Italiano dropdown-ico

Manuale per l’uso ACR Electronics Nauticast AIS-300

32 pagine 1.52 mb
Scarica

Vai alla pagina of 32

Summary
  • ACR Electronics Nauticast AIS-300 - page 1

    ...

  • ACR Electronics Nauticast AIS-300 - page 2

    2 Y1 -03 - 0222 Rev. C In the United State s W ARNING: It is a violat ion of the rules of the Federal Com m unications Comm ission to input an M MSI that h as not been pro perly assigned t o the end user, or to otherwise input any inaccurate data in t his device. WARNING: T his product is a supp lemental navigat ion tool only! The user assum es all ...

  • ACR Electronics Nauticast AIS-300 - page 3

    3 Y1 -03 - 0222 Rev. C Table of Contents SECTION 1 - WHAT IS AIS? ____________________________________________________________ 4 SECTION 2 - INSTALLATION ___________________________________________________________ 6 SECTION 3 - USING THE TRANSPONDER ________________________________________________ 20 SECTION 4 - MAINTENANCE ________________________ ...

  • ACR Electronics Nauticast AIS-300 - page 4

    4 Y1 -03 - 0222 Rev. C SECTION 1 - W HA T IS A IS? 1. Overview AIS is an acronym for A utomatic I dentification S ystem . AIS increases navigational safety and collision avoidance b y transm itting vessel iden tification, h elping to r educe the d ifficulty of ide ntif ying ships w hen not in sight (e.g. at night, in radar blind arcs or s hadows or ...

  • ACR Electronics Nauticast AIS-300 - page 5

    5 Y1 -03 - 0222 Rev. C On the bottom , a t ypical N auticast™ -B AIS installation in a comm on environm ent is shown. T he Nauticast™ -B AIS is connec ted t o the vess el ‟ s power supply, and, in connecti on with the VHF and GPS antennas, th e m inimal requirements for transpond er operation are f ulfilled. Both vessels in the ab ove il lust ...

  • ACR Electronics Nauticast AIS-300 - page 6

    6 Y1 -03 - 0222 Rev. C In order to m eet carriage re quirements f or Class A and Class B AIS s ystems, dedic ated GPS and VHF anten nas must be fit to the transponders. ACR has include d GPS and VHF antenn as that have been spec ifically designed, t ested and approved for use with the Nauticast ™ -B. A CR Electronics Inc . does not recom m end or ...

  • ACR Electronics Nauticast AIS-300 - page 7

    7 Y1 -03 - 0222 Rev. C 2. Installa tion overview and prerequisites In the United State s W ARNING: It is a violat ion of the rules of the Federal Com m unications Comm ission to input an M MSI that h as not been pro perly assigned t o the end user, or to otherwise input any inaccurate data in t his device. The US FCC regulat ion states that “T he ...

  • ACR Electronics Nauticast AIS-300 - page 8

    8 Y1 -03 - 0222 Rev. C Or, when you have do wnloaded an upgr ade: Unzip the pack age when necessar y and start the installer prog ram as des cribed in “Installatio n of the Link2AIS™ Software” (later in this secti on). If one of the f ollowing dialogs is shown w hen the installation proc ess is started, the .NET ® framework and/or the W indo ...

  • ACR Electronics Nauticast AIS-300 - page 9

    9 Y1 -03 - 0222 Rev. C W hen you are not connected to the internet, an error m essage like the one below will be shown. From the CD If you do not want to download the .NET® framework from the Microsof t website, term inate the d ownload process by c licking the “Cancel” button in the downloa d dia log box and install the package directly f rom ...

  • ACR Electronics Nauticast AIS-300 - page 10

    10 Y1 -03 - 0222 Rev. C W hen the i nstallation pro cess has finished, you MUST reboot your c omputer in order to install th e Link2AIS ™ Software: 6. Installation of the Link2AIS™ Software Unzip the downloade d pack age when necessary. Locate the files “setup .exe” and the accom panying “msi” file, then doubl e - click on “s etup.exe ...

  • ACR Electronics Nauticast AIS-300 - page 11

    11 Y1 -03 - 0222 Rev. C A dialog box will appear re m inding you to uninstall any prior v ersions of the L ink2AIS™ software ( if applicable) before c ontinuing the instal l process. Read through and ac cept the license agreem ent and click Next. ...

  • ACR Electronics Nauticast AIS-300 - page 12

    12 Y1 -03 - 0222 Rev. C The next screen will allow you to pick options to be installed. T hese options ar e check ed by default. Choose a director y where the software will be installed . Make note of this d irectory, as you will need to manuall y copy files to this location later on in the instal l process. ...

  • ACR Electronics Nauticast AIS-300 - page 13

    13 Y1 -03 - 0222 Rev. C The software will ask you to choose a locati on in the Start m enu to place the pro gram‟s s hortcuts: The next screen will ask y ou to co nfirm the install sett ings you have provided in the previous s teps: ...

