Italiano dropdown-ico

Manuale per l’uso KTI Networks KS-2260

153 pagine 5.06 mb
Scarica

Vai alla pagina of 153

Summary
  • KTI Networks KS-2260 - page 1

    -1- DOC.030425-KS2260-K 10/100 Managed Fast Ethernet Switch with 100FX and Gigabit Connectivity KS-2260 Optional 100FX Modules Optional Gigabit Modules Operation Manual ...

  • KTI Networks KS-2260 - page 2

    -2- (C) 2002 KTI Networks Inc. All rights reserved. No part of this documen- tation may be reproduced in any form or by any means or used to make any directive work (such as translation or transformation) without per- mission from KTI Networks Inc. KTI Networks Inc. reserves the right to revise this documentation and to make changes in content from ...

  • KTI Networks KS-2260 - page 3

    -3- The information contained in this document is subject to change without prior notice. Copyright (C) KTI. All Rights Reserved. TRADEMARKS Ethernet is a registered trademark of Xerox Corp. W ARNING: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits a ...

  • KTI Networks KS-2260 - page 4

    -4- T able of Contents 1. Introduction ................................................................ 8 1.1 Introduction .................................................................................... 8 1.2 Features ........................................................................................ 9 1.3 Hardware Specifications ........ ...

  • KTI Networks KS-2260 - page 5

    -5- 3.2 Switch Static Configuration ......................................................... 4 6 3.2.1 Port Configuration .................................................................... 4 7 3.3.2 Trunk Configuration .................................................................. 4 9 3.3.3 VLAN Configuration ................................ ...

  • KTI Networks KS-2260 - page 6

    -6- 3.4.6 802.1X ....................................................................................... 8 1 3.4.6.1 Enable 802.1X Protocol ......................................................... 8 2 3.4.6.2 802.1X System Configuration ............................................... 8 2 3.4.6.3 802.1X Per Port Configuration ...................... ...

  • KTI Networks KS-2260 - page 7

    -7- 5.5.6.1 IGMP Snooping .................................................................... 12 1 5.5.6.2 Static MAC Address ............................................................. 1 2 2 5.5.6.3 MAC Address Filtering ......................................................... 1 2 3 5.5.7 VLAN configuration .................................... ...

  • KTI Networks KS-2260 - page 8

    -8- 1. Introduction 1.1 Introduction Driven by recent advances in desktop computing technology , t od ay ’ s network applications have increased in speed, power and the ability to process information. T o meet the demands of these more bandwidth- intensive applications, this switch device provides significant increase in performance for your Ethe ...

  • KTI Networks KS-2260 - page 9

    -9- 1.2 Features • 19-inch rack mountable 24-Port 10/100 managed Fast Ethernet switch with two Giga expansion port slots • Provides two alternative 100Base-FX port slots for fiber connections • Non-blocking and store-and-forward switch engine performs forwarding and filtering at full wire speed. • Supports diversified optional Giga port mod ...

  • KTI Networks KS-2260 - page 10

    -10- 1.3 Hardware Specifications 10/100 Switched Ports Port 1 ~ 24, T otal : 24 ports 802.3 10Base-T , 802.3u 100Base-TX compliant Shielded RJ-45 with auto MDI-X function Port 23, 24 Alternatives 100Base-FX connectivity 2 expansion module slots - Slot F23, F24 Giga Switched Ports 2 expansion Slots - Slot G1, G2 802.3z and 802.3ab compliant Supports ...

  • KTI Networks KS-2260 - page 11

    -11- Network Access Control 802.1X protocol support for all ports Function Radius client configuration Per port mode - Auto, Fu, Fa, No QoS Function 2-level (High/Low) priority for Tx queues Selectable Tx High/Low service ratio Priority Decision Method First - Port-based priority Second - 802.1p priority (T ag priority value) V L A N Function Mode ...

  • KTI Networks KS-2260 - page 12

    -12- 1.4 Software Specifications Management interface In-band SNMP over TCP/IP network In-band W eb browser over TCP/IP network In-band T elnet over TCP/IP network Out-of-band via Console port SNMP Traps over TCP/IP network RFC & Protocols I Pv 4 IP version4 RFC791 T C P Transmission Control Protocol RFC793 U D P User Datagram Protocol RFC768 A ...

  • KTI Networks KS-2260 - page 13

    -13- 1.4.1 Management Objects List of management objects supported by console and T elnet interfaces : Management Objects Console T elnet W eb SNMP Boot diagnostics Y es - - - Login check Y es Y es Y e s - Port configuration Y es Y es Y es - Trunk configuration (& LACP) Y e s Y es Y e s - VLAN configuration Y es Y e s Y es - QoS Priority config ...

  • KTI Networks KS-2260 - page 14

    -14- Management Objects Console T elnet W eb SNMP Port state - enable/disable Y es Y es Y es Y es Port status - link, speed Y es Y es Y es Y es Port static counters Y es Y es Y es Y es Device Mac address information Y es Y es Y es Y es System firmware version information Y e s Y es Y e s - System hardware version information Y es Y es Y es - System ...

  • KTI Networks KS-2260 - page 15

    -15- 1.5 Function Descriptions 1.5.1 LACP T runking Function The switch provides a trunking function, which is compliant with 802.3ad standard. 802.3ad is a specification from IEEE that allows us to bundle several physical port links together to form one logical port , called a trunk between two devices. It supports Link Aggregation Control Proto- ...

  • KTI Networks KS-2260 - page 16

    -16- same time. Those member ports which are not work ports are standby to become work port if any current work port fails to operate. This transition takes about 30 seconds. Each member port can be set LACP Passive or LACP active as described below: LACP Passive : The port does not initiate the LACP negotiation, but it does understand the LACP pac ...

  • KTI Networks KS-2260 - page 17

    -17- 1.5.2 IP Multicast Function Internet Protocol (IP) multicast is a bandwidth-conserving technology that reduces traffic by simultaneously delivering a single stream of infor- mation to thousands of corporate recipients and homes. Applications that take advantage of multicast include video conference, corporate communications, distance learning, ...

  • KTI Networks KS-2260 - page 18

    -18- IGMP Internet Group Management Protocol (IGMP) is used to dynamically register individual hosts in a multicast group on a particular LAN. Hosts identify group memberships by sending IGMP messages to their local multicast router . Under IGMP , routers listen to IGMP messages and peri- odically send out queries to discover which groups are activ ...

  • KTI Networks KS-2260 - page 19

    -19- IGMP Snooping IGMP snooping requires the LAN switch to examine, or snoop, some Layer 3 information in the IGMP packets sent between the hosts and the router . When the switch hears the IGMP host report from a host for a particular multicast group, the switch adds the host's port number to the associated multicast table entry . When the sw ...

  • KTI Networks KS-2260 - page 20

    -20- 1.5.4 Static MAC Address The switch provides Static MAC Address setup function. The static MAC addresses are the MAC addresses which are setup by LAN admin- istrators and are not learned by the switch automatically . The static addresses are stored and referred in switch MAC address table permanently regardless of whether the MAC addresses are ...

