Italiano dropdown-ico

Manuale per l’uso CDA FW971

30 pagine Non applicabile
Scarica

Vai alla pagina of 30

Summary
  • CDA FW971 - page 1

    Customer Care Department • The Group Ltd. • Harby R oad • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : customer .care@cda.eu W : www .cda.eu FW971 Integrated Frost Free fridge freezer Manual for Installation, Use and Maintenance ...

  • CDA FW971 - page 2

    2 Important The manufacturer cannot be held responsible for injuries or losses caused by incorrect use or installation of this product. Please note that we reserve the right to invalidate the guarantee supplied with this product following incorrect installation or misuse of the appliance. This appliance is not designed to be used by people (includi ...

  • CDA FW971 - page 3

    3 This appliance has been manufactured to the strictest standards and complies with all applicable legislation, including Electrical safety (L VD) and Electromagnetic interference compatibility (EMC). Parts intended to come into contact with food conform to EEC/89/109 .4 IMPORT ANT INFORMA TION FOR CORRECT DISPOSAL OF THE PRODUCT IN A CCORD ANCE WI ...

  • CDA FW971 - page 4

    4 Important Never store inflammable or explosive items and strong corrosive acids or alkalis in the appliance. This is a household appliance, which is produced in accordance with the national standard. It is intended for food storage only , not for storage of blood, medicine and biological products. T o prevent risk of fire, keep the appliance aw ...

  • CDA FW971 - page 5

    5 Before first use Y ou must allow the fridge to settle for at least twenty four hours prior to switching the power on. It is recommended that you clean the interior of the appliance prior to first use, using a solution of bicarbonate of soda and warm water and then thoroughly drying the interior . The fridge may have an odour to it at first use ...

  • CDA FW971 - page 6

    6 Use Fridge • Never put liquids in the refrigerator uncovered. • Never put hot foods in the refrigerator . W arm food should be allowed to cool to room temperature before being put into the refrigerator . • Nothing should rest against the rear wall of the refrigerator , as this will cause frost and possible condensation problems which will b ...

  • CDA FW971 - page 7

    7 • Store food in small packages (ideally less than 2.5k g). This reduces the freezing time and improves the quality of the food after thawing. • W rap food before putting into the freezer . T o stop the wrapping sticking together , ensure it is dry . • Label the food before freezing with information including type of food and dates of storag ...

  • CDA FW971 - page 8

    8 Storage The fridge section is for short term food storage. Although the temperature can be maintained between 2~8˚C, extended periods of food storage is not recommended. As the cold air circulates within the fridge, the temperature can vary between the dierent sections. As such, foods should be stored in dierent sections according to type. ...

  • CDA FW971 - page 9

    9 The salad crisper is designed with a humidity control to ensure fruit and vegetables last longer . This can be adjusted by the slider at the front right of the salad crisper . Fully opening the slider control to high humidity restricts the amount of dry air entering the crisper from the fridge compartment, extending the life of items such as lett ...

  • CDA FW971 - page 10

    10 Control panel A. Power button T o put the fridge freezer on standby press and hold the power button for appro ximately three seconds. T o start the compressor working again, press and hold the power button for appro ximately three seconds. B. Fridge thermostat dial The fridge temperature is regulated by this dial. The thermostat can be set betwe ...

  • CDA FW971 - page 11

    11 IMPORT ANT Do not use the super cool function for more than 24 hours. C. Freezer thermostat dial The freezer temperature is regulated by this dial. The thermostat can be set between fully anticlockwise (super freeze function) and fully clockwise (least cold). The super freeze function can be used to freeze large quantities of fresh food as quick ...

  • CDA FW971 - page 12

    12 Care and cleaning Always disconnect the appliance from the power supply before any cleaning or maintenance. Both fridge and freezer are frost free and as such this appliance is designed not to require defrosting. The fridge and freezer sections should be cleaned using a solution of bicarbonate of soda and lukewarm water . Do not use abrasive pro ...

  • CDA FW971 - page 13

    13 Defrosting the fridge The fridge is cooled by convection using cold air forced through channels at the rear of the fridge. No defrosting is required. Defrosting the freezer The freezer is frost free and as such is designed not to require defrosting. T o switch o the compressor for a short period of time and so to force a defrost cycle, push a ...

  • CDA FW971 - page 14

    14 T roubleshooting If you have any problems with your appliance, you should check the troubleshooting prior to calling CD A Customer Care to prevent unnecessary service calls and potential cost. If the appliance is not working • Check there is power to the appliance. • The power button on the control panel is switched on. • The house fuses a ...

  • CDA FW971 - page 15

    15 fig. 4 1780 996 40 66 43 625 540 555 1788 min. 30 560-570 550 min = airow min. 30 10 200cm² 200cm² Please note: The LED lighting cannot be replaced without a service call. If the light fails, contact CD A Customer Care. Installation And V entilation This appliance must never be installed close to heat sources, e.g. heating elements, cooker ...

  • CDA FW971 - page 16

    16 V entilation The main consideration when installing any refrigeration unit into a fitted kitchen is ventilation. The heat removed from the cooling compartment needs to be dissipated into the atmosphere. Incorrect ventilation can lead to premature compressor failure, ex cessive power consumption and total system failure. For products intended to ...

