Italiano dropdown-ico

Manuale per l’uso Jet HBS-56S

28 pagine 2.62 mb
Scarica

Vai alla pagina of 28

Summary
  • Jet HBS-56S - page 1

    Operating Instructions and Parts Manual 5 x 6-inch Horizontal Band Saw Model HBS-56S For use with machines wit h Serial Numbers 06080307 and hig her WMH TOOL GROUP 2420 Vantage Drive Elgin, Illinois 60124 Part No. M-414457A Ph.: 800-274-6848 Revision B 9/06 www.wmhtoolgroup.com Copyright © WMH Tool Group ...

  • Jet HBS-56S - page 2

    2 Warranty and Service WMH Tool Group, Inc., warrants every product it se lls. If one of our tools nee ds service or repair, one of our Authorized Service Centers lo cated throughout the United States can giv e you qu ick service. In most cases, any of these WMH Tool Group Authorized Servic e Centers can authorize warranty repair, assist you in obt ...

  • Jet HBS-56S - page 3

    3 Table of Contents Warranty and Service ........................................................................................................... ......................... 2 Table of Contents .............................................................................................................. ............................ 3 Warning ..... ...

  • Jet HBS-56S - page 4

    4 Warning 1. Read and understand the entire o wner's manual bef ore attempting assembly or operation. 2. Read and understand the warnings posted on the ma chine and in this manual. Failure to comply with all of these warnings may cause seri ous injury. 3. Replace the warning labels if they become obscu red or removed. 4. This band saw is d esi ...

  • Jet HBS-56S - page 5

    5 blahblahblah 20. Make your workshop child proof with padlocks , master switc hes or by removing starter keys. 21. Give your work undivided attention. Loo king aroun d, carrying on a conversation and “horse-play” a re careless acts that can result in seriou s injury. 22. Maintain a balanced stan ce at all times so that you do not fall or le an ...

  • Jet HBS-56S - page 6

    6 Introduction This manual is provided by WMH Tool Grou p covering the safe operation and maintenance procedures for a JET Model HBS-56S Horizontal Band Saw. Thi s ma nual contains in structions on installation, safety precautions, general o perating procedures, m aintenance instructio ns and part s breakdown. This m achine has been designed and co ...

  • Jet HBS-56S - page 7

    7 Shipping Contents Open carton and check for shipping damage. Report any damage immediately to your distributor and shipping a gent. Do not discard any shipping material until the band saw i s assembled and running pr operly. Contents of the Carton 0 1 Band Saw (not shown) 0 1 Side Plate - left (A) 0 1 Side Plate - right (B) 0 1 Front Door (C) 0 1 ...

  • Jet HBS-56S - page 8

    8 Read and understand the entire conte nts of this manual before attempting set-up or operation! Failure to comply may cause serious injury. Assembly of Stand Tools required for assembl y: Two 1/2-inch wrench ( Note: A ratchet wren ch may speed assembly time.) 1. Asse mble left (A) and right (B) side p lates with six 5/16"x3/4" hex cap sc ...

  • Jet HBS-56S - page 9

    9 Assembly of Band Saw Tools required for assembl y: – cross point (Phillips) screwdriver – 3mm and 4mm hex wrenches (p rovided) – 1/2" and 9/16" wrenches Remove any plastic or holding straps from around the band saw. Area s of the machine have been given a protective coatin g at the factory. This should be removed using a soft clot ...

  • Jet HBS-56S - page 10

    10 4. Lift up on the motor and install the belt around the pulley groov es, as shown in Figure 4. Allow the motor to dro p back down, then push it down farther to tension the belt. (For further information o n belt tension and belt position on the grooves, see page 15.) 5. Tighten the knob (A, Figure 3). 6. Close the pulley cover and se cure it wit ...

  • Jet HBS-56S - page 11

    11 This band saw is pre-wired for 115 volt and is equipped with an electric cord having an equipment-grounding conductor and a grounding plug similar to that sho wn in Figure 6. The plug must be inserted into a matchin g outlet that is properly installed and gro unded in accordance with all local codes and ordinan ces. Do not modify the plug provid ...

  • Jet HBS-56S - page 12

    12 1. Disconnect machine from powe r source. 2. Open the switch b ox and connect the lead s according to th e wiring dia gram inside the switch box. This diagram is also shown on page 26 of this manual. 3. The 115V attachment plug sup plied with the band saw must be replaced with a UL listed plug suitable for 230 volt operation, si milar to the one ...

  • Jet HBS-56S - page 13

    13 4. If the vise and bla de are square but the pointer (D, Figure 10) i s off slightly, loosen the screw and adjust the pointer until it line s up with zero on the scale. Tighten the screw. NOTE: The handle (A, Fig ure 10) is adj ustable. Simply lift up on the handle and rotate it on the pin. Release the handle, making sure it se ats itself proper ...

  • Jet HBS-56S - page 14

    14 3. Slide the movable jaw by hand until the jaw contacts the workpiece. 4. Rotate the vise handwhee l clockwise to re- engage the lead screw, and continue the tightening process of the jaw until the workpiece is securely clam ped. 5. The quick rel ease function can be used to back off the movable jaw when the cut is finished. Miter Cuts There are ...

