Italiano dropdown-ico

Manuale per l’uso Wagner SprayTech 505

33 pagine 2.54 mb
Scarica

Vai alla pagina of 33

Summary
  • Wagner SprayTech 505 - page 1

    1 PRINTED IN THE U. S. A. R Form No. 0270993-11/93 505 HIGH PERFORMANCE AIRLESS SPRA YER Questions? ... Need Help? Wagner maintains a toll-free help line for you should you have any comments or problems with this Wagner product. Call us first ....for answers fast... Wagner Technical Service 1-800-328-8251 Hours: Weekdays: 8:00 - 4:30 Central Time W ...

  • Wagner SprayTech 505 - page 2

    2 CONTENTS General Description ....................................................... 2 Safety Precautions ...................................................... 3-6 Extension Cord ............................................................... 7 Grounding Instructions ................................................... 7 Pressure Relief Procedure ...

  • Wagner SprayTech 505 - page 3

    3 SAFETY PRECAUTIONS This manual contains information which must be read and understood before using the equipment. When you come to an area which has one of the following symbols, pay particular attention and make certain to heed the safeguard. WARNING Important safety information indicates a hazard which may cause serious injury or loss of life. ...

  • Wagner SprayTech 505 - page 4

    4 WARNING PREVENTION HAZARD • Maximum operating range of the gun - 2500 PSI fluid pressure. • NEVER aim the gun at any part of the body. • NEVER allow any part of the body to come in contact with the fluid stream. DO NOT come in contact with a fluid stream created by a leak in the fluid hose. • NEVER put hand in front of the gun. Gloves wil ...

  • Wagner SprayTech 505 - page 5

    5 Explosion or fire - Solvent and paint fumes can explode or ignite, causing property damage and or severe injury. WARNING HAZARD PREVENTION • Exhaust and fresh air introduction must be provided to keep the air within the spray area free from accumulation of flammable vapors. • Avoid all ignition sources such as static electricity sparks, open ...

  • Wagner SprayTech 505 - page 6

    6 WARNING PREVENTION HAZARD Explosion hazard incompatible materials - May cause property damage or severe injury. Hazardous vapors - Paints, solvents, insecticides, and other materials may be harmful if inhaled causing se- vere nausea, fainting, or poisoning. General - May cause property damage or severe injury. • DO NOT USE BLEACH. • DO NOT us ...

  • Wagner SprayTech 505 - page 7

    7 NOTE: More than 100 feet of extension cord is not recommended. Use more paint hose, not more extension cord. Shorter extension cords will assure maximum electrical power for proper operation. Grounding Instructions This product must be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing ...

  • Wagner SprayTech 505 - page 8

    8 Pressure Relief Procedure Follow this procedure after the unit is assembled and before any operation which involves the spray gun such as changing tips or accessories, or cleaning and maintenance. 1. Make sure PRESSURE CONTROL KNOB is at its lowest setting ( counte rclockwise). 2. Turn PRIMING KNOB to PRIME A position. 3. Trigger gun to remove an ...

  • Wagner SprayTech 505 - page 9

    9 Pail Bracket SET -UP Figure 3B - Attaching Cart Handle Bolt, washer and wing nut Cart Handle ASSEMBLE CART 2. Attach cart handle (3). Face the hose hook toward the front of the unit. Use two bolts, washers and wing nuts (4), tightening securely. See Figure 3B. Figure 2 – Cart Assembly Diagram 4 2 Tools needed: Some assembly is required to get y ...

  • Wagner SprayTech 505 - page 10

    10 SET -UP 1. Lock gun. See Figure 4. Figure 4 - Gun in Locked & Unlocked Position A TT ACH TIP T O GUN 2. If spray tip is not pre- assembled, (See Figure 5) insert tip (1) into tip guard, (2) and turn 90 ° coun- ter clockwise to spray position (arrow pointing away from gun). Cylinder of tip forms a stop for the seal (3). Insert seal (3) align ...

