-
Hanns.G HW216 - page 1
22 inch W ide Scr een TFT LCD Monitor HW216 USER’S MANUAL ...
-
Hanns.G HW216 - page 2
User ’s M a nual 2 Before operating the monitor , please read this manual thoroughly . This manual should be retained for future reference. FCC Class B Radio Frequenc y Interference St atement This equipment has been tested and found to comp ly with the limit s for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are d ...
-
Hanns.G HW216 - page 3
User ’s M anual Congratulations! The display you have just purchased carries the TCO’03 Displays label. This means that your display is designed, manufactured and tested according to some of the strictest quality and environmental requirement s in the world. This makes for a high performance product, des igned with the user in focus that also m ...
-
Hanns.G HW216 - page 4
User ’s M a nual 4 Recycling Information We, Hanns.G, care very much about our environment protection strategy and firmly believe that it helps us have healthier earth via appr opriate treatment and recycling of industrial technology devices at the end-of-life. These devices contain recyclable materials, which can be re-decom posed and re-integra ...
-
Hanns.G HW216 - page 5
User ’s M anual 5 T ABLE OF CONTENTS SAFETY NOTICE ..................................................................................................................6 PRECAUTIONS .............................................................................................................6 SPECIAL NOTES ON LCD MONIT ORS ........................... ...
-
Hanns.G HW216 - page 6
User ’s M a nual 6 SAFETY NOTICE 1. The changes or modifications not expr essly approved by the party responsible for compliance could void the user's authority to operate the equipment. 2. Shielded interface cables and AC power cord, if any , must be used in order to comply with the emission limits. 3. The manufacturer is not responsible fo ...
-
Hanns.G HW216 - page 7
User ’s M anual SPECIAL NOTES ON LCD MONIT O RS The following symptoms are normal with LCD monitor and do not indicate a problem. Due to the nature of the fluorescent light, the screen may flicker during initial use. T urn off the Power Switch and then turn it on agai n to make sure the flicker disappears. Y ou may find slightly uneven br ...
-
Hanns.G HW216 - page 8
User ’s M a nual 8 BEFORE YOU OPERA TE THE MONITOR FEA TURES 22” Wide screen TFT Color LCD Monitor Crisp, Clear Display for Windows Recommended Resolutions : 1680 X 1050 @60Hz EP A ENERGY ST AR ® Ergonomic Design S p ace Saving, Compact Case Design CHECKING THE CONTEN TS OF THE P ACKAGE The product package should includ ...
-
Hanns.G HW216 - page 9
User ’s M anual INST ALLA TION INSTRUCTIONS Inst all Remove Figure 1: Installing a nd Removing the Base INSTALLATION: 1. Align the monitor with the opening in the base. 2. Note that the longer secti on of the base points forward. 3. Snap the monitor into its base. A clear c lick sound will affirm that the base is connected correctly. 4. Verify th ...
-
Hanns.G HW216 - page 10
User ’s M a nual 10 MAKING CONNECTIONS CONNECTING TO A PC: T urn off your computer befor e performing the step s below . 1. Connect one end of the D-Sub cable to t he back of the monitor and connect the other end to the computer ’ s D-Sub port. 2. Connect one end of the DVI-D cable (Dual input mode optional) to the back of the monitor and conne ...
-
Hanns.G HW216 - page 11
User ’s M anual CONNECTING TO A A/V DEVICE: Connect A/V devices v ia the DVI and Audio Line in connectors at the back of the monitor . 1. Connect the Y (green) connector on the DVI- I to YPbPr adapter cable to the Y output connector on the A/V device. 2. Connect the Pb (blue) connector on the DV I-I to YPbPr adapter cable to the Pb/Cb output conn ...
-
Hanns.G HW216 - page 12
User ’s M a nual 12 ADJUSTING THE VIEWING ANGLE 1. For optimal viewing it is recommended to look at the full face of the monitor , then adjust the monitor ’s angle to your own preference. 2. Hold the stand so you do not topple the monitor when you change the monitor’s angle. 3. Y ou are able to adjust the monitor’s angle from 0 ° to 20 ° ...
