-
Zenoah SRTZ2610F - page 1
GB-1 G B SRTZ2610/SR TZ2610F/LRTZ2610 SR TZ2610 SR TZ2610F LR TZ2610 G B OWNER’S MANUAL SHORT REACH TRIMMER LONG REACH TRIMMER 848A3393A0 (801) ...
-
Zenoah SRTZ2610F - page 2
GB-2 SRTZ2610/SR TZ2610F/LRTZ2610 EC DECLARATION OF COMFORMITY We, Husqvarna Zenoah Co., Ltd. 1-9, Minamidai, Kawa goe, Saitama, Japan declare in sole responsibility that the follo wing products referred to in this declaration conform with DIRECTIVE 98/37/EC, prEN774 of 5th April 1994. The products referred are : DESIGNA TION : SHOR T REACH TRIMMER ...
-
Zenoah SRTZ2610F - page 3
GB-3 G B SRTZ2610/SR TZ2610F/LRTZ2610 8 9 10 11 12 13 (SRTZ2610) (SRTZ2610F) (LR TZ2610) Information This machine is equipped with an Overload Cancellation Mec hanism. When the cutting blades have got into metal wires or twigs difficult to cut, the mechanism works as a shoc k absorber , and protects the gears and the b lades from se vere reaction w ...
-
Zenoah SRTZ2610F - page 4
GB-4 SRTZ2610/SR TZ2610F/LRTZ2610 Model SRTZ2610F Overall size (LxWxH) mm 1734 x 338 x 254 Dry weight * kg 6.5 Engine T ype Air -cooled 2-stroke gasoline Model Zenoah GZ25N Max output rpm 1.2Hp (0.9kW) at 7500min -1 Idle speed rpm 3000±200min -1 Displacement cm 3 25.4 Fuel Mixture (Gasoline 50 : Oil 1) (when using ZENOAH genuine oil) Carburetor W ...
-
Zenoah SRTZ2610F - page 5
GB-5 G B SRTZ2610/SR TZ2610F/LRTZ2610 1. Read this manual carefully until you completely understand and follow all safety and operating instructions. 2. Keep this manual handy so that you may refer to it later when- ever any questions arise. Also note, if you have any questions which cannot be answered herein, contact the dealer fr om whom you purc ...
-
Zenoah SRTZ2610F - page 6
GB-6 SRTZ2610/SR TZ2610F/LRTZ2610 W ARNING Never place the thr ottle into the high-speed position when starting the engine. 3. After starting the engine, check to make sure that the cutting at- tachment stops moving when the throttle is moved fully back to its original position. If it continues to move even after the throttle has been moved fully b ...
-
Zenoah SRTZ2610F - page 7
GB-7 G B SRTZ2610/SR TZ2610F/LRTZ2610 • IF SOMEONE COMES 1. Guard against hazar dous situa- tions at all times. W arn adults to keep pets and children away fr om the area. Be car eful if you are ap- proached. Injury may result fr om flying debris. 2. If someone calls out or otherwise interrupts you while working, al- ways be sure to turn off the ...
-
Zenoah SRTZ2610F - page 8
GB-8 SRTZ2610/SR TZ2610F/LRTZ2610 MIN SP ACING About 19 inches (48 cm) clamp arrow mark (1) 6. Set up MOUNTING ENGINE 1. Push the shaft tube toward the clutch housing and move it by hand to check that the drive shaft is engaged with the gears. 2. Insert the shaft tube into the clutch housing until it bot- toms, and align the positioning holes on th ...
-
Zenoah SRTZ2610F - page 9
GB-9 G B SRTZ2610/SR TZ2610F/LRTZ2610 7. Fuel ■ RECOMMENDED MIXING RA TIO GASOLINE 50 : OIL 1 (when using ZENO AH genuine oil) • Exhaust emission are controlled b y the funda- mental engine parameters and components (eq., carburation, ignition timing and port timing) with- out addition of an y major hard ware or the intro- duction of an inert m ...
-
Zenoah SRTZ2610F - page 10
GB-10 SRTZ2610/SR TZ2610F/LRTZ2610 8. Operation ST ARTING ENGINE W ARNING The cutting head will start moving upon the engine starts. 1. Rest the unit on a flat, firm place. Keep the cutting head off the gr ound and clear of surr ounding objects as it will start moving upon star ting of the engine. 2. Push the primer several times until overflown fu ...
-
Zenoah SRTZ2610F - page 11
GB-11 G B SRTZ2610/SR TZ2610F/LRTZ2610 8. Operation Idle adjusting screw W ARNING • This product is equipped with extr emely sharp blades, and when used improperly these blades can be ex- tremely danger ous, and improper handling can cause accidents which may in turn lead to serious injur y or death. For this reason, you should always be car eful ...
-
Zenoah SRTZ2610F - page 12
GB-12 SRTZ2610/SR TZ2610F/LRTZ2610 BLADES • When refilling the tank or r esting, it is often a good idea to use the time to oil the cutting blades. • If a gap exists between the upper and lower blades, follow the procedur e below to adjust them so that they fit more closely together . • Loosen lock nut (A) as shown in the diagram. 2. Tighten ...
-
Zenoah SRTZ2610F - page 13
GB-13 G B SRTZ2610/SR TZ2610F/LRTZ2610 9. Maintenance 9. Maintenance W ARNING Make sure that the engine has stopped and is cool before perf orming any service to the machine. Con- tact with moving cutting head or hot m uffler may re- sult in a personal injury . AIR FIL TER • The air filter , if clogged, will reduce the engine perfor - mance. Chec ...
-
Zenoah SRTZ2610F - page 14
GB-14 SRTZ2610/SR TZ2610F/LRTZ2610 9. Maintenance INT AKE AIR COOLING VENT W ARNING •N e ver touc h the cylinder , muffler , or spark plugs with your bare hands immediatel y after stopping the engine. The engine can become very hot when in operation, and doing so could result in se vere b urns. • When chec king the machine to make sure that it ...
-
Zenoah SRTZ2610F - page 15
GB-15 G B SRTZ2610/SR TZ2610F/LRTZ2610 Limited warranty Should any failure occur on the pr oduct under nor mal oper - ating conditions within the applicable warranty period, the failed part will be replaced or repair ed free of charge by a ZENOAH authorized dealer . W ARRANTY PERIOD: 1 year (6 months if used profession- ally , and 30 days if used f ...
Hai una domanda su Zenoah SRTZ2610F?
Utilizza il modulo sottostante
Se non hai risolto il problema con Zenoah SRTZ2610F con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Zenoah SRTZ2610F è probabile che voglia condividere il modo di risolverlo.