  • KTI Networks KS-2260 - page 21

    -21- 1.5.6 VLAN Function V irtual LANs (VLANs) can be viewed as a group of devices on different physical LAN segments which can communicate with each other as if they were all on the same physical LAN segment. It can create a network that is independent of physical location and group users into logical workgroups. The benefits are: • Confine broa ...

  • KTI Networks KS-2260 - page 22

    -22- 1.5.6.2 IEEE 802.1Q VLAN (T ag-based VLAN) T ag-based VLAN is an IEEE 802.1Q specification standard. Therefore, it is possible to create a VLAN across devices from different venders. IEEE 802.1Q VLAN uses a technique to insert a tag into the Ethernet frames. T ag contains a VLAN Identifier (VID) that indicates the VLAN numbers. The switch can ...

  • KTI Networks KS-2260 - page 23

    -23- 1.5.6.3 Protocol-based VLAN In order for an end station to send packets to different VLANs, it itself has to be either capable of tagging packets it sends with VLAN tags or attached to a VLAN-aware bridge that is capable of classifying and tag- ging the packet with different VLAN ID based on not only default PVID but also other information abo ...

  • KTI Networks KS-2260 - page 24

    -24- re-configures the spanning-tree topology and reestablishes the link by activating the standby path. Spanning-Tree Protocol operation is transparent to end stations, which are unaware whether they are connected to a single LAN segment or a switched LAN of multiple segments. STP related parameters Priority : A value to identify the root bridge. ...

  • KTI Networks KS-2260 - page 25

    -25- Learning : The switch enters the Learning State if no path with a higher priority is found during the Listening State. Learned entries are entered in the Unicast Destination Forwarding T able. Normal data is not transmitted. Forwarding : The switch enters the Forwarding State after having been in the Learning State for a predefined time period ...

  • KTI Networks KS-2260 - page 26

    -26- 1.5.9 QoS Priority Function This switch supports two priority levels, high and low , and provides two priority functions: 1. Port-based Priority (Static priority) 2. 802.1p Priority (VLAN tagged priority) Priority Classification Methods Static priority is called port-based priority . The priority level of a receiv- ing packet is determined by ...

  • KTI Networks KS-2260 - page 27

    -27- 1.5.10 802.1X Port-Based Network Access Control For some IEEE 802 LAN environments, it is desirable to restrict access to the services offered by the LAN to those users and devices that are permitted to make use of those services. IEEE 802.1X Port-based network access control function provide a means of authenticating and authoriz- ing devices ...

  • KTI Networks KS-2260 - page 28

    -28- The 802.1X authenticator operates as a go-between with the supplicant and the authentication server to provide services to the network. When a switch is configured as an authenticator , the ports of the switch must then be configured for authorization. In an authenticator-initiated port authorization, a client is powered up or plugs into the p ...

  • KTI Networks KS-2260 - page 29

    -29- Enable 802.1X protocol Radius client configuration - Radius server IP : IP address of the Radius server Shared key : en encryption key for use during authentication sessions with the specified Radius server . It must match the key used on the Radius server . NAS identifier : identifier for this Radius client Server port : the UDP destination p ...

  • KTI Networks KS-2260 - page 30

    -30- 2. Installation and Management 2.1 Panel Description 2.2 AC Power Supply One AC power cord which meets the specification of your country of origin was supplied with the switch unit. Before installing AC power cord to the switch, make sure the AC power switch is in OFF position and the AC power to the power cord is turned off. The switch suppor ...

  • KTI Networks KS-2260 - page 31

    -31- 2.3 Network Switched Ports The switch provides three types of switched ports as follows: Port Number Label Specifications Por t T ype Modules Port 1 - 22 1 - 2 2 Fixed RJ-45 10/100TX No P or t 2 3 - 24 23 - 24 Fixed RJ-45 10/100TX N o F23 - F24 Module slot 100FX Optional Port 25-26 G 1 - G2 Module slot Gigabit Optional 2.3.1 10/100TX Ports The ...

  • KTI Networks KS-2260 - page 32

    -32- 2.3.2 100FX Modules Port 23 and Port 24 also provide optional fiber connectivity . The follow- ing installation rules should be applied: 100FX Module Installation W ork ing Connectors F23 Slot F24 Slot Port 23 Port 24 None None P23 RJ-45 P24 RJ-45 Installed None F23 module P24 RJ-45 can not be used None Installed P23 RJ-45 F24 module Installed ...

  • KTI Networks KS-2260 - page 33

    -33- The following 100FX modules are supported by F23 and F24 slots: Part Number Connector Cable Distance 2260-FMT Duplex ST MM F * 2 k m 2260-FMC Duplex SC M MF 2 k m 2260-FJM MT-RJ MM F 2 k m 2260-FVM V F-45 M M F 2 km 2260-FSA2 Duplex SC S MF* 2 0 km Note: * MMF - Multimode Fiber cable 50/125, 62.5/125 m m * SMF - Single Mode Fiber cable 8.7/125 ...

  • KTI Networks KS-2260 - page 34

    -34- 2.3.3 Gigabit Ports and Modules Port 25 and Port 26, labeled G1 and G2 respectively , support the following Gigabit modules: Part Number Connector Cable Distance 2260-GT RJ-45 Cat.5e 100m 2260-SXC Duplex SC MMF 62.5/125mm 220m MMF 50/125mm 500m 2260-SXL Duplex LC MMF 62.5/125mm 220m MMF 50/125mm 500m 2 26 0- LX C Duplex SC MMF 62.5/125mm 550m ...

  • KTI Networks KS-2260 - page 35

    -35- Specifications Part Number Compliance Speed Duplex 2260-GT IEEE 802.3ab 1000BASE-T 1000Mbps Half / Full IEEE 802.3u 100BASE-TX 100Mbps Half / Full IEEE 802.3 10BASE-T 10Mbps Half / Full Auto-negotiation function MDI-X RJ45 2260-SXC IEEE 802.3z 1000BASE-SX 1000Mbps Full 2260-SXL IEEE 802.3z 1000BASE-SX 1000Mbps Full 22 60 -LX C IEEE 802.3z 1000 ...

  • KTI Networks KS-2260 - page 36

    -36- 2.4 Rack Mounting T wo 19-inch rack mounting brackets are supplied with the switch for 19- inch rack mounting. The steps to mount the switch onto a 19-inch rack are: 1. Turn the power to the switch off. 2. Install two brackets with supplied screws onto the switch as shown in above figure: 2. Mount the switch onto 19-inch rack with rack screws ...

  • KTI Networks KS-2260 - page 37

    -37- 2.5 LED Indicators LED Name State Interpretation System LEDs P(Power) On Power is supplied to the unit. Off No power is supplied to the unit. C(Console) On Tx activities Off No Tx or Rx D(Diag) Blink D iagnostic and initialization in process O n Diagnostic and initialization completed Port 1 ~ Port 24 LEDs 100/10 O n Port speed is 100Mbps. Off ...

  • KTI Networks KS-2260 - page 38

    -38- 2.6 Cooling Fans The switch is equipped with two cooling fans. Both fans are featured with failure detection function. When the fan operation speed is below the specification, it is detected as a failure. The fan status can be moni- tored via management functions. One fan failure trap is also issued when fan failure event occurs. Important : D ...

