Italiano dropdown-ico

Manuale per l’uso Generac Power Systems 004626-5

64 pagine 4.75 mb
Scarica

Vai alla pagina of 64

Summary
  • Generac Power Systems 004626-5 - page 1

    POWER SYSTEMS, INC. ® ® Owner’ s Man ual Liquid-cooled, Prepac ka ged Standb y Generator s Models: 004373-6 (40 kW/Single-phase w/ 200 Amp T ransfer Switch) 004626-5 (40 kW/Single-phase w/ 200 Amp T ransfer Switch Calif ornia Emissions) ONL Y QUALIFIED ELECTRICIANS OR CONTRACTORS SHOULD A TTEMPT INST ALLA TION!! DEADL Y EXHAUST FUMES. OUTDOOR I ...

  • Generac Power Systems 004626-5 - page 2

    Generac ® Pow er Systems, Inc. I NTRODUCTION Thank you for purchasing the Guardian product line by Generac P ower Systems. This model is a compact, high performance, liquid- cooled, engine - driven gen- erator designed to automatically supply electrical power to operate critical loads during a utility power failure. This unit is factory installed ...

  • Generac Power Systems 004626-5 - page 3

    T able of Contents Guardian Liquid-cooled 40 kW Generator Generac ® Pow er Systems, Inc. 1 Introduction ........................Inside Front Cover Read This Manual Thoroughly ............................IFC Contents ..............................................................IFC Operation and Maintenance ................................IFC How t ...

  • Generac Power Systems 004626-5 - page 4

    2 Generac ® Pow er Systems, Inc. Study these SAFETY RULES carefully before installing, operating or servicing this equipment. Become familiar with this Owner’s Manual and with the unit. The gen- erator can operate safely , efficiently and reliably only if it is properly installed, operated and maintained. Many accidents are caused by failing to ...

  • Generac Power Systems 004626-5 - page 5

    Generac ® Pow er Systems, Inc. 3 • Inspect the generator regularly , and promptly repair or replace all worn, damaged or defective parts using only factory-approved parts. • Before performing any maintenance on the generator , disconnect its battery cables to prevent accidental start -up. Disconnect the cable from the battery post indicated by ...

  • Generac Power Systems 004626-5 - page 6

    4 Generac ® Pow er Systems, Inc. 1.1 U N P ACKING/I NSP ECTION After unpacking, carefully inspect the contents for dam- age. • This standby generator set has been factory installed in an all-weather , metal enclosure that is intended exclusively for outdoor installation. If this generator is used to power electrical load circuits normally power ...

  • Generac Power Systems 004626-5 - page 7

    1.6 MAI N CI RCU IT B R EAKER The generator’s main circuit breaker is included with the unit as shipped from the factory . The breaker for each unit is described as follows: 1.7 ENGI N E P RO TECTIVE DEVICE S The engine has several safety switches that cause it to automatically shut down under the following condi- tions: low oil pressure, high co ...

  • Generac Power Systems 004626-5 - page 8

    6 Generac ® Pow er Systems, Inc. 1.8.2 GEN ERA T OR AN D L O AD COMP A T IBILI TY The generator must be fully compatible with the rated voltage, number of phases and frequency of the con- nected electrical loads. The generator , connected elec- trical devices, or both, can be damaged if voltage, num- ber of phases and frequency are not compatible. ...

  • Generac Power Systems 004626-5 - page 9

    1.1 0 ENGI N E OI L REC OMM EN D A TIONS The unit has been filled with 15W -40 engine oil at the factory . Use a high- quality detergent oil classified “F or Service CC, SD , SE or SF .” Detergent oils keep the engine cleaner and reduce carbon deposits. Use oil hav- ing the following SAE viscosity rating, based on the ambient temperature range ...

  • Generac Power Systems 004626-5 - page 10

    8 Generac ® Pow er Systems, Inc. If an open bottom is used, the engine-generator is to be installed over non-combustible materials and should be located such that combustible materials are not capable of accumulating under the generator set. Only qualified, competent installation contractors or electricians thoroughly familiar with applicable code ...

  • Generac Power Systems 004626-5 - page 11

    Generac ® Pow er Systems, Inc. 9 Figure 2.1 – Basic Standby Electric System 2.2 EM ERGENCY CI RCU IT IS OL A TION M E THOD This method prevents overloading the generator by keeping electrical loads below the wattage/amperage capacity of the generator . If the generator is powering only critical loads, within its wattage/amperage capacity , durin ...