  • CDA FW971 - page 17

    17 The open channel at the rear is clearly shown. For the correct operation of the appliance it is important that the top of the housing unit is not blocked o . A channel depth of 40-50mm is normal with most units. A hole is shown in the base shelf of the unit; this allows air to be drawn over the compressor & heat ex change. Some installers ...

  • CDA FW971 - page 18

    18 Fitting the product into the cabinet 1. R emove the gasket protection pieces: The gasket protectors prevent ex cessive seal compression during transport and are required during the installation process. R emove the gasket protector from each door (fig 5) and proceed with the installation. Cover caps are provided to fill the hole; take care whe ...

  • CDA FW971 - page 19

    19 top edge of the product (b). The trim piece should be fitted loosely at this stage to allow access to the top fixing brackets. 4. Fitting the magnetic seal strips: T wo magnetic seals are supplied to fill the gap between the cabinet and the edge of the products. These simply fit against the left and right edges. T o make it easier , it is us ...

  • CDA FW971 - page 20

    20 fig. 13 fig. 12 fig. 11 8. Fitting the bottom cabinet xing bracket: A sliding bracket is provided to secure the non-hinge side of the product to the cabinet. This is fitted to the bottom of the product using two machine screws, as shown below . A guide piece is also provided to ensure the unit is aligned when installed. Fit the bracket an ...

  • CDA FW971 - page 21

    21 pieces from the hinges. 10 . Securing the product to the housing: Secure the product to the housing at the hinge side by using two screws in each hinge. The fixing holes in each hinge as shown in figure 10 . 11. Securing the bottom xing bracket: With the lower guide piece in place slide the lower bracket against the housing unit and tighten ...

  • CDA FW971 - page 22

    22 fig. 14 fig. 15 Fitting the cabinet fascia doors First, fit the upper fascia by following the steps below . After fitting the upper fascia in the correct position, use the lower edge of the upper fascia as a guide for positioning the lower fascia (A distance between the two fascias when installed is normally between 2 and 4mm) and fit the l ...

  • CDA FW971 - page 23

    23 fig. 13 Fitting guides Under end face of fascia to ensure the screws selected will not punch through the fascia door . 4. R emove the fitting guides. 5. Attach the fascia door assembly to the refrigerator (onto the height adjustment screws) and loosely fit the securing nuts. At this stage the final vertical and horizontal position of the fas ...

  • CDA FW971 - page 24

    24 Adjusting the position of the fascia doors The position of the fascia doors can be made in all 3 ax es by following the guide shown below (figure 18). If the range of adjustment detailed below is not enough then the refrigerator is not located correctly in the cabinet and / or the upper fascia fixing plates are incorrectly positioned. Horizont ...

  • CDA FW971 - page 25

    25 Fitting the trims and cover pieces 1. Open the door and lift out the decorative covers (marked ‘a’) in figure 20 2. Remove the position guides (d), turn them round so that the lip at the top faces outwards and insert them into the slots shown in the image (e); these will be used to line up the fascia panels before securing them in position. ...

  • CDA FW971 - page 26

    26 to the fascia panel using the provided wood screws, ensuring that the screws will not penetrate through the fascia where there are any rebates, etc. and then remove the guides. Any small errors, as in the image above, can be adjusted for after the fascia has been mounted. 5. Hang the fascia panel on the support pins and check that the fascia is ...

  • CDA FW971 - page 27

    27 Electrical information W arning! This appliance must be earthed. The mains lead of this appliance has been fitted with a BS 1363A 13 amp fused plug. T o change a fuse in this type of plug, follow the steps below: 1. R emove the fuse cover and fuse. 2. Fit replacement 13A fuse, A ST A approved to BS 1362 type, into the fuse cover . 3. R eplace f ...

  • CDA FW971 - page 28

    28 As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:- • The wire which is coloured GREEN and YELL O W must be connected to the terminal which is marked with letter (E) or by the Earth symbol or coloured GREEN and YELL O W . • ...

  • CDA FW971 - page 29

    29 ...

  • CDA FW971 - page 30

    Please contact our Customer Care Department for Service on the details below Customer Care Department • The Group Ltd. • Harby R oad • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www .cda.eu ...

Fabbricante CDA Categoria Refrigerator

I documenti che otteniamo dal fabbricante del dispositivoCDA FW971 possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici CDA
- manuali per l’uso FW971
- schede prodotto CDA
- opuscoli
- o etichette energetiche CDA FW971
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso CDA FW971.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione CDA FW971, manuali di manutenzione, brevi manuali o manuali utente CDA FW971. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto CDA FW971.

Manuali per l’uso simili

Manuale completo del dispositivo CDA FW971, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare CDA FW971 dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti CDA FW971.

Il manuale per l’uso completo CDA, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale CDA FW971 - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice CDA FW971, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per CDA FW971 che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo CDA FW971 - che ci dovrebbe aiutare nei primi passi durante l'uso CDA FW971
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del CDA FW971
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio CDA FW971 in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su CDA FW971?

Utilizza il modulo sottostante

Se non hai risolto il problema con CDA FW971 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con CDA FW971 è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)