  • KTI Networks KS-2260 - page 39

    -39- 2.7 Management Setup The managed switch is featured with management functions and can be managed by using the following methods: • Direct console connection over an RS-232 cable • T elnet software over TCP/IP network • SNMP manager software over TCP/IP network • W eb browser software from Internet or Intranet over TCP/IP network • SN ...

  • KTI Networks KS-2260 - page 40

    -40- 2.7.1 Setup for Out-of-band (Console) Management Before doing any in-band management, it is necessary to perform con- sole operation for configuring IP and SNMP related settings for the first time the switch is received for installation. Any PC running W indows 95/ 98/ or NT can be used as a console via COM port. W indows Hyper T erminal progr ...

  • KTI Networks KS-2260 - page 41

    -41- 2.7.2 Setup for In-band Management T o perform an in-band management, it is necessary to connect the sys- tem to your TCP/IP network. The steps are: 1. Configure IP and SNMP related settings to the device using direct console management when you receive it first time for the installa- tion. 2. Find a proper straight-through Category 5 UTP cabl ...

  • KTI Networks KS-2260 - page 42

    -42- 3. Console and T elnet Operation This chapter describes the detailed console operation. It can be applied to either out-of-band console management or in-band T elnet manage- ment. Refer to Chapter 2 for installation details. Cold Start When the power to the switch is turned on, the device start initialization and self-test process. The self-te ...

  • KTI Networks KS-2260 - page 43

    -43- Direct Console Management When you can see the self-test messages shown on screen properly , you can press <Enter> key to start console login operation. Go to Login Prompt section in next page directly . T elnet Management Use T elnet software to perform the management operation. The most convenient solution is using the built-in T elnet ...

  • KTI Networks KS-2260 - page 44

    -44- 3.1 Main Menu When login successfully , the main menu is shown as follows: --------------------------------------------- Main Menu Switch Static Configuration Protocol Related Configuration Status and Counters Reboot Switch TFTP Update Firmware Logout Configure the switch. Arrow/TAB/BKSPC = Move Item Enter= Select Item ------------------------ ...

  • KTI Networks KS-2260 - page 45

    -45- The following operation convention is commonly used for later configu- ration pages: Action menu: <Quit> Exit configuration <Edit> Edit each configuration value <Save> Save all configured values <Previous Page> Browse previous configuration page <Next Page> Browse next configuration page Control keys for action me ...

  • KTI Networks KS-2260 - page 46

    -46- 3.2 Switch Static Configuration [Switch Static Configuration] menu is shown as follows: ---------------------------------------------------- Managed 24+2G Switch : Switch Configuration Port Configuration Trunk Configuration VLAN Configuration Misc Configuration Administration Configuration Port Sniffer Configuration Priority Configuration MAC ...

  • KTI Networks KS-2260 - page 47

    -47- 3.2.1 Port Configuration The following page illustrates Port 1 ~ Port 8 configuration example: ------------------------------------------------------------------------- Managed 24+2G Switch : Port Configuration InRate OutRate FlowControl Port Type (100K) (100K) Enable Auto Spd/Dpx Full Half ----------------------------------------------------- ...

  • KTI Networks KS-2260 - page 48

    -48- Port : Port number Display names - POR T1 - POR T24, G1 - G2 Ty p e : Port type Display names - 100Tx, 100FX, 1000T , 1000FX InRate : Input (Ingress) rate control setting, 100Kbytes per unit. Options - 0 = disable rate control, 1 ~ 1000 valid rate value OutRate : Output (Egress) rate control setting, 100Kbytes per unit Options - 0 = disable ra ...

  • KTI Networks KS-2260 - page 49

    -49- 3.3.2 T runk Configuration Trunk configuration example page ------------------------------------------------------------------------- Managed 24+2G Switch : Trunk Configuration 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 G1 G2 1 V V V V - - - - - - - - - - - - - - - - - - - - - - 2 - - - - V V V V - - - - - - - - - ...

  • KTI Networks KS-2260 - page 50

    -50- 3.3.3 VLAN Configuration ---------------------------------------------------- Managed 24+2G Switch : VLAN Configuration VLAN Configure Create a VLAN Group Edit/Delete a VLAN Group Group Sorted Mode Previous Menu Configure the VLAN pvid and ingress.egress rules Tab=Next Item BackSpace=Previous Item Quit=Previous Menu Enter= Select Item -------- ...

  • KTI Networks KS-2260 - page 51

    -51- If 802.1Q mode is selected, some additional settings are required as follows: ---------------------------------------------------- Managed 24+2G Switch : VLAN Support Configuration VLAN Mode : 802.1Q IngressFilter1 IngressFilter2 Port PVID NonMember Drop Untagged Drop ------------------------------------------------------------------ PORT1 1 F ...

  • KTI Networks KS-2260 - page 52

    -52- 3.3.3.2 Create a VLAN Group Create a Port-based VLAN group ---------------------------------------------------- Add a VLAN Group VLAN Name: [ Vlan2 ] Grp ID:[ 2 ](1~4094) Port Member ----------------------- PORT1 Member PORT2 Member PORT3 No PORT4 No PORT5 No PORT6 No PORT7 No PORT8 No action-> <Quit> <Edit> <Save> <Pre ...

  • KTI Networks KS-2260 - page 53

    -53- Create an 802.1Q VLAN ---------------------------------------------------- Add a VLAN Group VLAN Name: [ Vlan2 ] VLAN ID:[ 2 ](1~4094) Protocol VLAN : None Port Member ----------------------- PORT1 UnTagged PORT2 Tagged PORT3 UnTagged PORT4 N o PORT5 N o PORT6 N o PORT7 N o PORT8 N o action-> <Quit> <Edit> <Save> <Previ ...

  • KTI Networks KS-2260 - page 54

    -54- Member : Give a member setting, Options - UnT agged : the specified port is a member port and outgoing frames are not tagged. T agged : the specified port is a member port and outgoing frames are tagged. No : the specified port is not a member port Note: If more than two VLAN groups are configured with same protocol value, make sure the member ...

  • KTI Networks KS-2260 - page 55

    -55- Example to edit Vlan2 group: ---------------------------------------------------- Edit a VLAN Group VLAN Name: [ Vlan2 ] VLAN ID:[ 2 ](1~4094) Protocol VLAN : AppleTalk/NetBIOS Port Member ----------------------- PORT1 UnTagged PORT2 Tagged PORT3 UnTagged PORT4 N o PORT5 N o PORT6 N o PORT7 N o PORT8 N o action-> <Quit> <Edit> & ...

  • KTI Networks KS-2260 - page 56

    -56- 3.3.4 Misc Configuration ---------------------------------------------------- Managed 24+2G Switch : Misc Configuration MAC Age Interval Broadcast Storm Filtering Max bridge transmit delay bound Port Security Collision Retry Forever Hash Algorithm Previous Menu Configure the MAC aging time Tab=Next Item BackSpace=Previous Item Quit=Previous Me ...

