Italiano dropdown-ico

Manuale per l’uso NEC MultiSync EA294WMi

30 pagine Non applicabile
Scarica

Vai alla pagina of 30

Summary
  • NEC MultiSync EA294WMi - page 1

    MultiSync EA294WMi User ’ s Manual ...

  • NEC MultiSync EA294WMi - page 2

    Inde x W arning, Caution ..........................................................................................................................English-1 Registration Information ...............................................................................................................English-2 Recommended use ............................... ...

  • NEC MultiSync EA294WMi - page 3

    English-1 English W ARNING CA UTION CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED FROM W ALL SOCKET . T O FULL Y DISENGAGE THE POWER T O THE UNIT , PLEASE DISCONNECT THE POWER CORD FROM THE AC OUTLET .DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE P ARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. ...

  • NEC MultiSync EA294WMi - page 4

    English-2 Registration Inf ormation FCC Inf ormation 1. Use the attached specifi ed cables with the MultiSync EA294WMi (L292VK) monitor so as not to interfere with radio and television reception. (1) The power supply cord you use must have been approved by and comply with the safety standards of U.S.A., and meet the following condition. Power supp ...

  • NEC MultiSync EA294WMi - page 5

    English-3 English Recommended use Safety Precautions and Maintenance FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE FOLLOWING WHEN SETTING UP AND USING THE LCD COLOR MONIT OR: • DO NO T OPEN THE MONIT OR. There are no user serviceable parts inside and opening or removing covers may expose you to dangerous shock hazards or other risks. Refer all servici ...

  • NEC MultiSync EA294WMi - page 6

    English-4 CORRECT PLACEMENT AND ADJUSTMENT OF THE MONITOR CAN REDUCE EYE, SHOULDER AND NECK F A TIGUE. CHECK THE FOLLOWING WHEN YOU POSITION THE MONITOR: • For optimum performance, allow 20 minutes for the display to warm up. • Adjust the monitor height so that the top of the screen is at or slightly below eye level. Y our eyes should look slig ...

  • NEC MultiSync EA294WMi - page 7

    English-5 English Contents Y our new NEC monitor box* should contain the following: • MultiSync monitor with a tilt/swivel/pivot/height adjust stand • Power Cord* 1 • Video Signal Cable (DisplayPort cable) • Video Signal Cable (DVI-D to DVI-D cable)* 2, * 3 • USB Cable • ControlSync Cable (ø 2.5 stereo micro plug) • Setup Manual • ...

  • NEC MultiSync EA294WMi - page 8

    English-6 Figure 1 Control keys Figure 2 Screws Quic k Star t T o attach the Base to the LCD stand: 1. Place monitor face down on a non-abrasive surface ( Figure 1 ). NO TE: Handle with care when monitor facing down, for avoiding damage to the front control keys. 2. Please rotate the stand 90 degrees as shown in Figure 1 . NO TE: Handle with care w ...

  • NEC MultiSync EA294WMi - page 9

    English-7 English 3. Place hands on each side of the monitor to tilt the LCD panel 30-degree angle and lift up to the highest position. 4. Connect all cables to the appropriate connectors ( Figure C.1 ). When using the USB cable, connect the B type connector to the USB upstream port on the right back side of the monitor and the A type connector to ...

  • NEC MultiSync EA294WMi - page 10

    English-8 8. T urn on the computer , then turn on the monitor by pressing the power sign on the front bezel ( Figure E.1 ). 9. No T ouch Auto Adjust automatically adjusts the monitor to optimal settings upon initial setup. For further adjustments, use the following OSD controls: • AUTO CONTRAST (Analog input only) • AUTO ADJUST (Analog input on ...

  • NEC MultiSync EA294WMi - page 11

    English-9 English Figure S.1 Tilt and Swivel Grasp the top and bottom sides of the monitor screen with your hands and adjust the tilt and swivel as desired ( Figure TS.1 ). Figure TS.1 NO TE: Handle with care when tilting the monitor screen. Flexib le Arm Installation This LCD monitor is designed for use with a fl exible arm. T o prepare the monit ...