  • Generac Power Systems 004626-5 - page 12

    10 Generac ® Pow er Systems, Inc. 2.7 B A TTER Y I NS T ALLA TION Standby generators installed with automatic trans- fer switches will crank and start automatically when NORMAL (UTILITY) source voltage is removed or is below an acceptable pr eset level. T o prevent such automatic start-up and possible injury to personnel, do not connect battery ca ...

  • Generac Power Systems 004626-5 - page 13

    2.8 P R EP AR A TION B EFOR E S T ART -U P The instructions in this section assume that the standby generator has been properly installed, serviced, tested, adjusted and otherwise prepared for use by a competent, qualified installation contractor . Be sure to read the “Safety Rules” on P ages 2 and 3, as well as all other safe- ty information i ...

  • Generac Power Systems 004626-5 - page 14

    12 Generac ® Pow er Systems, Inc. 3.1 C ONTROL CONS OLE C OMPON ENTS The components of a liquid- cooled generator control console (Figure 3.1) are as follows: Figure 3.1 – Control Console 3.1.1 AC V OL TM ETER The voltmeter displays generator AC output voltage dur- ing operation. V oltage is regulated by a solid- state volt- age regulator and is ...

  • Generac Power Systems 004626-5 - page 15

    3.2.2 “OF F” POSITION This switch position shuts down the engine. This posi- tion also prevents operation. 3.2.3 “MAN U AL ” POSITION Set the switch to MANU AL to crank and start the engine. Transfer to standby power will not automatically occur unless there is a utility failure. With the switch set to AUTO, the engine may crank and start a ...

  • Generac Power Systems 004626-5 - page 16

    Figure 3.2 – Engine Block Heater Refer to applicable wiring diagram(s) and electrical schematic(s) at the back of this manual for wiring con- nections. 3.6 WEEKL Y EXERCISE CY CLE The generator will start and exercise once every seven days. During this weekly exercise, the unit runs for approximately 20 minutes and shuts down. Transfer of loads t ...

  • Generac Power Systems 004626-5 - page 17

    4.2 CHANGI NG TH E ENGI N E OI L AN D FIL T E R 4.2.1 ENGI NE OI L R EC OMM EN D A TIONS Use oil of API Service Class SG, SH or SJ . The recommended oil grade for the engine is SAE 15W -40. NOTE: The unit is supplied with “break-in ” oil. See the “Service Schedule,” Section 4.12, for the first required oil change. Any attempt to crank or st ...

  • Generac Power Systems 004626-5 - page 18

    16 Generac ® Pow er Systems, Inc. 4 . 4 S P A RK PL UG S Reset the spark plug gap or replace the spark plugs as necessary . See Section 4.12. 1. Clean the area around the base of the spark plugs to keep dirt and debris out of the engine. Clean the plugs by scraping using a wire brush. Do not “blast” the spark plugs to clean. 2. Remove the spar ...

  • Generac Power Systems 004626-5 - page 19

    Generac ® Pow er Systems, Inc. 17 4.7 O VER L O AD P RO TECTION FOR ENGI N E DC ELE CTR ICAL SY S TEM Engine cranking, start -up and running are controlled by a solid- state engine controller circuit board. Battery voltage is delivered to that circuit board via a 15-amp fuse. These overcurrent protection devices will open if the circuit is overloa ...

  • Generac Power Systems 004626-5 - page 20

    18 Generac ® Pow er Systems, Inc. 4.1 1 OUT OF SERVICE P ROCEDU R E 4.1 1.1 R EMO V AL F ROM SERVICE If the generator cannot exercise every seven days, and it is to be out of service longer than 90 days, prepare the generator for storage as follows: 1. Start the engine and let it warm up. 2. Close the fuel shutoff valve in the fuel supply line and ...

  • Generac Power Systems 004626-5 - page 21

    Generac ® Pow er Systems, Inc. 19 Section 4 — Maintenance Guardian Liquid-cooled 40 kW Generator 4.1 2 SERVICE S CH EDU LE A TTENTION: It is recommended that all service work be performed by the nearest Generac/Guar dian Authorized Dealer . SYSTEM/COMPONENT PROCEDURE FREQUENCY X = Action Inspect Change Clean W = W eekly R = Replace/Adjust as Nee ...