  • KTI Networks KS-2260 - page 57

    -57- 3.3.4.2 Broadcast Storm Filtering ---------------------------------------------------- Managed 24+2G Switch : Broadcast Storm Filter Mode Broadcast Storm Filter Mode : NO action-> <Edit> <Save> <Quit> ------------------------------------------------------------------ Tab=Next Item BackSpace=Previous Item Quit=Previous Menu ...

  • KTI Networks KS-2260 - page 58

    -58- 3.3.4.3 Max Bridge T ransmit Delay Bound ---------------------------------------------------- Managed 24+2G Switch : Max Bridge Transmit Delay Bound Max bridge transmit delay bound : OFF Low Queue Delay Bound : ENABLE Low Queue Max Delay Time : 2 5 5 (2ms/unit) action-> <Edit> <Save> <Quit> -------------------------------- ...

  • KTI Networks KS-2260 - page 59

    -59- 3.3.4.4 Port Security ---------------------------------------------------- Managed 24+2G Switch : Port Security Port Enable Security (disable MAC learning) ------------------------------------------------------------------ PORT1 Enabled PORT2 Enabled PORT3 Enabled PORT4 Disabled PORT5 Disabled PORT6 Disabled PORT7 Disabled PORT8 Disabled actio ...

  • KTI Networks KS-2260 - page 60

    -60- 3.3.4.5 Collision Retry Forever ---------------------------------------------------- Managed 24+2G Switch : Collision Retry Forever Collision Retry Forever : Enabled action-> <Edit> <Save> <Quit> ---------------------------------------------------- Collision Retry control setting for half duplex mode : Options - Enabled = ...

  • KTI Networks KS-2260 - page 61

    -61- 3.3.5 Administration Configuration ---------------------------------------------------- Managed 24+2G Switch : Device Configuration Change Username Change Password Device Information IP Configuration Previous Menu ---------------------------------------------------- 3.3.5.1 Change Username ---------------------------------------------------- M ...

  • KTI Networks KS-2260 - page 62

    -62- 3.3.5.2 Change Password ---------------------------------------------------- Managed 24+2G Switch : Password Configuration Old Password : xxxx New Password : xxxx enter again : xxxx action-> <Edit> <Save> <Quit> ---------------------------------------------------- The password is used together with UserName for login opera ...

  • KTI Networks KS-2260 - page 63

    -63- 3.3.5.4 IP Configuration ---------------------------------------------------- Managed 24+2G Switch : Device Configuration DHCP : Disabled IP Address : 192.168.0.2 Subnet Mask : 255.255.255.0 Gateway : 192.168.0.1 action-> <Edit> <Save> <Quit> ---------------------------------------------------- IP related parameters assign ...

  • KTI Networks KS-2260 - page 64

    -64- 3.3.6 Port Sniffer Configuration ---------------------------------------------------- Managed 24+2G Switch : Port Sniffer Sniffer Mode : Rx Sniffer Port : PORT1 Monitored Port: Port Member ---------------------- PORT1 - PORT2 - PORT3 V PORT4 - PORT5 V PORT6 - PORT7 - PORT8 - action-> <Quit> <Edit> <Save> <Previous Page& ...

  • KTI Networks KS-2260 - page 65

    -65- 3.3.7 Priority Configuration ---------------------------------------------------- Managed 24+2G Switch : The Priority Configuration Port Static Priority 802.1p Priority Previous Menu ---------------------------------------------------- T wo priority methods are provided: • Port Static Priority (Port-based Priority) • 802.1p Priority Note: ...

  • KTI Networks KS-2260 - page 66

    -66- 3.3.7.1 Static Priority ---------------------------------------------------- Managed 24+2G Switch : Port Priority Port Priority ---------------------- PORT1 Low PORT2 Low PORT3 High PORT4 High PORT5 Disable PORT6 Disable PORT7 Disable PORT8 Disable action-> <Quit> <Edit> <Save> <Previous Page> <Next Page> ----- ...

  • KTI Networks KS-2260 - page 67

    -67- 3.3.7.2 802.1p Priority ---------------------------------------------------- Managed 24+2G Switch : 802.1p Priority Configuration Priority 0 LOW Priority 1 LOW Priority 2 LOW Priority 3 LOW Priority 4 HIGH Priority 5 HIGH Priority 6 HIGH Priority 7 HIGH QoSMode : First Come First Service action-> <Quit> <Edit> <Save> ----- ...

  • KTI Networks KS-2260 - page 68

    -68- 3.3.8 MAC Address Configuration ---------------------------------------------------- Managed 24+2G Switch : MAC Address Configuration Static MAC Address Filtering MAC Address Previous Menu ---------------------------------------------------- 3.3.8.1 Static MAC Address ---------------------------------------------------- Managed 24+2G Switch : ...

  • KTI Networks KS-2260 - page 69

    -69- Add static MAC address ---------------------------------------------------- Managed 24+2G Switch : Add Static MAC Address MAC Address : 0040F6FE0005 Port Num : PORT3 Vlan ID : 2 action-> <Edit> <Save> <Quit> ---------------------------------------------------- MAC Address : the Ethernet MAC address Port Num : press <Spa ...

  • KTI Networks KS-2260 - page 70

    -70- 3.3.8.2 Filtering MAC Address Refer to Chapter 1 for description of MAC address filtering function. The operations to Add/Edit/Delete a filter MAC address are similar to the operations for static MAC address table. The following page shows an example of filter MAC address table: ---------------------------------------------------- MAC Address ...

  • KTI Networks KS-2260 - page 71

    -71- 3.4 Protocol Related Configuration ---------------------------------------------------- Managed 24+2G Switch : The Protocol Related Configuration STP SNMP GVRP IGMP LACP 802.1x Previous Menu ---------------------------------------------------- 3.4.1 STP ---------------------------------------------------- Managed 24+2G Switch : Spanning Tree P ...

  • KTI Networks KS-2260 - page 72

    -72- STP Enable ---------------------------------------------------- Managed 24+2G Switch : STP Enabled/Disabled Configuration STP : Enabled action-> <Edit> <Save> <Quit> ---------------------------------------------------- Spanning Tree function can be enabled or disabled. Press Space key to select enable or disable. System Co ...

  • KTI Networks KS-2260 - page 73

    -73- Current spanning tree information about the Root Bridge is shown on the left side and new values for STP parameters are configured on the right side. The settings are: Priority : The priority is assigned to the switch. The higher value is lower priority . Range: 0 - 65535 Max Age : The number of seconds a bridge waits without receiving Spannin ...

  • KTI Networks KS-2260 - page 74

    -74- Perport Configuration ---------------------------------------------------- Managed 24+2G Switch : STP Port Configuration Port PortSate PathCost Priority --------------------------------------------- PORT1 Forwarding 1 0 12 8 PORT2 Forwarding 1 0 12 8 PORT3 Forwarding 1 0 12 8 PORT4 Forwarding 1 0 12 8 PORT5 Forwarding 1 0 12 8 PORT6 Forwarding ...