  • NEC MultiSync EA294WMi - page 12

    English-10 Mount Flexib le Arm This LCD monitor is designed for use with a fl exible arm. 1. Follow the instructions on how Remove Monitor Stand for Mounting to remove the stand. 2. Use the 4 screws removed from the stand to attach the arm to the monitor ( Figure F .1 ). Caution: Use ONL Y the screws (4 pcs) that were removed from the stand to avo ...

  • NEC MultiSync EA294WMi - page 13

    English-11 English Contr ols OSD (On-Screen Displa y) control ke ys on the front of the monitor function are as f ollows: T o access OSD menu, touch any of the control keys. T o change signal input, touch the SELECT key . NO TE: Exit OSD in order to change signal input. 1 Ambibright Sensor Human Sensor Detects the level of ambient lighting, allowin ...

  • NEC MultiSync EA294WMi - page 14

    English-12 ECO T OOLS BRIGHTNESS Adjusts the overall image and background screen brightness. If ECO MODE is set to 1 or 2, a bar for CARBON FOOTPRINT will appear . CONTRAST Adjusts the overall image and background screen brightness by input signal level. ECO MODE Decreases the amount of power consumption by reducing the brightness level. OFF: No fu ...

  • NEC MultiSync EA294WMi - page 15

    English-13 English HUMAN SENSING The human sensor on the front side of the monitor detects the movement of a person by using the HUMAN SENSING function. The HUMAN SENSING has three settings: OFF: No HUMAN SENSING. 1 (LIGHT): After it is detected that there is no person after a period of time, the monitor shifts to low brightness mode automatically ...

  • NEC MultiSync EA294WMi - page 16

    English-14 FINE (Analog input only) Improves focus, clarity and image stability by increasing or decreasing this setting. If the “AUTO ADJUST” function and the “H.SIZE” function do not give you a satisfactory picture setting, a fi ne tuning can be performed by using the “FINE” function. For this a Moiré test pattern could be used. If ...

  • NEC MultiSync EA294WMi - page 17

    English-15 English Color Color Control System: Color presets select the desired color setting. 1, 2, 3, 5: Increases or decreases Red, Green or Blue color depending upon which is selected. The change in color will appear on screen and the direction (increase or decrease) will be shown by the bars. NA TIVE: Original color presented by the LCD panel ...

  • NEC MultiSync EA294WMi - page 18

    English-16 RESPONSE IMPRO VE T urns the Response Improve function on or off. Response Improve may reduce blurring that occurs in some moving images. OFF TIMER Monitor will automatically power down when you have selected a pre-determined amount of time. Before powering off, a message will appear on the screen asking if you want to delay the turn of ...

  • NEC MultiSync EA294WMi - page 19

    English-17 English D A T A COPY T o initiate data copy from the master monitor to the sub monitor(s), select “DA T A COPY” and touch “SELECT”. A “PROCEEDING...” indicator will appear on the screen. NO TE: This function is only intended for the master monitor in ControlSync. All of the settings specifi ed in the ControlSync chart (see p ...

  • NEC MultiSync EA294WMi - page 20

    English-18 Specifi cations Monitor Specifi cations MultiSync EA294WMi Notes LCD Module Diagonal: Viewable Image Size: Native Resolution (Pixel Count): 73.02 cm/29 inches 73.02 cm/29 inches 2560 x 1080 Active matrix; thin fi lm transistor (TFT) liquid crystal display (LCD); 0.263 mm dot pitch; 300 cd/m 2 white luminance; 1000:1 contrast ratio (ty ...

  • NEC MultiSync EA294WMi - page 21

    English-19 English Features DisplayP or t: DisplayPort is designed to be the future-ready and scalable solution for high performance digital display connectivity . It enables the highest resolutions, the fastest refresh rates and deepest color depths over standard cables. MHL: MHL (Mobile High Defi nition Link) is designed for a mobile audio/video ...

  • NEC MultiSync EA294WMi - page 22

    English-20 T roub leshooting No picture • The signal cable should be completely connected to the display card/computer . • The display card should be completely seated in its slot. • The monitor does not support DisplayPort converter signal. • Front Power Switch and computer power switch should be in the ON position. • The monitor will au ...