  • Generac Power Systems 004626-5 - page 22

    20 Generac ® Pow er Systems, Inc. Section 5 — T roubleshooting Guardian Liquid-cooled 40 kW Generator 5.1 TROU B LE SHOO TI NG GU I DE P ROB LEM CAUSE C OR R E CTION The engine will not crank. 1. F use blown 1. Replace fuse. 2. Loose, corroded or defective 2. Tighten, clean or replace battery cables as necessary . 3. Defective starter contactor ...

  • Generac Power Systems 004626-5 - page 23

    Generac ® Pow er Systems, Inc. 21 Section 6 — Installation Diagram Guardian Liquid-cooled 40 kW Generator Drawing No. 0E7 0 1 5 ...

  • Generac Power Systems 004626-5 - page 24

    S 1 6 S 1 5 0 0 0 2 1 9 150 2 2 9 14 13 79 14 15 15 15 68 4 56 85 69 86 T S1 HZ - FRE Q UENCY METE R HZ TB1 - TERMINAL BL OC K S LE G EN D GCB GC B - GO VERN O R CO NTR O L B O AR D BL UE BL UE RED BLA CK P / N 986 4 7 22 Generac ® Pow er Systems, Inc. Section 7 — Electrical Data (Model No. 0043 7 33, 0043 73 4 & 0043 7 35) Guardian Liquid-c ...

  • Generac Power Systems 004626-5 - page 25

    Generac ® Pow er Systems, Inc. 23 AC TUAT O R B R O WN O RAN G E Y ELL O W B LA C K N . C . TO GO VERN O R HM C P EH T S1 , TS2 - TERMINAL STRIPS L P C - L O WER PANEL CO NNE C TI O N TS 2 R 1 - RESISTOR , FIELD BOOST V M - METER , AC OUTPUT VOLTAGE A VR - A U T O MATI C V O LTA G E RE GU LAT O R S W2 - S WIT C H- S ET EXER C I S E S W1 - S WIT C ...

  • Generac Power Systems 004626-5 - page 26

    A AM VM L1 15 12 3 5 6 2 4 1 B A 17 1 13 2 16 5 7 D 14 11 9 C AP E 3 4 TO L O WER PANEL ( CO NNE C T O R C P) U J B T S W V H X O G A N Q M E K F C D 4 5 10 12 3 TO EN G INE ( CO NNE C T O R EH) 6 11 12 11 7 + 2 19 15 3 18 16 14 - + - + - CO NTA C T S 2 - 3 2 - 7 1 2 - 3 12 - 7 15 - 14 15 - 1 8 19 - 14 6 7 P HA S E S ELE C T O R S WIT C H 0 6 4 65 ...

  • Generac Power Systems 004626-5 - page 27

    Generac ® Pow er Systems, Inc. 25 S 1 5 N 00 P 1 7 8 K M S 1 23 N2 N1 T1 S R T2 X 19 4 G F B E 6 S 1 6 2 1 5 7 58 S3 N1 N2 T2 23 19 4 CUS T O MER CO NNE C TI O N CUS T O MER CO NNE C TI O N 1 2 0/ 24 0 V. 1-PHA S E E 1 T O E 3 24 0 V. E3 T O 00 E 1 T O 00 1 2 0 V. B R US H U NIT S 4 4 33 22 E1 C B2 E3 C T1 0 11 S 1 5 0 H S 1 6 G A N 5 7 58 C T2 O ...

  • Generac Power Systems 004626-5 - page 28

    N . C . EH HM C P 85 56 B LA C K AVR 14 13 14 85 56 85 0 4 6 5 N2 N1 14 13 1 4 14 13 85 0 85 56 RED P F C 14 85 85 6 4 4 B LA C K TR1 B L U E B LA C K B L U E RED B L U E 239 T2 T1 2 25 A 0 1 5 C T2 T1 1 7 8 1 5 E 14 8 5 1 7 6 L1 - S 1 6 2 2 9 S 1 5 15 T2 15 E 2 2 5 A T1 B L U E 15 S W2 15 S 1 6 14 65 S 1 5 65 S 1 6 S 1 5 6 7 15C B LA C K TS 2 N2 4 ...

  • Generac Power Systems 004626-5 - page 29

    Generac ® Pow er Systems, Inc. 27 B J X W S T V U A O N M Q F K G H E C D 5 4 3 6 C AP L1 8 9 1 2 10 11 12 7 P SW - SWITCH , PHASE SELECTOR S W2 - SWITCH , SET EXERCISE S W1 - SWITCH , AUTO/OFF/MANUAL T R1 - TRANSFORMER , UTILITY SENSING 24VA R 1 - RESISTOR , FIELD BOOST V M - METER , AC OUTPUT VOLTAGE L 1 - LIGHT , FAULT INDICATOR C AP - C APA C ...

