Italiano dropdown-ico

Manuale per l’uso American International PG10*34-150-2NV or 2PV

32 pagine 5.11 mb
Scarica

Vai alla pagina of 32

Summary
  • American International PG10*34-150-2NV or 2PV - page 1

    1 This manual covers model numbers: United States Canada PG10* 34-100-2NV or 2PV PG10* 34-130-2NV or 2PV PG10* 50-130-2NV or 2PV PG10* 34-150-2NV or 2PV PG10* 50-175-3NV or 3PV PG10* 50-199-3NV or 3PV PG10* 100-199-3NV or 3PV PR 100-34 2NV or 2PV PR 130-34 2NV or 2PV PR 130-50 2NV or 2PV PR 150-34 2NV or 2PV PR 175-50 3NV or 3PV PR 199-50 3NV or 3P ...

  • American International PG10*34-150-2NV or 2PV - page 2

    2 Y our safety and the safety of others are very important. We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages. This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety aler ...

  • American International PG10*34-150-2NV or 2PV - page 3

    3 INST ALLA TION INSTRUCTIONS Consumer Information OBSERVE ALL GOVERNING CODES AND ORDINANCES. This water heater is design-certified by CSA International as a Category IV , direct vented water heater which takes its combustion air from the outside of the structure and exhausts all products of combustion to the outside of the structure. This water h ...

  • American International PG10*34-150-2NV or 2PV - page 4

    4 Location Requirements The water heater design has been tested by CSA International and complies with ANSI Z21.10.1, Section 2.35 Flammable V apors Resistance. In garage installation avoid damage to your water heater by installing a vehicle stop as shown in figure below . Check state and local codes for requirements prior to installation. Importan ...

  • American International PG10*34-150-2NV or 2PV - page 5

    5 CONDENSA TE LINE Important: Do not run the condensate drain in areas that are likely to freeze. Frozen condensate will block the drain line and result in property damage or water heater malfunction. Condensate T rap Assembly A condensate trap/drain stem assembly has been supplied with the water heater and is located behind the access door inside ...

  • American International PG10*34-150-2NV or 2PV - page 6

    6 Condensate Drain Line All parts of the condensate trap are glued except for the 1/2” CPVC drain stem joint at the elbow (see figure 3). This assembly can be turned with the outlet of the tee oriented as needed. Once orientation direction is decided, remove the unglued joint from the elbow at the bottom and apply a suitable cement to joint. Re-i ...

  • American International PG10*34-150-2NV or 2PV - page 7

    7 V ent Pipe Material The following plastic materials may be used for both the combustion air inlet and exhaust outlet piping subject to state and local codes: • Schedule 40 PVC or ABS • Schedule 40 or 80 CPVC • DWV Pipe is acceptable Note: Use only solid (not foam core) piping. Plastic pipe and fittings are available through most plumb- ing ...

  • American International PG10*34-150-2NV or 2PV - page 8

    8 V ent T ermination Locations The air inlet and exhaust outlet must be installed with the following minimum clearances (see figure 6): • T welve inches above grade or maximum anticipated snow level. • T welve inches from any opening through which flue gases could enter the structure. • Four feet horizontally and vertically from gas or electr ...

  • American International PG10*34-150-2NV or 2PV - page 9

    9 INLET/OUTLET VENT TERMINA TIONS (100,000 - 150,000 BTU/HR) Standard Horizontal T ermination When 3 inch pipe is used between the water heater and the outside wall, reduce it to 2 inch pipe before penetrating the wall. A maximum of 18 inches of 2 inch pipe may be used between the 3 inch transition and the inside of the wall (see figure 7A). The st ...

  • American International PG10*34-150-2NV or 2PV - page 10

    10 VERTICAL TERMINA TIONS (100,000 - 150,000 BTU/HR) When 3 inch pipe is used between the water heater and the roof, reduce it to 2 inch pipe before penetrating the roof. A maximum of 18 inches of 2 inch pipe may be used between the 3 inch transition and the inside of the roof. The vertical inlet air termination requires a return bend or two short ...

  • American International PG10*34-150-2NV or 2PV - page 11

    11 CONCENTRIC VENT TERMINA TIONS (100,000 - 150,000 BTU/HR) For new installations, install 2” Concentric vent kit model KGA VT0501CVT , part number 6910542. See Manufacturer ’s instructions for complete installation or call customer service at 1-800-456-9805 for assistance. For planning purposes, see figures 10A-13A below for vent terminal spec ...

  • American International PG10*34-150-2NV or 2PV - page 12

    12 INLET/OUTLET VENT TERMINA TIONS (175,000+ BTU/HR) Figure 8B: Alternative Horizontal T ermination (175,000+ BTU/Hr or greater input models) Figure 7B: Standard Horizontal T ermination (175,000+ BTU/Hr models) Standard Horizontal T ermination The standard horizontal air inlet termination is a 3 inch pipe which terminates at the exterior wall and u ...