  • KTI Networks KS-2260 - page 75

    -75- 3.4.2 SNMP ---------------------------------------------------- Managed 24+2G Switch : SNMP Protocol System Options Community Strings Trap Managers Previous Menu ---------------------------------------------------- Use this page to setup SNMP related parameters and SNMP trap hosts related parameters. 3.4.2.1 System Options -------------------- ...

  • KTI Networks KS-2260 - page 76

    -76- 3.4.2.2 Community Strings ---------------------------------------------------- Managed 24+2G Switch : SNMP Community Configuration Community Name Write Access --------------------------------------------- public Restricted private Unrestricted action-> <Add> <Edit> <Delete> <Save> <Quit> ----------------------- ...

  • KTI Networks KS-2260 - page 77

    -77- 3.4.2.3 T rap Managers A trap manager is a management station that allows to receive SNMP traps. An SNMP trap is issued by the switch when the associated trap event occurs in the switch. A trap manager is defined by its IP address and a community string. Up to three trap managers can be configured. --------------------------------------------- ...

  • KTI Networks KS-2260 - page 78

    -78- 3.4.3 GVRP This page you can enable or disable the GVRP (GARP VLAN Registra- tion Protocol) support. ---------------------------------------------------- Managed 24+2G Switch : GVRP Configuration GVRP : Enabled action-> <Edit> <Save> <Quit> ---------------------------------------------------- Options - Enabled, Disabled 3. ...

  • KTI Networks KS-2260 - page 79

    -79- 3.4.5 LACP This menu list is used to configure LACP trunk groups. ---------------------------------------------------- Managed 24+2G Switch : LACP Configuration Working Ports Setting State Activity LACP Status Previous Menu ---------------------------------------------------- 3.4.5.1 Working Port Setting --------------------------------------- ...

  • KTI Networks KS-2260 - page 80

    -80- 3.4.5.2 State Activity ------------------------------------------------------------------------- Managed 24+2G Switch : LACP Port Active State Configuration Port State Activity Port State Activity ---------------------------- ----------------------------- 1 Active 1 4 Passive 2 Active 1 5 Passive 3 Active 1 6 Passive 4 Active 1 7 Passive 5 Pas ...

  • KTI Networks KS-2260 - page 81

    -81- 3.4.5.3 LACP Status ---------------------------------------------------- Managed 24+2G Switch : LACP Group Status Group Key : 1 Port_No : 1 2 3 4 action-> <Quit> <Previous Page> <Next Page> ---------------------------------------------------- This page shows LACP status of each trunk group. 3.4.6 802.1X ------------------- ...

  • KTI Networks KS-2260 - page 82

    -82- 3.4.6.1 Enable 802.1X Protocol ---------------------------------------------------- Managed 24+2G Switch : 802.1x Enabled/Disabled Configuration 802.1x : Enabled action-> <Edit> <Save> <Quit> ---------------------------------------------------- This menu is used to enable 802.1X function of the switch. 3.4.6.2 802.1X Syste ...

  • KTI Networks KS-2260 - page 83

    -83- 3.4.6.3 802.1X Per Port Configuration ---------------------------------------------------- Managed 24+2G Switch : 802.1x Port Status (Force Unauth= Fu, Force Au=Fa, Auto=Au, None=No) Port Status ------------------- PORT1 N o PORT2 N o PORT3 N o PORT4 N o PORT5 N o PORT6 N o PORT7 N o PORT8 N o action-> <Quit> <Edit> <Save> ...

  • KTI Networks KS-2260 - page 84

    -84- 3.4.6.4 802.1X Misc. Configuration ---------------------------------------------------- Managed 24+2G Switch : 802.1x Misc Configuration Quiet-period <0..65535, default=60> : 60 Tx-period <0..65535, default=30> : 30 Supplicant-timeout <0..300, default=30> : 30 Server-timeout <0..300, default=30> : 30 ReAuthMax <1..10 ...

  • KTI Networks KS-2260 - page 85

    -85- 3.5 Status and Counters ---------------------------------------------------- Managed 24+2G Switch : Status and Counters Port Status Port Counters System Information Previous Menu ---------------------------------------------------- Menu functions: Port Status : display the status of all switched ports and trunk groups. Port Counters : display ...

  • KTI Networks KS-2260 - page 86

    -86- 3.5.1 Port Status ------------------------------------------------------------------------- Managed 24+2G Switch : Port Configuration Link InRate OutRate Flow Port Status (100K) (100K) Enable Auto Spd/Dpx Control ------------------------------------------------------------------ PORT1 Down 0 0 No AUTO 100 Full On PORT2 Down 0 0 No AUTO 100 Ful ...

  • KTI Networks KS-2260 - page 87

    -87- 3.5.2 Port Counters ------------------------------------------------------------------------- Managed 24+2G Switch : Port Counters Port TxGoodPkt TxBadPkt RxGoodPkt RxBadPkt TxAbort Collision DropPkt --------------------------------------------------------------------------- PORT1 0 0 0 0 0 0 0 PORT2 0 0 0 0 0 0 0 PORT3 0 0 0 0 0 0 0 PORT4 0 0 ...

  • KTI Networks KS-2260 - page 88

    -88- 3.5.3 System Information ---------------------------------------------------- Managed 24+2G Switch : System Information MAC Address : 0040F6FE0005 Firmware version : x .x ASIC version : x.xx PCBA version : x.xx G1 Module Type : N/A [N/A ] G2 Module Type : N/A [N/A ] F23 Module Type : N/A [N /A ] F24 Module Type : N/A [N /A ] FAN-1 Status : Nor ...

  • KTI Networks KS-2260 - page 89

    -89- 3.6 Reboot Switch ---------------------------------------------------- Managed 24+2G Switch : Restart Configuration Restart Default Previous Menu ---------------------------------------------------- 3.6.1 Restart This command will reboot the switch with current configuration setting values. Confirmation prompt is: ----------------------------- ...

  • KTI Networks KS-2260 - page 90

    -90- 3.7 TFTP Update Firmware ---------------------------------------------------- Managed 24+2G Switch : TFTP Update Firmware Configuration TFTP Update Firmware TFTP Restore Configuration TFTP Backup Configuration Previous Menu ---------------------------------------------------- This menu supports : TFTP Update Firmware : Update the switch firmwa ...

  • KTI Networks KS-2260 - page 91

    -91- 3.7.1 TFTP Update Firmware ---------------------------------------------------- Managed 24+2G Switch : TFTP Update Firmware TFTP Server : 192.168.0.15 Remote File Name : image.bin action-> <Edit> <Save> <Quit> ---------------------------------------------------- The steps to use TFTP to update switch firmware are: 1. Start ...

  • KTI Networks KS-2260 - page 92

    -92- 3.7.2 TFTP Restore Configuration ---------------------------------------------------- Managed 24+2G Switch :Restore Configuration File TFTP Server : 192.168.0.15 Remote File Name : data.dat action-> <Edit> <Save> <Quit> ---------------------------------------------------- The steps to use TFTP to restore switch configurati ...

  • KTI Networks KS-2260 - page 93

    -93- 3.7.3 TFTP Backup Configuration ---------------------------------------------------- Managed 24+2G Switch :Upload Configuration File TFTP Server : 192.168.0.15 Remote File Name : newdata.dat action-> <Edit> <Save> <Quit> ---------------------------------------------------- T o use TFTP to upload current switch configuratio ...