  • Generac Power Systems 004626-5 - page 30

    ( - ) ( + ) (+) 1 2 3 1 2 E C1 OS * * F S WHITE EH G REE N BLA CK LE G END : O NLY US ED O N EMI SS I O N S M O DEL S 12 1 3 11 1 0 8 9 5 7 6 2 4 3 1 BAT 1 3 ALT 1 3 BLA CK G N D 0 1 3 * SM 1 6 RED RED 1 6 BAT: E C 1 : CC: EH: F S: G ND : I C: ID: S M : MP1: WL S: * A C T : ALT: * 1 60 85 85 56 14 1 3 14 7 9 0 0 0 1 61 GND 56 CC 0 85 85 85 ENGINE C ...

  • Generac Power Systems 004626-5 - page 31

    Generac ® Pow er Systems, Inc. 29 T C AL T ID ( + ) ( - ) 14 A CT * 0 12V BATTER Y 0 H CT 85 WL S 0 1 60 1 61 CC MP1 85 * L OS F S 1 61 1 60 56 7 9/C LEA R 0/ BAR E 0/ BLA CK 0 85 0 85 0 14 7 9 1 3 14 1 2 3 8 6 4 5 7 E C1 1 0 9 12 11 O NLY US ED O N EMI SS I O N S M O DEL S S TARTER CO NTA C T OR MA G NETI C PI C K U P 1 I G NITI O N DI S TRIB U T ...

  • Generac Power Systems 004626-5 - page 32

    30 Generac ® Pow er Systems, Inc. Section 8 — Exploded Views and P arts Lists Guardian Liquid-cooled 40 kW Generators Mounting Base - Drawing No. 0E69 7 6-A 2 0 1 8 15 2 6 24 1 38 37 36 35 2 5 30 31 3 2 5 12 34 1 6 3 17 33 32 25 39 9 BLA CK 2 9 38 RED 5 1 9 16 1 17 1 3 12 11 1 0 SO LEN O I D T O S TARTE R 7 2 2 8 27 O n O il Pan . To O il Drai n ...

  • Generac Power Systems 004626-5 - page 33

    Generac ® Pow er Systems, Inc. 31 ITEM P ART NO . QTY . DESCRIPTION 10 E 6 9 00 1 MTG BASE 4.3L D/D PRE-P ACK 2 038804T 1 CABLE BA TT RED #1 X 31.00 3 055414 1 LUG SLDLSS #2-#8 X 17/64 CU 4 0A4084 REF . MOUNT ENGINE (R&L) 5 02212 9 2 W ASHER LOCK M8-5/16 6 045771 2 NUT HEX M8-1.25 G8 YEL CHR 7 022237 7 W ASHER LOCK 3/8 80 2 9 745 6 SCREW HHC 3 ...

  • Generac Power Systems 004626-5 - page 34

    32 Generac ® Pow er Systems, Inc. 26 30 25 3 6 22 3 1 3 1 24 19 5 3 ( ONE PER SIDE ) 2 11 29 2 B A S E FRAME 29 27 6 10 5 8 1 39 29 23 15 33 3 4 3 2 9 28 11 2 12 12 11 5 29 13 10 27 11 29 17 7 42 21 16 Section 8 — Exploded Views and P arts Lists Guardian Liquid-cooled 40 kW Generators Compartment - Drawing No. 0D8992-A ...

  • Generac Power Systems 004626-5 - page 35

    Generac ® Pow er Systems, Inc. 33 ITEM P ART NO . QTY . DESCRIPTION 1 0C35 9 4 10 ASSEMBL Y M6 HINGE 2 0E3257 4 SCREW TH-FRM M6 W/CAP SHKPRF W 3 0A335 9 40 SCREW BHSC M6-1.0 X 16 SS 4 * 02276 9 5 W ASHER SHAKEPR OOF INT #10 5 0C2522 (A) 5 DOOR SMALL STD . WELD 6 0C2527 (A) 1 CORNER POST LH REAR 7 0C2528 (A) 1 CORNER POST RH REAR 8 0C2535 (A) 1 COR ...

