 30' (9 m) with SK8 chimneys or 20' (6 m) with 3-wall chimneys. Locate chimney supports at cei ...

  • CFM Corporation WMC36 WMC42 - page 8

    8 WMC Series W oodb ur ning Fireplace 20000583 Framing Framing can be constructed before or after the fire- place is set in place, however , most installers build the frame before setting the fireplace. Frame fireplace with 2 x 4 lumber or heavier materials. Refer to framing dimensions in Figures 1 and 2 for basic fireplace specifications. NOT ...

  • CFM Corporation WMC36 WMC42 - page 9

    9 WMC Series W oodb ur ning Fireplace 20000583 Chimney Set-up Since you have already preplanned the chimney run, you should know exactly how the installation is to be accomplished - how much pipe is required, the number of elbows, if any , and type of termination to be used. CAUTION: REPORT TO YOUR DEALER ANY P ARTS DAMAGED IN SHIPMENT , SPECIFICAL ...

  • CFM Corporation WMC36 WMC42 - page 10

    10 WMC Series W oodb ur ning Fireplace 20000583 Framing the Ceiling Hole Frame the ceiling chimney hole as shown in Figure 13. It is good practice to use framing lumber that is the same size as the ceiling joists; this is a requirement at attic level. The following table gives firestop spacer model num - bers: Safety strips are used to ensure that ...

  • CFM Corporation WMC36 WMC42 - page 11

    1 1 WMC Series W oodb ur ning Fireplace 20000583 Installing Outside Air Kit An outside air kit is installed in all WMC Series Fire- places. If desired, or if local codes mandate the use of an air kit, then an AK-MST is required to complete the installation (from air kit to the outdoors). If the outside air kit is to be used, the AK-MST MUST be inst ...

  • CFM Corporation WMC36 WMC42 - page 12

    12 WMC Series W oodb ur ning Fireplace 20000583 FP593 SR/C 11/20/97 Fig. 19 Installing firestop spacer . FP593 Nails (4) Firestop Spacer Joist Attic Installation Ceiling Installation Joist Firestop Spacer Nails (4) FP263 Fig. 20 Attic shield installlation (Canadian requirement). IGF263 MBUF 5/9/96 Attic Insula- tion Shield Ceiling Base Flanges Nai ...

  • CFM Corporation WMC36 WMC42 - page 13

    13 WMC Series W oodb ur ning Fireplace 20000583 adjacent combustible surfaces. (Combustible surfaces include burnable materials such as: ceiling members, joists, flooring, combustible insulation and roof struc- tures.) W ARNING: DO NOT P ACK REQUIRED AIR SP ACES WITH INSULA TION OR OTHER MA TERIALS. Mark an outline of the roof hole around the cent ...

  • CFM Corporation WMC36 WMC42 - page 14

    14 WMC Series W oodb ur ning Fireplace 20000583 NOTE: No side wall protection is required for fireplaces installed at 45° to two (2) side walls (corner installation). Often a decorative surround or vertical portion of the mantel is desired. If this is constructed of any combus- tible material it must be within the safe zone indicated in Figure 23 ...

  • CFM Corporation WMC36 WMC42 - page 15

    15 WMC Series W oodb ur ning Fireplace 20000583 Hearth Installation A hearth extension is required to protect a combustible floor in front of the fireplace. Refer to Figure 24 for minimum dimensions and mounting detail. NOTE: Hearth Extension must not cover the air inlet/outlet opening of a fireplace. The hearth extension described in Figure 24 ...

  • CFM Corporation WMC36 WMC42 - page 16

    16 WMC Series W oodb ur ning Fireplace 20000583 COMMON MA TERIALS AND F ACTORS MA TERIAL K* R MINIMUM THICKNESS EH2416 Common Brick 0.458 5.0 1.09 0.50 in.** 0.10 5.46 in.** (CFM Corporation) R V alue is for Zx inch. * Units of K = BTU/SQ FT/HR/˚F/IN ** Thickness of Listed Material FP533ADD Addendum 6/1/99 djt 8/4/99 changed .2 to .1 one inch to ...

  • CFM Corporation WMC36 WMC42 - page 17

    17 WMC Series W oodb ur ning Fireplace 20000583 Only unvented gas log sets which have been found to comply with the Standard for Unvented Room Heaters, ANSI Z21.1 1.2, are to be installed in this fireplace. If installing an unvented gas log set, refer to statement below: Installing Line for Gas Logs CFM Corporation fireplaces are designed to acce ...