  • ACR Electronics Nauticast AIS-300 - page 14

    14 Y1 -03 - 0222 Rev. C Now the application will install autom atically in the folder you have chosen : The install program will tell you when ins tallation has b een completed. C lick Finish. Finally, find the Coas tlines folder on the insta llation CD and copy to the insta ll directory chosen dur ing the install process. If you are unable to find ...

  • ACR Electronics Nauticast AIS-300 - page 15

    15 Y1 -03 - 0222 Rev. C You will find the instal led program shortcuts i n the Star t Menu / All Programs/ ACR Electronics director y (unless you chose a dif ferent location durin g the install proc ess) . A shortcut nam ed “Link2AIS” will be place d on your desk top. Use either shortcut to launch the program . 7. Connecting to a personal compu ...

  • ACR Electronics Nauticast AIS-300 - page 16

    16 Y1 -03 - 0222 Rev. C Start up Link2AIS ™ Softwa re program on PC . The initial app lication screen wil l appear as shown: The application requires a serial connec tion to a N auticast™ - B AIS trans ponder. Connect the transponder to an available serial port. If y our serial port is not located in the drop dow n box, s elect „New…‟ and ...

  • ACR Electronics Nauticast AIS-300 - page 17

    17 Y1 -03 - 0222 Rev. C To configure the transpo nder all of the dat a fields m ust be completed and sa ved to the AIS. WARNING: Per FCC rules (United States us ers only) the static data of the vesse l cannot be c hanged once programm ed. Do not progr am the static data un less you are certain y ou have the correct information. Please check the num ...

  • ACR Electronics Nauticast AIS-300 - page 18

    18 Y1 -03 - 0222 Rev. C For additional software applications unrel ated to the installation, please ref er to the Link2AIS™ Software user guide for technical s upport. 11. Hardware installation WARNING : T he compass safe distance of this unit is 0.5m or gr eater for 0.3 ° dev iation. WARNING: Do not connect the N auticast™ -B AIS unit to a ma ...

  • ACR Electronics Nauticast AIS-300 - page 19

    19 Y1 -03 - 0222 Rev. C If using PC s erial term inal with third part y AIS ca pable Elec tronic Charting Soft ware, connect the user end of the data interface c able to the displa y device. The sof tware in the displ ay device m ust be configured for AIS operation AND to accept st andard Class B AIS operation NMEA sentences. This external displa y ...

  • ACR Electronics Nauticast AIS-300 - page 20

    20 Y1 -03 - 0222 Rev. C The GPS antenna has a free view through 360 degrees with a vertical angle of 5 to 90 degre es above the horizon. The GNSS antenna i s placed as far away as possib le from radar, Inmarsat and Irid ium transmitters . Also ensure that the GPS ante nna is free from direct view of the radar an d the Inm arsat beam. T he received ...

  • ACR Electronics Nauticast AIS-300 - page 21

    21 Y1 -03 - 0222 Rev. C If the r ed LED i lluminates continuously, the un it should be ass umed to be f aulty. It s hould either b e s witched off (power r emoved) or, if this is not prac tical, any other vessel position inform ation derived f rom the unit should not be used. It shou ld also be ass umed that the unit is not t ransmitting valid posi ...

  • ACR Electronics Nauticast AIS-300 - page 22

    22 Y1 -03 - 0222 Rev. C TX timeout This is a yellow LED which indicates when lit that t he CST DMA transm itter is prevent ed from transm itting. Reasons for this include the following: The transpond er‟s intern al GPS r eceiver is not yet r eady. The y ello w LED will go out a nd the green LED will light when G PS receiver is read y. The transpo ...

  • ACR Electronics Nauticast AIS-300 - page 23

    23 Y1 -03 - 0222 Rev. C Data A minimum keypad and d ispla y (MKD) unit, chart plotter or other d isplay device may be connected to the N auticast™ -B AIS unit via the a ppropriate cable assem bly. The default baud rate of the data link is 38.4k baud with 8 data b its, one stop bit and no parit y. The data interface conforms to IEC 61162- 1. VDM, ...

  • ACR Electronics Nauticast AIS-300 - page 24

    24 Y1 -03 - 0222 Rev. C NOTE 2 The sequential mess age identifier prov ides a message identification num ber from 0 to 9 that is sequentially assigned and is increm ented for each new m ulti -sentence m essage. T he count resets to 0 after 9 is used. For a m essage r equiring m ultiple s entences, each sentence of the message contains the sam e seq ...

  • ACR Electronics Nauticast AIS-300 - page 25

    25 Y1 -03 - 0222 Rev. C 5. VHF data link own vessel messages (NME A 0183 VDO) This mess age describes your own vessel m essage being sent. VDO message f ormat ! -- VDO,x1,x2,x3,a,s -- s ,x*hh<CR><LF> field 1 2 3 4 5 6 Field Format Description 1 x Total number of sentences need ed to transf er the message 1 , 1 to 9 2 x Sentence num ber ...