  • Generac Power Systems 004626-5 - page 36

    34 Generac ® Pow er Systems, Inc. 53 1 2 14 VIEW A - A 17 18 16 2 0 19 5 1 5 2 39 3 18 15 13 5 2 53 59 35 5 6 5 4 55 56 5 7 4 1 18 49 50 21 6 4 36 26 3 7 60 A A 9 5 1 5 2 53 60 23 43 29 42 6 1 6 1 24 28 25 41 27 50 49 45 46 3 I N S IDE. 3 0 1 P ANEL FA C E 58 63 58 18 49 50 6 2 22 + + - E VERY 7 DAYS , AT TIME SET. 30 S E T 8 1 988 M I E V 33 3 1 ...

  • Generac Power Systems 004626-5 - page 37

    Generac ® Pow er Systems, Inc. 35 ITEM P ART NO . QTY . DESCRIPTION 1 0D5488 1 P ANEL BTM & BACK CONTR OL P ANEL 2 0D1521A 1 CONTR OL P ANEL, FRONT W/ SILK SCREEN 3 0D1522 2 P ANEL,SIDE CO VER CONTROL P ANEL 4 067680 1 ASSY VOL T AGE REGULA T OR 60HZ 5 0C8243 1 W ASHER LOCK HDPDEUTSCH 6 0C8244 1 NUT , HDP DEUTSCH 8 048467 1 CIRCT BRK 7 X 1 ET ...

  • Generac Power Systems 004626-5 - page 38

    36 Generac ® Pow er Systems, Inc. Section 8 — Exploded Views and P arts Lists (Model No. 0046262, 00462 63 & 0046264) Guardian Liquid-cooled 40 kW Generator Control Panel – Drawing No. 0D69 7 8-C ...

  • Generac Power Systems 004626-5 - page 39

    Generac ® Pow er Systems, Inc. 37 ITEM P ART NO . QTY . DESCRIPTION 1 0D73 9 7 1 PNL BTM & BA CK CNTL PNL 04626 2 0D1521A 1 CONTROL P ANEL FRONT W/ SILK SCREEN 3 0D1522 1 P ANEL SIDE CO VER CONTROL P ANEL 4 067680 1 ASSY V OL T AGE REGULA T OR 60HZ 5 0C8243 1 W ASHER LOCK HDP DEUTSCH 6 0C8244 1 NUT , HDP DEUTSCH 7 0A6321 1 P ANEL LEFT SIDE E 8 ...

  • Generac Power Systems 004626-5 - page 40

    38 Generac ® Pow er Systems, Inc. Section 8 — Exploded Views and P arts Lists Guardian Liquid-cooled 40 kW Generators Connection Box – Drawing No. 0E6892-A ...

  • Generac Power Systems 004626-5 - page 41

    Generac ® Pow er Systems, Inc. 39 Section 8 — Exploded Views and P arts Lists Guardian Liquid-cooled 40 kW Generators Connection Box – Drawing No. 0E6892-A ITEM P ART NO . QTY . DESCRIPTION 1 0E6353 1 LO WER P ANEL 15 2 0D548 9 1 CO VER LO WER CONNECTION BO X 3 0E6427 1 PLA TE GLAND 4 023484N 2 BUSHING SNAP SB-2.5-31 5 0E6454 1 BRA CKET NEUTRA ...

  • Generac Power Systems 004626-5 - page 42

    40 Generac ® Pow er Systems, Inc. 1 5 21 SC R O LL DETAI L T HREAD IN SENSOR ( 6 ) UNTIL CONTACT I S MADE WITH RING GEAR , THEN BACK OFF 1/ 2 T O 3/ 4 T U RN AND TI G HTEN N U T. DO N O T R O TATE EN G INE D U RIN G THI S AD JUS TMENT. 18 2 C A U TI O N: NO TE: F lLYWHEEL AD JUS TMENT TO EN G INE 35 9 6 8 4 1 35 28 29 25 2 TO EN G INE FLYWHEEL 15 ...

  • Generac Power Systems 004626-5 - page 43

    Generac ® Pow er Systems, Inc. 41 Section 8 — Exploded Views and P arts Lists Guardian Liquid-cooled 40 kW Generators Generator – Drawing No. 0E689 1 ITEM P ART NO . QTY . DESCRIPTION 1 051768 7 SCREW HHC M12-1.75 X 25 G8.8 2 05176 9 7 W ASHER LOCK M12 3 0A8240 2 FLEX PLA TE SAE10 40 3 9 253 6 SCREW HHC M8-1.25 X 20 G8.8 5 02212 9 7 W ASHER LO ...