  • American International PG10*34-150-2NV or 2PV - page 13

    13 VERTICAL TERMINA TIONS (175,000+ BTU/HR) Figure 9B: V ertical T ermination (175,000+ BTU/Hr models) For inputs of 175,000 BTU/Hr or greater , all termination pip- ing and fittings are 3”. Do not reduce before penetrating the wall. The vertical inlet air termination requires a return bend or two short or long sweep radius 90° elbows to keep th ...

  • American International PG10*34-150-2NV or 2PV - page 14

    14 CONCENTRIC VENT TERMINA TIONS (175,000 + BTU/HR) Figure 10B: 3 Inch Concentric V ent For new installations, install 3” Concentric vent kit model KGA VT0601CVT , part number 6910543. See Manufacturer ’s instructions for complete installation or call customer service at 1-800-456-9805 for assistance. For planning purposes, see figures 10B-13B ...

  • American International PG10*34-150-2NV or 2PV - page 15

    15 Figure 14: Input Graph Gas Input Rate The gas input rate of this water heater is affected by several environmental factors such as: • The heating value of the gas • The air and gas densities (which vary widely due to baro- metric pressure and temperature changes) • V enting installations (pipe diameter , length and fittings) • Altitude W ...

  • American International PG10*34-150-2NV or 2PV - page 16

    16 Figure 15: T ypical One-T emperature System Piping Installation T empering V alve Installation A tempering valve has been provided for use with the Polaris® Gas water heater and must be installed, per the manufacturer ’s instructions, in the domestic hot water line. See Figure 16 for a sample tempering valve installation. General Information ...

  • American International PG10*34-150-2NV or 2PV - page 17

    17 • If the space heating system requires water temperatures in excess of 120°F , a tempering valve (provided) must be installed per the manufacturer ’s instructions in the potable hot water supply to limit the risk of scald injury . • Pumps, valves, piping and fi ttings must be compatible with potable water . • A properly installed fl o ...

  • American International PG10*34-150-2NV or 2PV - page 18

    18 T emperature and Pressure Relief V alve For protection against excessive pressures and tempera- tures, a temperature and pressure relief valve must be installed in the opening marked “T & P RELIEF V AL VE”. This valve must be design certified by a nationally recog- nized testing laboratory that maintains periodic inspection of the produc ...

  • American International PG10*34-150-2NV or 2PV - page 19

    19 GAS SUPPL Y AND PIPING Gas Requirements Read the data plate to be sure the water heater is made for the type of gas being used. This information will be found on the data plate located on the front of the water heater . If the information does not agree with the type of gas available, do not install or operate the water heater . Call your dealer ...

  • American International PG10*34-150-2NV or 2PV - page 20

    20 Gas Pressure T esting Important : This water heater and its gas connection must be leak tested before placing the appliance in operation. •  If the code requires the gas lines to be tested at a pressure of 14” W .C. or greater , the water heater and its manual shut-off valve must be disconnected from the gas supply piping system and the l ...

  • American International PG10*34-150-2NV or 2PV - page 21

    21 Electrical Shock Hazard Disconnect power before servicing. Replace all parts and panels before operating. Failure to do so can result in death or electrical shock. ELECTRICAL CONNECTIONS Figure 20A: Electrical Connections (34/50 Gal.) If you lack the necessary skills required to properly install the electrical wiring to this water heater , do no ...

  • American International PG10*34-150-2NV or 2PV - page 22

    22 WIRING DIAGRAM MODELS 130,000 BTU/Hr & Below NOTICE: IF ANY OF THE ORIGINAL WIRE AS SUPPLIED WITH THE APPLIANCE MUST BE REPLACED, IT MUST BE REPLACED WITH 18 GAUGE STRANDED 105C WIRE OR ITS EQUIV ALENT . THERMOST A T BOARD IGNITION CONTROL IGNITION CONTROL BLOWER HSI HSIG L1 L2 IND 120 V AC 24 V AC GAS V ALVE RELA Y RED LED GREEN LED YELLOW ...

  • American International PG10*34-150-2NV or 2PV - page 23

    23 INST ALLA TION CHECKLIST W ater Heater Location Requirements  Centrally located with the water piping system. Located as close to the gas piping and vent pipe system as pos- sible.  Located indoors and in a vertical position. Protected from freezing temperatures.  Proper clearances from combustible surfaces main- tained and not installe ...

  • American International PG10*34-150-2NV or 2PV - page 24

    24 OPERA TING YOUR W A TER HEA TER Read and understand these directions thoroughly before attempting to operate the water heater (see Operating Instructions on page 25). Check the data plate on the front of the water heater for the correct gas. Do not use this water heater with any gas other than the one listed on the data plate. If you have any qu ...

  • American International PG10*34-150-2NV or 2PV - page 25

    25 Stacking Stacking occurs when a series of short draws of hot water (3 gallons or less) are taken from the water heater tank. This causes increased cycling of the burner and can result in increased water temperatures at the hot water outlet. A tempering valve must be installed in the hot water supply line to reduce the risk of scald injury . W at ...