  • KTI Networks KS-2260 - page 94

    -94- 4. SNMP Management SNMP management are performed at a network management station run- ning SNMP network management application manager software. The following figure illustrates an example model: The switch unit serves as an SNMP agent and provides the capabilities that allows network administrators via SNMP protocol to set parameters and view ...

  • KTI Networks KS-2260 - page 95

    -95- 4 . 1 Configuring SNMP Settings via Console Operation Before performing SNMP operation, proper SNMP settings must be con- figured. The SNMP related settings are: Name : Logic name to identify the switch unit Location : Location where the switch unit is installed Contact : Contact person regarding the switch unit Community string : SNMP communi ...

  • KTI Networks KS-2260 - page 96

    -96- The following MIB-2 objects are related to the switched ports and are indexed by a port number 1 ~ 27 (27 = CPU port): Port MIB-2 Objects Set/Get V alue Options ifIndex.1 ~ 27 Ge t Physical port number ifDescr .1 ~ 26 Ge t text - Port 1~26 on unit 1 ifDescr .27 G et text - ethernet switch low driver ifT ype.1 ~ 27 Get erhernet-csmacd(6) ifSpee ...

  • KTI Networks KS-2260 - page 97

    -97- The following are device-related private MIB objects: Private MIB Objects Set/Get V alue Options DeviceName.0 G e t KS2260 PortNumber .0 G et 2 6 F23_Module.0 Ge t N/A(0) FX_Module(1) F23_Module.0 Ge t N/A(0) FX_Module(1) G1_Module.0 Ge t N/A(0) TP_10/100/1000T(1) FX_1000SX_SC(2) FX_1000SX_LC(3) FX_1000LX_SC(4) FX_1000LX_SC(5) FX_1000LX_SC(6) ...

  • KTI Networks KS-2260 - page 98

    -98- 4.3 SNMP T raps The switch supports the following SNMP traps. When the trap event occurs, the SNMP agent will generate a trap notification to SNMP trap manager stations. Up to three trap managers can be supported. Each trap manager must be configured with : IP address and Community string which the trap manager belongs. The provided traps and ...

  • KTI Networks KS-2260 - page 99

    -99- 5. Web Management The managed switch features an http server which can serve the man- agement requests coming from any web browser software over internet or intranet network. W eb Browser Microsoft Internet Explorer 5.0 or later Important: The switch does not support any version of Netscape browser software. Best Display Resolution 1024 x 768 ...

  • KTI Networks KS-2260 - page 100

    -100- 5.1 Start Browser Software and Making Connection Start your browser software and enter the IP address of the device unit to which you want to connect. The IP address is used as URL for the browser software to search the device. URL : http://xxx.xxx.xxx.xxx/ Factory default IP address : 192.168.0.2 Login the Username and Password to enter web ...

  • KTI Networks KS-2260 - page 101

    -101- 5.2 Web Management Home Overview This page provides the following menu list. Each menu is described individually in the following sections. • Menu • Port Status • Port Statistics • Administrator • TFTP Update Firmware • Configuration Backup • Reset System • Reboot ...

  • KTI Networks KS-2260 - page 102

    -102- 5.3 Port status This page shows all port status in a scroll bar list. The status are depen- dent on user settings and the negotiation results as follows: State : Display port function status including - Config : function setting - On = enable, Off = disable Atual : status - On = enabled, Off = disabled Link Status : Down = No Link, UP = activ ...

  • KTI Networks KS-2260 - page 103

    -103- Auto Negotiation : Display the auto negotiation mode setting and status Config / Atual Auto = enable auto negotiation with the specified highest capability Force = disable auto negotiation and use forced mode Nway-force = enable auto negotiation with the specified capability Note : Specified capability means speed and duplex configuration Spe ...

  • KTI Networks KS-2260 - page 104

    -104- 5.4 Port Statistics This page displays the function, link status, and statistic counters of all ports by a scroll list. The status and counters are: State : On = port is enabled, Off = port is disabled Link : port link status, Down = link down, Up = link up TxGoodPkt : Good transmitted packet count TxBadPkt : Bad transmitted packet count RxGo ...

  • KTI Networks KS-2260 - page 105

    -105- Click port icons on the switch image to also see a single port counters as follows: 5.5 Administrator Administrator menu provides the following management functions: • IP address • Switch settings • Console port information • Port controls • Trunking • Filter database • VLAN configuration • Spanning tree • Port Sniffer • S ...

  • KTI Networks KS-2260 - page 106

    -106- 5.5.1 IP Address A vailable settings: DHCP : DHCP function setting Enable : enable DHCP client function to get dynamic IP address Disable : disable DHCP client function and use static IP address IP Address : Static IP address assigned to the managed switch unit Subnet_Mask : subnet mask setting Gateway : Default gateway IP address Click Butto ...

  • KTI Networks KS-2260 - page 107

    -107- 5.5.2 Switch Setting This menu provides the following functions: Basic : the basic information of the managed switch unit Module Info : the information of the Gigabit modules installed Advanced : some switch related settings 5.5.2.1 Basic Information Description : The name of switch type MAC Address : The unique MAC address assigned to the sw ...

  • KTI Networks KS-2260 - page 108

    -108- 5.5.2.2 Module Info Module information of Port 23 F23 slot, Port 24 F24 slot, G1 port, and G2 port : TYPE : The type of the module installed in port slot DESCRIPTION : The description about the installed module ...

  • KTI Networks KS-2260 - page 109

    -109- 5.5.2.3 Advanced Miscellaneous settings : MAC Address Age-out T ime : T ype the number of seconds that an inactive MAC address remains in the switch address table. The valid range is 300~765 seconds (must be multiple of 3). Default is 300 seconds. Max bridge transmit delay bound control : Limit the packets queuing time in switch. If enabled a ...

  • KTI Networks KS-2260 - page 110

    -110- Enable Low Queue Delay Bound : setting to limit the low priority packets queuing time in switch. If enabled and queuing time expired, the low priority packets queued in switch will be sent. Note: Make sure Max bridge transit delay bound control is enabled when Low Queue Delay Bound control is set to ENABLE. Max. Delay Time : max. low queuing ...

  • KTI Networks KS-2260 - page 111

    -111- Priority Queue Service settings (select one of the following three modes): First Come First Service : The sending sequence is based on the or- der that packets arrived. All High before Low : The high priority packets sent before low priority packets. WRR : W eighted Round Robin. Select the ratio preference for high prior- ity packets vs. low ...

  • KTI Networks KS-2260 - page 112

    -112- 5.5.3 Console Port Information Console port configuration: Baudrate(bits/sec) : Fixed baud rate - 9600 Data bits : 8 Parity Check : none Stop Bits : 1 Flow control : none ...

  • KTI Networks KS-2260 - page 113

    -113- 5.5.4 Port Controls This page allows to change per port configuration settings as follows: Port : Select the ports to perform setup. More than one port can be selected at the same time for setup. See next page for control settings. Note: All default values displayed for setup are not current setting values, but the factory default values inst ...