  • Generac Power Systems 004626-5 - page 44

    42 Generac ® Pow er Systems, Inc. Section 8 — Exploded Views and P arts Lists Guardian Liquid-cooled 40 kW Generators Engine – Drawing No. 0D6980-D ...

  • Generac Power Systems 004626-5 - page 45

    Generac ® Pow er Systems, Inc. 43 ITEM P ART NO . QTY . DESCRIPTION 10 A 9 046 1 ENGINE 4.3L GM 20 A 9 118A 1 FL YWHL 4.3L GM SAE 3 070022 1 W ASHER ST AR M12 EXT 4 0A6021 6 SCREW HHC 7/16-20 X 1 G8 60 5 9 056A 1 ST ARTER 5.7L/7.4L GM 80 A 9 050 2 BOL T ST ARTER 4.3L 9 022237 17 W ASHER LOCK 3/8 10 045772 1 NUT HEX M10-1.5 G8 YEL CHR 11 04 9 226 1 ...

  • Generac Power Systems 004626-5 - page 46

    44 Generac ® Pow er Systems, Inc. 40 3 2 48 23 40 24 45 3 1 6 22 3 4 3 7 40 43 20 39 44 10 11 36 34 3 14 27 2 2 18 50 30 41 3 1 33 5 13 4 19 25 43 21 3 4 26 35 40 46 8 7 47 9 12 1 3 8 26 34 16 17 15 Section 8 — Exploded Views and P arts Lists Guardian Liquid-cooled 40 kW Generators Engine – Drawing No. 0A4304-N ...

  • Generac Power Systems 004626-5 - page 47

    Generac ® Pow er Systems, Inc. 45 ITEM P ART NO . QTY . DESCRIPTION 10 A 9 046 1 ENGINE 4.3L GM 2 0A4084 2 MOUNT ENGINE (R & L) 3 0A423 9 1 PULLEY CRANKSHAFT 4 0A4240 1 PULLEY W A TER PUMP 5 0A5640 1 SP ACER F AN 50MM 4.3L (35KW UNITS ONL Y) 0A5640A 1 SP ACER F AN 62MM (45KW UNITS ONL Y) 6 0A563 9 1 F AN 17" REVRS RO T (35KW UNITS ONL Y) ...

  • Generac Power Systems 004626-5 - page 48

    17 K IT PART N O . 0 D7 9 47 20 18 19 K IT PART N O . 0 D7 9 4 8 30 3 1 33 35 3 4 3 2 37 9 10 2 11 14 16 39 38 36 12 27 40 29 1 10 16 6 5 27 "A " 2 2 15 7 24 22 23 TO "A" K IT PART N O . 0 D 8 121 10 21 17 46 Generac ® Pow er Systems, Inc. Section 8 — Exploded Views and P arts Lists Guardian Liquid-cooled 40 kW Generators 4.3 ...

  • Generac Power Systems 004626-5 - page 49

    Generac ® Pow er Systems, Inc. 47 ITEM P ART NO . QTY . DESCRIPTION 1 0D7825A 1 RADIA T OR COPPER BRASS 2 0D8251 1 F AN GU ARD BO TT OM 3 0D8252 1 F AN GU ARD T OP 4 024655 4 SCREW HHTT 1/4-20 X 1 CZ 5 0220 9 7 4 W ASHER LOCK M6-1/4 6 022473 4 W ASHER FLA T 1/4 ZINC 7 0D7174 1 VENTURI 4.3L 22" F AN 0D7174A 1 VENTURI 4.3L 17" F AN 9 0D787 ...

  • Generac Power Systems 004626-5 - page 50

    ITEM P ART NO . QTY . DESCRIPTION 10 5 99 02A 1 CAP RAIN 2.50 / 2.6 9 20 C 9 641 1 TUBE STRAIGHT 'A' GROUP 30 C 9 650 1 MUFFLER 2-1/2" INLET/OUTLET 4 0C4114A 2 CLAMP BAND MUFFLER 6.5" 5 0C4126 2 BRA CKET MUFFLER MOUNTING 6 0D5787 1 TUBE ELBO W 9 0 DEG 2.5" 7 0A5215B 2 PIPE FLEX 2.5" 80 E 0 6 99 1 TUBE, CROSS O VER 9 0E ...