  • ACR Electronics Nauticast AIS-300 - page 26

    26 Y1 -03 - 0222 Rev. C 6. Regional Assignment Channel Assignment Message (NMEA 0183 ACA) A N auticast™ - B unit ca n receive regional channel m anagem ent inform ation in t wo ways: ITU -R M.1 371 message 22 or a DSC te lecom m and received on channel 70. C hannel m anagem ent inform ation is applied based upon the actual location of the AIS dev ...

  • ACR Electronics Nauticast AIS-300 - page 27

    27 Y1 -03 - 0222 Rev. C 8. AIS alarm messa ges (NMEA 0183 ALR, Text) Local alarm condition and status. T his sentence is us ed to report an alarm condition on a device and its current state of ack nowledgement. ALR message format ! -- ALR,hhmmss.ss,xxx ,A,A,c -- c*hh<CR><LF> field 1 2 3 4 5 Field Format Description 1 x hhmmss.ss = T ime ...

  • ACR Electronics Nauticast AIS-300 - page 28

    28 Y1 -03 - 0222 Rev. C A PPENDIX B - SPEC IFICATIONS AN D WARNINGS 1. Specifications Parameter Value Dimensions 7.8 x 6.22 x 1.84 in. ( 198 x 158 x 46.7 mm ) W eight 13.2 oz (375g) Power DC (9.6-15.6V), t wo-wire with ne gative ground Average power consum ption 4W Peak current rating 2A GPS Receiver (AIS Intern al) IEC 61108-1 com pliant Electrica ...

  • ACR Electronics Nauticast AIS-300 - page 29

    29 Y1 -03 - 0222 Rev. C 2. Warnings WARNING regarding VHF antenna connectio n: Connecti ng a badl y mismatc hed VHF antenna, leav ing the VHF antenna port d isconnected, or s horting the V HF antenna port wil l activate the VSW R alarm, c ausing the unit to stop sending p osition reports or ca using dam age to the transpon der and activating the re ...

  • ACR Electronics Nauticast AIS-300 - page 30

    30 Y1 -03 - 0222 Rev. C A PPENDI X D - DATA POWER C AB LE I NFOR M A TION Class B A2 - 07 -0196-1 DATA POWER CABLE J1 J2 Description DB15 DB9 Wire Type Color AWG CABLE # 12V + 1 Tinned Copper RED 18 CABLE1 12V - 9 Tinned Copper BLACK 18 CABLE1 RS422 TX A 2 Tinned Copper ORANGE 22 - 24 CABLE 2 RS422 RX A 3 Tinned Copper YELLOW 22 - 24 CABLE 2 RS422 ...

  • ACR Electronics Nauticast AIS-300 - page 31

    31 Y1 -03 - 0222 Rev. C APPENDIX E - SUPPORT, W A RRANTY, USEFUL LIFE and NOTICES 1. Support Contact your local deal er for Nauticast™ -B AIS support. Please visit the ACR W ebsite for Service centers near you. ACR Electronics Europe GmbH Handelskai 388 / Top 632 A-1020 Vienna, Aus tria Tel: +43 (1) 5 237 237 - 0 Fax: +43 (1) 5 237 237 - 150 Emai ...

  • ACR Electronics Nauticast AIS-300 - page 32

    32 Y1 -03 - 0222 Rev. C EC DECL A R ATION OF CO NFORMITY ACR Electronics, Inc . hereby declares that the following pro duct is in conform ity with Directive 19 99/5/EC of the European Parliam ent and o f the Council of 9 March 1999 on Radio eq uipm ent and Telecomm unications Term inal Equipment (R&TTE), and h as been t ype examined as follows. ...

Fabbricante ACR Electronics Categoria Marine GPS System

I documenti che otteniamo dal fabbricante del dispositivoACR Electronics Nauticast AIS-300 possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici ACR Electronics
- manuali per l’uso Nauticast AIS-300
- schede prodotto ACR Electronics
- opuscoli
- o etichette energetiche ACR Electronics Nauticast AIS-300
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso ACR Electronics Nauticast AIS-300.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione ACR Electronics Nauticast AIS-300, manuali di manutenzione, brevi manuali o manuali utente ACR Electronics Nauticast AIS-300. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto ACR Electronics Nauticast AIS-300.

Manuali per l’uso simili

Manuale completo del dispositivo ACR Electronics Nauticast AIS-300, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare ACR Electronics Nauticast AIS-300 dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti ACR Electronics Nauticast AIS-300.

Il manuale per l’uso completo ACR Electronics, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale ACR Electronics Nauticast AIS-300 - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice ACR Electronics Nauticast AIS-300, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per ACR Electronics Nauticast AIS-300 che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo ACR Electronics Nauticast AIS-300 - che ci dovrebbe aiutare nei primi passi durante l'uso ACR Electronics Nauticast AIS-300
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del ACR Electronics Nauticast AIS-300
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio ACR Electronics Nauticast AIS-300 in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su ACR Electronics Nauticast AIS-300?

Utilizza il modulo sottostante

Se non hai risolto il problema con ACR Electronics Nauticast AIS-300 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con ACR Electronics Nauticast AIS-300 è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)