  • American International PG10*34-150-2NV or 2PV - page 26

    26 OPERA TIONAL CONDITIONS MAINTENANCE W ater Heater Sounds During the normal operation of the water heater , sounds or noises may be heard. These noises are common and may result from the following: 1. Normal expansion and contraction of metal parts during periods of heat-up and cool-down. 2. Sediment buildup in the tank bottom will create varying ...

  • American International PG10*34-150-2NV or 2PV - page 27

    27 MAINTENANCE OF YOUR W A TER HEA TER 3 Month Inspection At least every 3 months, a visual inspection should be made of the combustion air inlet as well as the exhaust and water piping. Check the water heater for the following: • Obstructions, damage, or deterioration in the venting system. Make sure the exhaust and combustion air supplies are n ...

  • American International PG10*34-150-2NV or 2PV - page 28

    28 TROUBLESHOOTING Ignition Control Module (ICM) LED Error Codes: (Flashes visible through viewport in access door) FLASHES INDICA TED PROBLEM CONTROL REACTION 1 Pressure Switch Closed SC* 2 Pressure Switch Open SL 3 Failed Ignition SL3 4 Gas V alve Hardware Fault SL 5 Flame Sense Hardware Fault SC 6 False Flame SL** 8 Ignition Control Hardware Fau ...

  • American International PG10*34-150-2NV or 2PV - page 29

    29 SOFTW ARE OPERA TION SEQUENCE IGNITION CONTROL MODULE SOFTW ARE OPERA TION SEQUENCE * For 175,000 BTU/Hr models and above the flame establishing period is six seconds. For the first 3 seconds the gas valve is off. ...

  • American International PG10*34-150-2NV or 2PV - page 30

    30 REP AIR P ARTS LIST/DIAGRAM ITEM NO. P ARTS DESCRIPTION 1 1” NPT x 3” BRASS NIPPLE 2 THERMOST A T SENSOR BUSHING 3 O-RING 4 THERMOST A T SENSOR/ECO 5 INVERTED FLARE NUT 6 PLUG 7 VINYL TUBING 8 PRESSURE SWITCH 9 COMBUSTION BLOWER 10 4 INCH DIAMETER BLOWER GASKET 11 BURNER (NA TURAL AND L.P . SAME) 12 6 INCH DIAMETER BURNER GASKET 13 HOT SURF ...

  • American International PG10*34-150-2NV or 2PV - page 31

    31 REP AIR P ARTS LIST/DIAGRAM ITEM NO. P ARTS DESCRIPTION 1 1-1/2” NPT x 3” BRASS NIPPLE 2 THERMOST A T SENSOR BUSHING 3 THERMOST A T SENSOR/ECO 4 CONTROL P ANEL HOUSING 5 IGNITION CONTROL 6 BLOWER ISOLA TION RELA Y 7 THERMOST A T BOARD 8 TRANSFORMER 9 SIGHT GLASS 10 RED LED 11 YELLOW LED 12 GREEN LED 13 TEMPERA TURE SELECTOR KNOB 14 THERMOST ...

  • American International PG10*34-150-2NV or 2PV - page 32

    32 POLARIS MODELS & DIMENSIONS C lea n-out P ort MODEL NUMBER GAL. CAP . INPUT (MBTU PER HR.) VENT DIA. EXTERIOR W A TER CONNECTIONS T&P HGT GAS SUPPL Y AIR INLET/ EXHAUST APPROX SHIP . WEIGHT A B C D E F G PG10 34-100-2NV OR 2PV 34 100 2 OR 3 48-1/2 22 15-3/4 40-1/2 41 6-3/8 5-1/2 / 6-5/8 150 PG10 34-130-2NV OR 2PV 34 130 2 OR 3 48-1/2 22 ...

Fabbricante American International Categoria Water Heater

I documenti che otteniamo dal fabbricante del dispositivoAmerican International PG10*34-150-2NV or 2PV possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici American International
- manuali per l’uso PG10*34-150-2NV or 2PV
- schede prodotto American International
- opuscoli
- o etichette energetiche American International PG10*34-150-2NV or 2PV
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso American International PG10*34-150-2NV or 2PV.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione American International PG10*34-150-2NV or 2PV, manuali di manutenzione, brevi manuali o manuali utente American International PG10*34-150-2NV or 2PV. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto American International PG10*34-150-2NV or 2PV.

Manuali per l’uso simili

Manuale completo del dispositivo American International PG10*34-150-2NV or 2PV, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare American International PG10*34-150-2NV or 2PV dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti American International PG10*34-150-2NV or 2PV.

Il manuale per l’uso completo American International, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale American International PG10*34-150-2NV or 2PV - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice American International PG10*34-150-2NV or 2PV, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per American International PG10*34-150-2NV or 2PV che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo American International PG10*34-150-2NV or 2PV - che ci dovrebbe aiutare nei primi passi durante l'uso American International PG10*34-150-2NV or 2PV
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del American International PG10*34-150-2NV or 2PV
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio American International PG10*34-150-2NV or 2PV in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su American International PG10*34-150-2NV or 2PV?

Utilizza il modulo sottostante

Se non hai risolto il problema con American International PG10*34-150-2NV or 2PV con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con American International PG10*34-150-2NV or 2PV è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)