  • Generac Power Systems 004626-5 - page 51

    Generac ® Pow er Systems, Inc. 49 ITEM P ART NO . QTY . DESCRIPTION 1 037561 1 NUT WING 1/4-20 NYLK 2 0A4632A 1 PLA TE AIR CLEANER T OP 3 0A4637 1 FIL TER AIR 11.5" CA326 4 0A4632B 1 PLA TE,AIR CLEANR BO T 5 062522 1 STUD TH 1/4-20 X 3 G2 ZNC FULL 6 022127 1 NUT HEX 1/4-20 STEEL 7 0577 9 6 1 GROMMET 8 0577 9 5A 1 BARBED EL 9 0 3/4 PLASTIC 2 5 ...

  • Generac Power Systems 004626-5 - page 52

    Section 8 — Exploded Views and P arts Lists (Model No. 0043 7 33, 0043 73 4 & 0043 7 35) Guardian Liquid-cooled 40 kW Generators 4.3L Nat. Gas Fuel Syst em – Drawing No. 0E7 011- B 25 CO VER VALVE 12 33 M ANIF O LD TO INTAKE 36 3 4 28 29 30 35 38 TO 22 40 2 39 24 17 41 15 16 27 24 21 3 7 20 2 TO S TEPPER MO T O R 6 5 1 4 18 12 10 1 9 8 3 19 ...

  • Generac Power Systems 004626-5 - page 53

    Generac ® Pow er Systems, Inc. 51 ITEM P ART NO . QTY . DESCRIPTION 1 065 9 07 1 SUPPOR T SOLENOID NA T GAS 2 026812 3 ELBO W 9 0D 3/4 NPT 3 028238 2 BOL T U 5/16-18 X 1.50 4 0C75 9 8 1 ASSY NA TURAL GAS SOLENOID 5 0264 9 0 2 NIPPLE PIPE 3/4 NPT X 2 6 026577 2 BUSHING REDUCER 1 T O 3/4 7 055 9 44 1 REGULA T OR NA T GAS LPG V APOR 8 028237 2 SADDLE ...

  • Generac Power Systems 004626-5 - page 54

    52 Generac ® Pow er Systems, Inc. 24 TO INTAK E M ANIF O LD 38 43 39 22 12 33 3 1 30 41 4 36 3 4 40 35 29 28 3 7 CO VER VALVE TO 21 P/ N 0 D 3509 ASS EMBLY F AN SC R O L L A TTA C H T O 33 12 2 44 25 17 20 2 24 1 4 5 18 10 6 11 12 3 7 19 2 8 9 6 5 18 17 11 12 27 15 16 14 23 13 Section 8 — Exploded Views and P arts Lists (Model No. 0046262, 00462 ...

  • Generac Power Systems 004626-5 - page 55

    Generac ® Pow er Systems, Inc. 53 ITEM P ART NO . QTY . DESCRIPTION 1 065 9 07 1 SUPPOR T SOLENOID NA T GAS 2 026812 3 ELBO W 9 0D 3/4NPT 3 02225 9 4 NUT HEX 5/16-18 STEEL 4 0C75 9 8 1 ASSY NA TURAL GAS SOLENOID 5 0264 9 0 2 NIPPLE PIPE 3/4 NPT X 2 6 026577 2 BUSHING REDUCER 1 T O 3/4 7 0D2758 1 REGULA T OR N/G (R600S) 8 0E0521 1 SUPPOR T REGULA T ...

  • Generac Power Systems 004626-5 - page 56

    54 Generac ® Pow er Systems, Inc. Section 8 — Exploded Views and P arts Lists (Model No. 0046262, 00462 63 & 0046264) Guardian Liquid-cooled 40 kW Generators Exhaust – Drawing No. 0E1 34 7-A ...

  • Generac Power Systems 004626-5 - page 57

    Generac ® Pow er Systems, Inc. 55 ITEM P ART NO . QTY . DESCRIPTION 10 5 99 02A 1 CAP RAIN 2.50 / 2.6 9 20 C 9 641 1 TUBE STRAIGHT 'A' GROUP 3 0D4208 1 MUFFLER CA T AL YST 4.3L 4 0D5061 4 MOUNTING BAND A-GRP CA T AL YST 5 0C4126 2 BRA CKET MUFFLER MOUNTING 6 0D5787 1 TUBE ELBO W 9 0 DEG 2.5" 7 0A5215B 2 PIPE FLEX 2.5" 8 0E06 99 ...