  • NEC MultiSync EA294WMi - page 23

    English-21 English No Video • If no video is present on the screen, turn the Power Key off and on again. • Make certain the computer is not in a power-saving mode (touch the keyboard or mouse). • Some video cards do not output video signal when monitor is turned OFF/ON or disconnect/connect from the AC power cord under low resolution with Dis ...

  • NEC MultiSync EA294WMi - page 24

    English-22 Using the A uto Brightness function The brightness of the LCD screen can be set to increase or decrease depending on the amount of ambient light within the room. If the room is bright, the monitor becomes correspondingly bright. If the room is dim, then the monitor will dim accordingly . The purpose of this function is to make the viewin ...

  • NEC MultiSync EA294WMi - page 25

    English-23 English Using Picture b y Picture (PBP) Function This monitor can display split screens from two sources by using any one of the input combinations shown on page 15. NO TE: Please see PBP MODE (page 15) and PBP TYPE (page 15). The following settings are set to be the same for both screens: BRIGHTNESS, AUTO BRIGHTNESS, OFF MODE SETTING, H ...

  • NEC MultiSync EA294WMi - page 26

    English-24 Using the Zoom Function Allows you to use the entire screen area, signifi cantly expanding the size. Allows the picture displayed in the center to expand. NO TE: When in PBP MODE, the sub picture is expanded or reduced automatically . SETUP 1. Select FULL or ASPECT in EXP ANSION to activate the Zoom function (see page 14). EXP ANSION OF ...

  • NEC MultiSync EA294WMi - page 27

    English-25 English B. The left image is set to be the main one. In this case, the priority image is set to be on the left side. The size of the image on the right side with black area is reduced. T o enlarge the split images: use the following procedures to reduce the black area and enlarge the split images. 1. In case A, a priority image is set to ...

  • NEC MultiSync EA294WMi - page 28

    English-26 Contr olSync 1. Connect the master monitor with a sub monitor via a ControlSync cable (ø 2.5) into ControlSync IN/OUT . 2. Follow the steps of DA T A COPY . When the setting of the master monitor is adjusted, it will be copied and sent to the connected sub monitor(s) automatically . 3. Up to 5 sub monitors can be daisy-chained via Contr ...

  • NEC MultiSync EA294WMi - page 29

    English-27 English TCO Cer tifi ed Edg e Displa ys 1.2 Congratulations! This product is TCO Certifi ed – for Sustainable IT TCO Certi Þ ed is an international third party sustainability certi Þ cation for IT products. TCO Certi Þ ed ensures that the manufacture, use and recycling of IT products re ß ect environmental, social and economic re ...

  • NEC MultiSync EA294WMi - page 30

    English-28 NEC DISPLA Y SOLUTIONS is strongly committed to environmental protection and sees recycling as one of the company’ s top priorities in trying to minimize the burden placed on the environment. We are engaged in developing environmentally- friendly products, and always strive to help defi ne and comply with the latest independent standa ...

Fabbricante NEC Categoria Monitor

I documenti che otteniamo dal fabbricante del dispositivoNEC MultiSync EA294WMi possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici NEC
- manuali per l’uso MultiSync EA294WMi
- schede prodotto NEC
- opuscoli
- o etichette energetiche NEC MultiSync EA294WMi
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso NEC MultiSync EA294WMi.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione NEC MultiSync EA294WMi, manuali di manutenzione, brevi manuali o manuali utente NEC MultiSync EA294WMi. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto NEC MultiSync EA294WMi.

Manuali per l’uso simili

Manuale completo del dispositivo NEC MultiSync EA294WMi, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare NEC MultiSync EA294WMi dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti NEC MultiSync EA294WMi.

Il manuale per l’uso completo NEC, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale NEC MultiSync EA294WMi - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice NEC MultiSync EA294WMi, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per NEC MultiSync EA294WMi che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo NEC MultiSync EA294WMi - che ci dovrebbe aiutare nei primi passi durante l'uso NEC MultiSync EA294WMi
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del NEC MultiSync EA294WMi
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio NEC MultiSync EA294WMi in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su NEC MultiSync EA294WMi?

Utilizza il modulo sottostante

Se non hai risolto il problema con NEC MultiSync EA294WMi con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con NEC MultiSync EA294WMi è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)