-
Hanns.G HW216 - page 13
User ’s M anual OPERA TING INSTRUCTIONS GENERAL INSTRUCTIONS Press the power button to turn the monitor on or of f. The other control buttons are located on the front panel of the monitor (See Figure 5) . By changing these settings, the picture can be adjusted to your personal preferences. The power cord should be connected. Connect the S ...
-
Hanns.G HW216 - page 14
User ’s M a nual 14 CONTROL P ANEL BUTTON FUNCTIONS Power Button: Press this button to switch ON/OFF of monitor ’ s power . Power Indicator: Green — Power On mode. Orange — Power Saving mode. MENU / ENTER: 1. Activates the OSD menu or confirms adjustments to settings. 2. Exit OSD volume display when in volume OSD status. Vo ...
-
Hanns.G HW216 - page 15
User ’s M anual HOW TO ADJUST A SETTI NG M M a a i i n n M M e e n n u u FUNCTION DESCRIPTION Brightness Select the 「 Brightness 」 option on the 「 Main Menu 」 . Enter the option by pressing the 「 Menu 」 button again, and adjust the level. Contrast Select the 「 Contrast 」 option on the 「 Main Menu 」 . Enter the option by pressi ...
-
Hanns.G HW216 - page 16
User ’s M a nual 16 V - position Select the 「 V -position 」 option to shift the screen image up or down. Enter the option and adjust the level. Clock Adjustment Select the 「 Clock Adjustment 」 option to reduce the vertical flicker of characters on the screen. Enter the option and adjust the level. Phase Adjustment Select the 「 Phase Adj ...
-
Hanns.G HW216 - page 17
User ’s M anual Exit Exit the OSD menu function. O O S S D D S S e e t t t t i i n n g g FUNCTION DESCRIPTION OSD H-Position Select the 「 OSD H-Position 」 option to adjust the horizontal position of the OSD. Enter the option and adjust the level. OSD V - position Select the 「 OSD V -Position 」 option to adjust the vert ical position of th ...
-
Hanns.G HW216 - page 18
User ’s M a nual 18 DOS mode Select the 「 DOS mode 」 option to set the monito r for use with PC. Enter the option and select 720 × 400 or 640 × 400. Factory Reset Select the 「 Factory Reset 」 option to reset to the monitor ’s default setting. This will erase the current settings. En ter the option and se lect On or Of f. Exit Exit the ...
-
Hanns.G HW216 - page 19
User ’s M anual 19 TECHNICAL SUPPORT (F AQ) Q & A FOR GENERAL PROBLEMS PROBLEM & QUESTION POSSIBLE SOLUTION Power LED is not on Check if the Power Switch is in the ON position Power Cord should be connected No Plug & Play Check if the PC system is Plug & Play compatible Check if the Vi deo Card is Plug & Play c ...
-
Hanns.G HW216 - page 20
User ’s M a nual 20 ERROR MESSAGE & PO SSIBLE SOLUTIONS CABLE NOT CONNECTED : 1. Check that the signal-cable is properly c onnected, If the connector is loose, tighten the connector ’ s screws. 2. Check the signal-cable’ s connection pins for damage. INPUT NOT SUPPORT : Y our computer has been set to unsuitable di splay mode, set ...
-
Hanns.G HW216 - page 21
User ’s M anual 21 APPENDIX SPEC IFICA TIONS Driving system TFT Color LCD LCD Panel Size 22" (21.6” viewable) Pixel pitch 0.276mm(H) x 0.276mm(V) H-Frequency 30KHz – 80KHz V ideo V -Frequency 50 – 75Hz Display Colors 16.7M Colors Maximum Screen Size Hor . :464.94mm V er . :290.58mm Max. Resolution WSXGA+ 1680 x 1050 @75Hz Plug & Pl ...
Hai una domanda su Hanns.G HW216?
Utilizza il modulo sottostante
Se non hai risolto il problema con Hanns.G HW216 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Hanns.G HW216 è probabile che voglia condividere il modo di risolverlo.