  • Generac Power Systems 004626-5 - page 58

    56 Generac ® Pow er Systems, Inc. Section 8 — Exploded Views and P arts Lists (Model No. 0043 7 33, 0043 73 4 & 0043 7 35) Guardian Liquid-cooled 40 kW Generators Electronic Governor – Drawing No. 0A26 15-F ITEM P ART NO . QTY . DESCRIPTION 10 9 82 9 0 1 ASSEMBL Y MO T OR STEPPER 2 0A343 9 1 BRA CKET GO VERNOR MOUNTING 30 9 8 9 58A 1 CONNE ...

  • Generac Power Systems 004626-5 - page 59

    Generac ® Pow er Systems, Inc. 57 ITEM P ART NO . QTY . DESCRIPTION 1 0C4 9 05 1 BARBED EL 45 FITTING 2 057822 2 CLAMP HOSE #8 .53-1.00 3 077043E 1 CONDUIT FLEX 1" BLA CK (15"LG) 4 050 9 67 1 HOSE 5/8 ID RIA 250F (46"LG) 5 0A6283 1 HOSE PREFORMED BLOCK HEA TER 6 057822 2 CLAMP HOSE #8 .53-1.00 7 0C4 9 05 1 BARBED EL 45 3/8NPT X 5/8O ...

  • Generac Power Systems 004626-5 - page 60

    58 Generac ® Pow er Systems, Inc. Section 9 – Notes Guardian Liquid-cooled 40 kW Generators ...

  • Generac Power Systems 004626-5 - page 61

    Generac ® Pow er Systems, Inc. 59 Section 9 – Notes Guardian Liquid-cooled 40 kW Generators ...

  • Generac Power Systems 004626-5 - page 62

    60 Generac ® Pow er Systems, Inc. Section 1 0 – W arranty Guardian Liquid-cooled 40 kW Generators CALI FOR N IA EM ISSION C ONTROL W AR R ANT Y S T A TEM ENT Y OU R W ARR ANT Y RIGHTS AND OB LIGA TIONS The California Air Resources Board (CARB) and Generac P ower Systems, Inc. (Generac) are pleased to explain the Emission Control System W arranty ...

  • Generac Power Systems 004626-5 - page 63

    Generac ® Pow er Systems, Inc. 61 Section 1 0 – W arranty Guardian Liquid-cooled 40 kW Generators EM IS SION CONTROL S Y STEM W AR R ANTY Emission Control System W arranty (ECS W arranty) for 1995 and later model year engines: (a) Applicability: This warranty shall apply to 1995 and later model year engines. The ECS W arranty Period shall begin ...

  • Generac Power Systems 004626-5 - page 64

    Part No. 0E7018 Revision D (06/02/05) Printed in U.S.A. Section 1 0 – W arranty Guardian Liquid-cooled 40 kW Generators GENERA C PO WER SYSTEMS "TWO YEAR" LIMITED W ARRANTY FOR GU ARDIAN ® "PREP A CKA GED EMERGENCY A UT OMA TIC ST ANDBY GENERA T ORS" F or a period of two years from the date of original sale, Generac P ower Sy ...

Fabbricante Generac Power Systems Categoria Portable Generator

I documenti che otteniamo dal fabbricante del dispositivoGenerac Power Systems 004626-5 possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Generac Power Systems
- manuali per l’uso 004626-5
- schede prodotto Generac Power Systems
- opuscoli
- o etichette energetiche Generac Power Systems 004626-5
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Generac Power Systems 004626-5.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Generac Power Systems 004626-5, manuali di manutenzione, brevi manuali o manuali utente Generac Power Systems 004626-5. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Generac Power Systems 004626-5.

Manuali per l’uso simili

Manuale completo del dispositivo Generac Power Systems 004626-5, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Generac Power Systems 004626-5 dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Generac Power Systems 004626-5.

Il manuale per l’uso completo Generac Power Systems, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Generac Power Systems 004626-5 - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Generac Power Systems 004626-5, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Generac Power Systems 004626-5 che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Generac Power Systems 004626-5 - che ci dovrebbe aiutare nei primi passi durante l'uso Generac Power Systems 004626-5
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Generac Power Systems 004626-5
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Generac Power Systems 004626-5 in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Generac Power Systems 004626-5?

Utilizza il modulo sottostante

Se non hai risolto il problema con Generac Power Systems 004626-5 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Generac Power Systems 004626-5 è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)