  • Wagner SprayTech 505 - page 11

    11 SET -UP A TT ACH RETURN HOSE 1. Be sure motor switch is turned OFF . 2. Screw brass fitting of return tube into upper port on side of pump. (The brass fitting is located in the literature set.) Tighten firmly by hand. See figure above. 3. Press return tube (small tube) to brass fitting and fasten with clamp. See Figure 9. A TT ACH P AINT HOSE 1. ...

  • Wagner SprayTech 505 - page 12

    12 PRIMING 1. Lay unit back on its handle so inlet valve is facing up. Fill inlet valve with water or light household oil. 2. Make sure Prime/Spray Knob is in Prime A position and Pressure Knob is turned to the lowest pressure. (Counter clockwise) See Figure 11. Turn unit on. Pressure Control Knob Prime A /Spray B Knob Hose Port Inlet Valve Facing ...

  • Wagner SprayTech 505 - page 13

    13 Figure 17 - Attaching Paint Pail Handle PRIME THE PUMP 1. Attach Suction Tube to inlet valve and tighten firmly by hand. See Figure 15. Be sure threads are straight so the fitting turns freely without binding. Figure 15 - Attaching Suction Tube 2. Place suction tube and return tube in paint. See Figure 16. 1. Make sure the PRESSURE CONTROL KNOB ...

  • Wagner SprayTech 505 - page 14

    14 PRIMING 3. TURN SPRAYER ON. 4. Turn PRESSURE CONTROL KNOB between half and full pressure. See Figure 20. You should then be able to see the paint move through the suction tube to the pump. Continue until paint flows through the return tube. (Let unit prime 1 to 2 minutes). Figure 20 - Turn Pressure Control Knob CAUTION the priming knob. Failure ...

  • Wagner SprayTech 505 - page 15

    15 SPRA YING Figure 24 - Paint Tailing Pattern GOOD SPRAY PATTERN PRACTICE FIRST 1. Be sure paint hose is free of kinks and clear of traffic or objects with sharp cutting edges. 2. Return PRESSURE CONTROL KNOB to its lowest setting ( counter clockwise). Figure 21. 3. Turn PRIMING KNOB to SPRAY B position. Figure 22. 4. Turn PRESSURE CONTROL KNOB co ...

  • Wagner SprayTech 505 - page 16

    16 SPRA YING 1. The key to a good paint job is an even coating over the entire surface. With spray painting, this is done by using even strokes, with your arm moving at a con- stant speed and keeping the spray gun a constant distance from the surface. 2. In most cases, the best spraying distance is 10 to 12 inches between the spray tip and the surf ...

  • Wagner SprayTech 505 - page 17

    17 5. The spray gun should be triggered off at the end of each stroke and on again at the beginning of the next. This avoids paint buildup at the end of the stroke which may result in runs and sags. Triggering at the end of the stroke also saves paint and results in a better looking job. See Figure 28. Start Stroke Pull Trigger End Stroke Release T ...

  • Wagner SprayTech 505 - page 18

    18 Figure 32 - Remove And Clean Screen SPRA YING Continued from page 17 Cleaning The Spray Gun Filter The spray gun includes a filter to catch particles before they reach the spray tip. If this filter becomes clogged or obstructed it will reduce the flow of paint, changing the spray pattern and possibly damaging the filter. This filter must be clea ...

  • Wagner SprayTech 505 - page 19

    19 SHORT -TERM/OVERNIGHT ST ORAGE Shut-down 1. Lock the gun and reduce the pressure. Turn the sprayer to prime A and shut it off. Unplug sprayer. Leave the suction set in the paint. Refer to Pressure Relief Procedure. 2. For latex materials only , pour 1/2 cup water slowly on the top of the paint to prevent the paint from drying. For other material ...