  • KTI Networks KS-2260 - page 114

    -114- Control settings: State : Disable or enable this port function. Auto Negotiation : Set auto negotiation mode for this port, options - Auto = enable auto negotiation with the highest capability Nway = enable auto negotiation with the specified capability Force = disable auto negotiation and use forced mode Speed : Set speed for this port (the ...

  • KTI Networks KS-2260 - page 115

    -115- 5.5.5 T runking This page shows settings and status of trunking function. Refer to Chap- ter 1 fo r the description of LACP trunking function. ...

  • KTI Networks KS-2260 - page 116

    -116- 5.5.5.1 Aggregator settings System Priority : A value used to identify the priority between two active LACP link partners. The switch with the lowest value has the highest priority and is selected as the active LACP . Group ID : There are seven trunk groups are supported to be configured. Choose the [Group ID] and click [Get] to get current s ...

  • KTI Networks KS-2260 - page 117

    -117- 5.5.5.2 Aggregator Information The following pages illustrate three examples: No active group configured. ...

  • KTI Networks KS-2260 - page 118

    -118- T wo Static Trunking groups are configured. ...

  • KTI Networks KS-2260 - page 119

    -119- One LACP trunk group is formed. Trunking information between Actor and Partner are shown. ...

  • KTI Networks KS-2260 - page 120

    -120- 5.5.5.3 State Activity Per port LACP mode: Active (select ) : The port can start LACP negotiation with its link partner by sending LACP protocol packet automatically . Passive (not select ) : The port does not send LACP protocol packets automatically and responds only if it receives LACP packets from its link partner . Click Button: [ Apply ] ...

  • KTI Networks KS-2260 - page 121

    -121- 5.5.6 Forwarding and Filtering Database 5.5.6.1 IGMP Snooping Control setting: IGMP Protocol : enable IGMP function to collect IP multicast data base and perform IP multicast operation Multicast Group Information: This page displays the IGMP snooping information. IP multicast ad- dresses range from 224.0.0.0 through 239.255.255.255. IP addres ...

  • KTI Networks KS-2260 - page 122

    -122- 5.5.6.2 Static MAC Address This page is used to maintain Static MAC address data base. Refer to Chapter 1 for the description of Static MAC address function. Static MAC address related settings: Mac Address : Static Ethernet MAC address (12 digits) Port num : The port number where the MAC address is located Vlan ID : The associated Vlan ID to ...

  • KTI Networks KS-2260 - page 123

    -123- 5.5.6.3 MAC Address Filtering This page is used to maintain filter MAC address table. MAC address filtering allows the switch to drop unwanted traffic. Traffic is filtered based on the destination addresses (DAs). Refer to chapter 1 for the function description. Filter MAC address settings: Mac Address : The destination MAC address to be filt ...

  • KTI Networks KS-2260 - page 124

    -124- 5.5.7 VLAN configuration The switch supports port-based, 802.1Q (tag-based) and protocol-base VLAN in this page. In the default configuration, VLAN support is dis- able. Refer to Chapter 1 for more description about VLAN function. VLAN mode selection: No VLAN - VLAN is disabled Port Based VLAN 802.1Q - 802.1Q VLAN with Protocol classification ...

  • KTI Networks KS-2260 - page 125

    -125- 5.5.7.1 Port-based VLAN Click : [ Add ] : to create a new VLAN group [ Edit ] : to edit an existing VLAN group [ Delete ] : to delete a VLAN group [ PrPage ] : to browse previous group page [ NextPage ] : to browse next group page ...

  • KTI Networks KS-2260 - page 126

    -126- A Port-based VLAN group contains the following settings: VLAN name : Name of the VLAN group Group ID : Unique ID for the group Member ports : list of ports belonging to the group ID Click [Apply] to confirm the changes. Note: If the trunk groups exist, you can see it (ex:TRK1,TRK2…..) in select menu of ports, and you can configure it as the ...

  • KTI Networks KS-2260 - page 127

    -127- 5.5.7.2 802.1Q VLAN This page is used to display current configured T ag-based VLAN, create a new VLAN, and enable or disable GVRP protocol. Up to 256 VLANs can be configured. When enabling 802.1Q VLAN, all ports on the switch belong to default Vlan ID 1. The default VLAN can not be deleted. GVRP (GARP VLAN Registration Protocol) support can ...

  • KTI Networks KS-2260 - page 128

    -128- Add a new VLAN Basic page settings: VLAN Name : name for the new VLAN VID : VLAN ID of the new VLAN (value: 2-4094, default: 1) Protocol Vlan : setting for protocol support as follows: None IP , ARP , AppleT alk/NetBIOS Novell_IPX, Banyan_V ines_C4 / Novell IPX(raw Ethernet) Banyan_V ines_C5 / Spanning_T ree_Protocol_BPDU Banyan_V ines_AD / N ...

  • KTI Networks KS-2260 - page 129

    -129- Edit member ports : select member ports from available port box [ Add ] - add one member port [ Remove ] - remove a member port Click [ Next ] : to set tag/untag mode for the member ports Note: If more than two VLAN groups are configured with same protocol value, make sure the member ports of those groups are not overlapping. T ag : outgoing ...

  • KTI Networks KS-2260 - page 130

    -130- Port VID Settings Click [ Port VID ] to set per port VID and Ingress filtering rules. Multiple port selection at the same time for same settings is allowed. Port VID Settings: Port VID (PVID) : the port VLAN ID that will be assigned to untagged traffic on a given port. The range is 1~255, default PVID is 1. Ingress Filtering Rule 1 : Drop or ...

  • KTI Networks KS-2260 - page 131

    -131- 5.5.8 Spanning T ree This page shows an example of STP Root Bridge information of the switch. ...

  • KTI Networks KS-2260 - page 132

    -132- This page shows an example of STP port status Refer to Chapter 1 for the description of Spanning Tree Protocol. ...

  • KTI Networks KS-2260 - page 133

    -133- STP parameters settings: STP State : Enable or disable STP function Priority : A value used to identify the root bridge. The bridge with the lowest value has the highest priority and is selected as the root. V alid values : 1 through 65535. Max Age : The number of seconds a bridge waits without receiving Spanning-Tree Protocol configuration m ...

  • KTI Networks KS-2260 - page 134

    -134- STP port parameters settings: Port Priority : Priority value for becoming the root port. The rage is 0- 255, default setting is 128, the lowest number has the highest priority . Path Cost : Specifies the path cost of the port that switch uses to deter- mine which port are the forwarding ports the lowest number is forward- ing ports, the rage ...

  • KTI Networks KS-2260 - page 135

    -135- 5.5.9 Port Sniffer Sniffer Mode : Select one of sniffer modes, options - DISABLE : Disable sniffer function RX : All Rx traffic on monitored ports are copied to Analysis port TX : All Tx traffic on monitored ports are copied to Analysis port BOTH : Both Rx and Tx traffic are copied to Analysis port Sniffer Port : The port can be used to see a ...