  • Jet HBS-56S - page 15

    15 Blade Tension Use the knob (Figure 15 ) to tension the blade. Clockwise tightens the blade, co unterclockwise loosens it. Blade Tracking Tracking the blade requires that the band sa w be operating while the back blade cover is remov ed. Use extreme caution and keep hands a w ay from blade. The blade provided with your band saw ha s already been ...

  • Jet HBS-56S - page 16

    16 Belt Tension 1. Disconnect band saw from power source. 2. Open the pulley cover. 3. Loosen the knob (see A, Figure 3 ), and push down on the motor to tighten the belt. 4. Tighten the knob (A, Figure 3). 5. Check the tension by usin g moderate finger pressure about midway between the pulleys. The belt should deflect about 1/2”. See Figure 17. 6 ...

  • Jet HBS-56S - page 17

    17 Blade Replacement Use caution and proceed slowly when w orking with or around a band saw blade. Use gloves when handling it. 1. Disconnect band saw from power source. 2. Remove the knob and the back blade cover from the band saw. See Figure 19. 3. Loosen the handl e on the blade guide (A, Figure 18) and lower the blade gui de as far as it will g ...

  • Jet HBS-56S - page 18

    18 Vertical Bow Position 1. The band saw can be placed in vertical position to facilitate blade ch anges, maintenance, etc. Unscrew the knob (Fi gure 22) and slide it out t o disengage the hydraulic cylinder. 2. Raise the bow all the way. 3. The sto p screw (Figure 23) has been pre- set at the factory. If further adjustments are needed, loosen the ...

  • Jet HBS-56S - page 19

    19 5. Open the valve on the hy draulic cylinder to allow the bow to descen d in a gradual an d controlled manner. 6. The machine will shut off at the completion of the cut. Remove the workpiece. 7. Close the hydraulic cylinder valve, and raise the bow in preparation for the next cut. Maintenance Before doing maintenance on the machine, disconnect i ...

  • Jet HBS-56S - page 20

    20 Troubleshooting Trouble Probable Cause Remedy No incoming power. Check plug connection. Blown electrical panel fuses. Replace fuses. Motor will not start. Defective motor, switch, power cable, or plug. Qualified electrician/service personnel should inspect these items. Stand on uneven surface. Adjust stand for even support. Saw blade has cracks. ...

  • Jet HBS-56S - page 21

    21 Parts List: HBS-56S Band Saw Index No. Part No. Description Size Qty 1 ............... TS-0051031 ............. Hex Ca p Bolt ........................................................ 5/16”x3/4” .......... .......... 4 2 ............... TS-0561011 ............. Hex Nut ................................................................ 1/4” .. ...

  • Jet HBS-56S - page 22

    22 Parts List: HBS-56S Band Saw Index No. Part No. Description Size Qty 89 ............. OS-15375................. Oil Seal................................................................. .............. ...................... 2 90 ............. HVBS462-090 .......... Transmi ssion Wheel Shaft ................................... ................... ...

  • Jet HBS-56S - page 23

    23 Parts List: HBS-56S Band Saw Index No. Part No. Description Size Qty 313 ........... TS-0208071 ............. Hex Socket Head Screw ...................................... 5/ 16"x1-1/4" ................ 2 314 ........... TS-0267041 ............. Set Screw ............................................................. 1/4"x3/8". ...

  • Jet HBS-56S - page 24

    24 Parts List Index No. Part No. Description Size Qty 393 ........... HBS56S-393 ............ Wire Ring ............................................................. ..................... ............... 1 394 ........... TS-081C032 ............. Cross Round He ad Screw ................................... 10- 24x1/2” ................... 1 395 ... ...

  • Jet HBS-56S - page 25

    25 Bow Assembl y (Page 2 of 3) 97-1(2) ...

  • Jet HBS-56S - page 26

    26 Bow Assembl y (Page 3 of 3) ...

  • Jet HBS-56S - page 27

    27 Base and Cabinet Assembly ...

  • Jet HBS-56S - page 28

    28 Electrical Connections WMH Tool Group 2420 Vantage Drive Elgin, Illinois 60124 Phone: 800-274-6848 www.wmhtoolgroup.co m ...

Fabbricante Jet Categoria Saw

I documenti che otteniamo dal fabbricante del dispositivoJet HBS-56S possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Jet
- manuali per l’uso HBS-56S
- schede prodotto Jet
- opuscoli
- o etichette energetiche Jet HBS-56S
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Jet HBS-56S.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Jet HBS-56S, manuali di manutenzione, brevi manuali o manuali utente Jet HBS-56S. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Jet HBS-56S.

Manuali per l’uso simili

Manuale completo del dispositivo Jet HBS-56S, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Jet HBS-56S dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Jet HBS-56S.

Il manuale per l’uso completo Jet, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Jet HBS-56S - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Jet HBS-56S, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Jet HBS-56S che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Jet HBS-56S - che ci dovrebbe aiutare nei primi passi durante l'uso Jet HBS-56S
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Jet HBS-56S
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Jet HBS-56S in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Jet HBS-56S?

Utilizza il modulo sottostante

Se non hai risolto il problema con Jet HBS-56S con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Jet HBS-56S è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)