  • Wagner SprayTech 505 - page 20

    20 Do not allow paint to build up on the motor. Overheating of the motor will result. Do not allow flammable solvents to come in contact with the motor, which could ignite. NOTE: You will need an extra bucket with cleaning solution, a toothbrush, an adjustable wrench and rags. CLEANUP WARNING SHUT DOWN/CLEAN UP 1. Lock the gun and reduce the pressu ...

  • Wagner SprayTech 505 - page 21

    21 15. Attach paint hose to gun,tighten with two wrenches. CLEAN UP 14. Clean spray tip and gun filter with a soft brush. Reassemble spray tip in cleaning position. (Arrow points to back of the gun.) 16. Turn the unit on and unlock gun trigger. Turn to Spray B and point gun to side of cleaning bucket. 18. Release and lock trigger, reduce pressure, ...

  • Wagner SprayTech 505 - page 22

    22 CLEAN UP 21. Lock gun, reduce pressure and turn Prime/Spray Knob to prime A . 22. Lay unit back on handle so inlet valve is facing upward. Clean threads of inlet valve with a damp cloth. Fill inlet valve with light household oil. See Figure 43. Slowly increase pressure to distribute the oil through the pump. Turn Prime/Spray Knob from prime A to ...

  • Wagner SprayTech 505 - page 23

    23 MAINTENANCE 4. Thoroughly clean the valve assembly with solvent and brush. 5. A properly seated valve filled with water and held vertically will not drip out the bottom of the valve. If you have properly cleaned the valve and water drips out the bottom, the valve is worn and needs to be replaced. 6. Install cleaned or new valve in the pump block ...

  • Wagner SprayTech 505 - page 24

    24 MAINTENANCE 2. If possible, leave the copper washer under the cap in place. At least be sure to replace it with the same side up. (The top will show the imprint of the end cap, while the bottom should be perfectly flat to match seat in the pump casting.) See Paint Pump Assem- bly Parts Diagram,Item 4 for replacement part num- ber. 3. With a wire ...

  • Wagner SprayTech 505 - page 25

    25 OPTIONAL HOPPER ASSEMBL Y CONVERTING SPRA YER FOR HOPPER OPERA TION Hopper Return Tube Hopper Figure 49 - Optional Hopper 4. Screw in the plastic return tube fitting into the paint pump port that the brass fitting was removed from. Attach hopper return tube to the fitting where the suction set return tube was removed. The connec- tion needs to b ...

  • Wagner SprayTech 505 - page 26

    26 Problem Cause Remedy Sprayer does not start up. Sprayer not plugged in. Plug in. ON/OFF switch OFF. Flip switch to ON. Blown fuse in circuit. Replace fuse. No voltage or low voltage Test power supply voltage. at wall plug. Unit turned off under pressure. Turn Prime/Spray Knob to Prime position. Damaged motor cord or Replace extension cord. exten ...

  • Wagner SprayTech 505 - page 27

    27 Problem Cause Remedy Spray gun won't shut off. Worn ball or seat. Take to Authorized Wagner Service Center. Foreign matter or paint Take to Authorized Wagner Service Center. buildup or dried paint between ball and seat. (Caused by improper cleaning of gun. Spray gun leaks. Worn or dirty internal parts. Take to Authorized Wagner Service Cent ...

  • Wagner SprayTech 505 - page 28

    28 ITEM PART NO. DESCRIPTION QTY. Parts Diagram – Final Assembly 1 0288478 Grip, Handle 1 2 0270357 Handle, Cart 1 3 9821503 Washer, Lock 4 4 9810111 Nut, Wing 2 5 0270356 Cart Assembly 1 6 0270359 Wheel 2 ITEM PART NO. DESCRIPTION QTY. 1 2 3 4 5 6 7 4 3 8 9 10 11 9 7 0275728 Cap, Hub 2 8 0270358 Bracket, Pail 1 9 9800117 Bolt, 1/4-20 x 1-1/2 3 1 ...