  • KTI Networks KS-2260 - page 136

    -136- 5.5.10 SNMP SNMP Parameters This page is used to configure SNMP related parameters as follows: Name : Name to be used for the switch. Location : The location of the switch. Contact : A name of a person or organization Click [Apply] to apply the settings. ...

  • KTI Networks KS-2260 - page 137

    -137- SNMP Managers Community String and access control settings: Community String : The community string serves as a password which allows remote SNMP manager stations to access the switch management objects via SNMP protocol. Max. Up to 4 community strings are sup- ported. RO : Access right for Read Only is associated to the community string RW : ...

  • KTI Networks KS-2260 - page 138

    -138- SNMP T rap Managers A trap manager is a management station which can receive SNMP trap messages sent by the switch when predefined trap events occur . SNMP Trap Manager settings: IP address : IP address of the trap manager station Community : Community string belonging to the trap manager Click Buttons: [ Add ] to add a new trap manager [ Rem ...

  • KTI Networks KS-2260 - page 139

    -139- 5.5.1 1 Security Manager This page is used to configure the user who is allowed to access the switch via direct console, telnet and web management interfaces. User name : T ype the new user name Assign/Change password : T ype the new password Reconfirm password : Retype the new password Click [ Apply ] to apply the changes. ...

  • KTI Networks KS-2260 - page 140

    -140- 5.5.12 802.1X Configuration This menu includes three 802.1X function related settings: System Configuration : Parameters for connection to a Radius server PerPort Configuration : Per port 802.1X mode settings Misc Configuration : 802.1X protocol related timers and parameters ...

  • KTI Networks KS-2260 - page 141

    -141- System Configuration Radius Server IP : IP address of the Radius server Server Port : the UDP destination port for authentication requests to the specified Radius server Accounting Port : the UDP destination port for accounting requests to the specified Radius server Shared Key : an encryption key for use during authentication sessions with t ...

  • KTI Networks KS-2260 - page 142

    -142- 5.5.12.1 802.1X PerPort Configuration This page is used to set per port 802.1x authorization state mode. The options are: Au (Auto) - The port is set to the Authorized or Unauthorized state in accordance with the outcome of an authentication exchange between the Supplicant and the Authentication Server . Fa (Forced Authorized) - The port is f ...

  • KTI Networks KS-2260 - page 143

    -143- 5.5.12.2 802.1X Misc Configuration This page is used to setup 802.1x protocol timers and parameters: Quiet period - the period during which the port does not try to acquire a supplicant (unit: second) Tx period - the period the port waits to retransmit the NEXT EAPOL PDU during an authentication session (unit: second) Supplicant timeout - the ...

  • KTI Networks KS-2260 - page 144

    -144- 5.6 TFTP Update Firmware The steps to update the firmware of the switch are: 1. Start your TFTP server . 2. Copy the firmware image file of new version into the TFTP server . 3. In this web page, specify the IP address of the TFTP server , in where the new firmware image file is stored. 4. In this page, specify Firmware File Name of the new i ...

  • KTI Networks KS-2260 - page 145

    -145- 6. Click [ Update Firmware ] in following download complete message to confirm the update. 7. Reboot the system ...

  • KTI Networks KS-2260 - page 146

    -146- 5.7 Configuration Backup 5.7.1 TFTP Restore Configuration The function is used to download a new default configuration file from a TFTP server into the switch. The steps are: 1. Start your TFTP server . 2. Copy the new default configuration file into the TFTP server . 3. In this web page, specify the IP address of the TFTP server , in where t ...

  • KTI Networks KS-2260 - page 147

    -147- 5.7.2 TFTP Backup Configuration This function is used to backup (upload) current configuration settings of the switch unit onto a TFTP server . The steps are: 1. Start your TFTP server . 2. In this web page, specify the IP address of the TFTP server , to where the current configuration data is saved. 3. Specify Backup File Name of the configu ...

  • KTI Networks KS-2260 - page 148

    -148- 5.8 Reset System This function is used to reset the switch with default configuration data. Click [ Reset ] to start the operation. ...

  • KTI Networks KS-2260 - page 149

    -149- 5.9 Reboot This function is used to reboot the switch with current configuration settings. Click [ Reboot ] to start operation. ...

  • KTI Networks KS-2260 - page 150

    -150- 6. Update Firmware from Console The switch also supports firmware update from console port. The operation is performed over 1K Xmodem protocol. Cases to update firmware from console: 1. Power on the switch and press any key from console within 5 seconds. The switch enters 1K Xmodem receiver mode. 2. The switch enters 1K Xmodem receiver mode a ...

  • KTI Networks KS-2260 - page 151

    -151- Appendix A: Factory Default Settings IP Address Related Settings DHCP D i s a b l e d Static IP Address 192.168.0.2 Subnet Mask 255.255.255.0 Default Gateway 192.168.0.1 Per Port Settings Port Function Enabled Auto-negotiation Au t o Speed 100Mbps (Port 1-Port 24) 1000Mbps (Port G1, G2) Duplex Full (All ports) Flow Control / Full Enabled Flow ...

  • KTI Networks KS-2260 - page 152

    -152- QoS Priority Settings Port Priority Disabled ( All ports ) 802.1p Priority Level Low priority for Level 0~3 High priority for Level 4-7 Priority Queue Service Mode All High before Low VLAN Settings VLAN Mode No VLAN Port-based VLAN No group (if enabled) 802.1Q VLAN GVRP enabled 802.1Q VLAN Groups All ports in VID=1 Vlan Name=Default T ag rule ...

  • KTI Networks KS-2260 - page 153

    -153- 802.1X Function Settings 802.1X Protocol Di sab led Radius Server IP 192.168.0.59 Shared Key 12345678 NAS Identifier NAS_L2_SWITCH Server Port 1812 Accounting Port 1813 Port 802.1x mode None (no control) for all ports Quiet Period 60 seconds Tx Period 30 s econds Supplicant Timeout 30 seconds Server Timeout 30 seconds Max Requests 2 times ReA ...

Fabbricante KTI Networks Categoria Switch

I documenti che otteniamo dal fabbricante del dispositivoKTI Networks KS-2260 possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici KTI Networks
- manuali per l’uso KS-2260
- schede prodotto KTI Networks
- opuscoli
- o etichette energetiche KTI Networks KS-2260
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso KTI Networks KS-2260.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione KTI Networks KS-2260, manuali di manutenzione, brevi manuali o manuali utente KTI Networks KS-2260. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto KTI Networks KS-2260.

Manuali per l’uso simili

Manuale completo del dispositivo KTI Networks KS-2260, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare KTI Networks KS-2260 dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti KTI Networks KS-2260.

Il manuale per l’uso completo KTI Networks, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale KTI Networks KS-2260 - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice KTI Networks KS-2260, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per KTI Networks KS-2260 che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo KTI Networks KS-2260 - che ci dovrebbe aiutare nei primi passi durante l'uso KTI Networks KS-2260
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del KTI Networks KS-2260
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio KTI Networks KS-2260 in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su KTI Networks KS-2260?

Utilizza il modulo sottostante

Se non hai risolto il problema con KTI Networks KS-2260 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con KTI Networks KS-2260 è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)