  • CFM Corporation WMC36 WMC42 - page 18

    18 WMC Series W oodb ur ning Fireplace 20000583 2-583 Parts page 3/2/99 djt 1 2 3 4 5 6 7 12 8 10 9 1 1 15 14 17a,b 16 18 19 20 OFF L O W 21 13 583 CFM Corporation reserves the right to make changes in design, materials, specificaitons, prices and discontinue colors and products at any time, without notice. WMC36/42 W oodburning Fireplace 1. Dampe ...

  • CFM Corporation WMC36 WMC42 - page 19

    19 WMC Series W oodb ur ning Fireplace 20000583 The following accessories for this appliance are available from your local distributor . Should you need additional in- formation beyond what your distributor can furnish, contact: CFM Corporation, 2695 Meadowvale Blvd., Mississauga, Ontario, Canada L5N 8A3; Attn: T echnical Services. CAUTION: This ? ...

  • CFM Corporation WMC36 WMC42 - page 20

    20 WMC Series W oodb ur ning Fireplace 20000583 Chimney Components Round T op T ermination T op used to terminate chimney at roof. RL TSK8 (SK8) (Flashing not included.) Round T op T ermination - T op used to terminate chimney at chase. RL TSK8L Extended (SK8) (Flashing not included.) Flashing Metal finishing required around Contemporary 8-6-12 wi ...

  • CFM Corporation WMC36 WMC42 - page 21

    21 WMC Series W oodb ur ning Fireplace 20000583 Model Number Description Component (Chimney Components con't.) Square Chase T ermination Square chimney cap used to terminate chimney SL TS8 through chase. Includes adapter . (Flashing material) Adapter Kit Required to unite 3-wall chimney with S20BR, S20UB S20BT , S20BW T raditional T op Housing ...

  • CFM Corporation WMC36 WMC42 - page 22

    22 WMC Series W oodb ur ning Fireplace 20000583 ...

  • CFM Corporation WMC36 WMC42 - page 23

    23 WMC Series W oodb ur ning Fireplace 20000583 LIMITED W ARRANTY & 30 YEAR PROTECTION PLAN For MAJESTIC FIREPLACES PRE-ENGINEERED Fireplace Systems CFM Corporation warrants its Pre-Engineered Fireplace (“Fireplace”) and the CFM Corporation-supplied firegrate, glass doors, outside air system, fan motor , and liners to be free from defects ...

  • CFM Corporation WMC36 WMC42 - page 24

    2695 Meadowvale Blvd. • Mississauga, Ontario, Canada L5N 8A3 800-668-5323 • www .cfmcorp.com CFM Corporation ...

Fabbricante CFM Corporation Categoria Indoor Fireplace

I documenti che otteniamo dal fabbricante del dispositivoCFM Corporation WMC36 WMC42 possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici CFM Corporation
- manuali per l’uso WMC36 WMC42
- schede prodotto CFM Corporation
- opuscoli
- o etichette energetiche CFM Corporation WMC36 WMC42
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso CFM Corporation WMC36 WMC42.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione CFM Corporation WMC36 WMC42, manuali di manutenzione, brevi manuali o manuali utente CFM Corporation WMC36 WMC42. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto CFM Corporation WMC36 WMC42.

Manuali per l’uso simili

Manuale completo del dispositivo CFM Corporation WMC36 WMC42, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare CFM Corporation WMC36 WMC42 dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti CFM Corporation WMC36 WMC42.

Il manuale per l’uso completo CFM Corporation, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale CFM Corporation WMC36 WMC42 - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice CFM Corporation WMC36 WMC42, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per CFM Corporation WMC36 WMC42 che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo CFM Corporation WMC36 WMC42 - che ci dovrebbe aiutare nei primi passi durante l'uso CFM Corporation WMC36 WMC42
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del CFM Corporation WMC36 WMC42
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio CFM Corporation WMC36 WMC42 in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su CFM Corporation WMC36 WMC42?

Utilizza il modulo sottostante

Se non hai risolto il problema con CFM Corporation WMC36 WMC42 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con CFM Corporation WMC36 WMC42 è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)