  • Wagner SprayTech 505 - page 29

    29 ITEM PART NO. DESCRIPTION QTY. ITEM PART NO. DESCRIPTION QTY. 1 0281113 Valve, Inlet Assembly 1 (includes item 12) 2 0089564 Cap, Outlet Assembly 1 3 9970103 Washer, Sealing, Copper 2 4 0047485 Spring, Outlet 1 5 0093635 Ball, 6mm, Carbide 1 6 0090348 Seat, Ball, Outlet Assembly 1 Parts Diagram – Paint Pump Assembly 1 2 7 6 5 4 3 8 3 10 11 12 ...

  • Wagner SprayTech 505 - page 30

    30 1 2 3 9 12 11 10 ITEM PART NO. DESCRIPTION QTY. ITEM PART NO. DESCRIPTION QTY. 7 0270371 Housing, Filter 1 8 0270369 Filter 1 9 0090621 Washer 1 10 0088715 Fitting, Return Hose 1 11 0089096 Clamp 1 12 0270363 Tubing, Return 1 1 0270133 Suction Tube Complete 1 (Includes Items 2 thru 10) 2 0090622 Nut, Suction 1 3 0281314 Elbow, Adapter, 3/4" ...

  • Wagner SprayTech 505 - page 31

    31 1 7 3 4 5 6 Accessories Part Description Number 0153000 Hose, 25' x 3/16", Grounded 0153001 Hose, 50' x 3/16', Grounded 0093896 Hose Connector 0149018 G-09 Spray Gun 0149017 G-10 Spray Gun 0089731 Gun Filter Assembly 0154675 Gun Filters, Medium/Fine 0093820 Adjustable Tip Part Description Number 0154681 Reversible Tip (light) ...

  • Wagner SprayTech 505 - page 32

    32 Parts and Accessories P ARTS LIST Item Part No. Description 1 0293004 G-06 Gun Assembly 2 0089731 Filter Assembly (Includes Items 3,4,5,6) 3 0043590 Spring 4 0089694 Seal, Nylon 5 0089692 Housing Filter 6 0089959 Filter Item Part No. Description 3 4 5 2 6 1 9 10 7 8 7 0293303 Guide, Hose 8 0154782 Tip, .011 (Oil based materials) 0154783 Tip, .01 ...

  • Wagner SprayTech 505 - page 33

    33 R Wagner Spray Tech Corporation 1770 Fernbrook Lane Minneapolis, Minnesota 55447 Telephone (612) 553-7000 LIMITED W ARRANTY AIRLESS P AINT SPRA Y EQUIPMENT This product, manufactured by Wagner Spray Tech Corporation (Wagner), is warranted to the original retail purchaser against defects in material and workmanship for 30 days from date of purcha ...

Fabbricante Wagner SprayTech Categoria Paint Sprayer

I documenti che otteniamo dal fabbricante del dispositivoWagner SprayTech 505 possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Wagner SprayTech
- manuali per l’uso 505
- schede prodotto Wagner SprayTech
- opuscoli
- o etichette energetiche Wagner SprayTech 505
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Wagner SprayTech 505.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Wagner SprayTech 505, manuali di manutenzione, brevi manuali o manuali utente Wagner SprayTech 505. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Wagner SprayTech 505.

Manuali per l’uso simili

Manuale completo del dispositivo Wagner SprayTech 505, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Wagner SprayTech 505 dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Wagner SprayTech 505.

Il manuale per l’uso completo Wagner SprayTech, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Wagner SprayTech 505 - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Wagner SprayTech 505, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Wagner SprayTech 505 che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Wagner SprayTech 505 - che ci dovrebbe aiutare nei primi passi durante l'uso Wagner SprayTech 505
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Wagner SprayTech 505
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Wagner SprayTech 505 in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Wagner SprayTech 505?

Utilizza il modulo sottostante

Se non hai risolto il problema con Wagner SprayTech 505 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Wagner SprayTech 505 è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)