Italiano dropdown-ico

Manuale per l’uso Stoelting 4231H

43 pagine 1.27 mb
Scarica

Vai alla pagina of 43

Summary
  • Stoelting 4231H - page 1

    Model 4231G/H OWNER'S MANUAL Manual No. 513534 Apr . 2003, Rev . 3 ...

  • Stoelting 4231H - page 2

    ...

  • Stoelting 4231H - page 3

    Need Part s or Service? We stock the parts you need.  Our Technicians are factory trained and are certified in the Stoelting Technicare program. Model No.: _______________________ Serial No.: _______________________ Purchase Date: ____________________ Start-Up Date:____________________ CALL Distributor: _________________________ Phone No.: _____ ...

  • Stoelting 4231H - page 4

    ...

  • Stoelting 4231H - page 5

    STOELTING OWNER'S MANUAL FOR MODEL 4231G STOELTING FLOOR GRAVITY FREEZER SOFT-SERVE This manual provides basic information about the freezer. Instructions and suggestions are given covering its operation and care. The illustrations and specifications are not binding in detail. We reserve the right to make changes at any time without notice to ...

  • Stoelting 4231H - page 6

    ...

  • Stoelting 4231H - page 7

    T ABLE OF CONTENTS Section Description Page 1 INTRODUCTION ................................................................................................. 1 1.1 Description ........................................................................................................... 1 1.2 Specifications .............................................. ...

  • Stoelting 4231H - page 8

    LIST OF ILLUSTRA TIONS Figure Description Page 1 Model 4231G Freezer ....................................................................................................... 1 2 Specifications ................................................................................................................ .... 1 3 Warning and Label Locations ........ ...

  • Stoelting 4231H - page 9

    1 1.1 DESCRIPTION The Stoelting® 4231G freezer is gravity fed. The freezer is equipped with fully automatic controls to provide a uniform product. The freezer is designed to operate with almost any type of commercial soft serve or non- dairy mixes available, including ice milk, ice cream, yogurt, and frozen dietary desserts. This manual is designe ...

  • Stoelting 4231H - page 10

    2 1.2 SPECIFICATIONS MODEL 4231G FLOOR MODEL GRAVITY FREEZER DIMENSIONS Freezer: 25.90” (65.81 cm) wide x 30.20” (76.7 cm) deep x 60.80” (154.4 cm) high Crated: 38.00” (96.5 cm) wide x 64.00” (162.5 cm) deep x 70.00” (178.0 cm) high WEIGHT Freezer: 640 lbs. (291 kg) Crated: 815 lbs. (370 kg) ELECTRICAL Refer to the nameplate located on ...

  • Stoelting 4231H - page 11

    3 2.1 SAFETY PRECAUTIONS SECTION 2 INST ALLA TION INSTRUCTIONS Figure 3. Warning Label Locations Do not attempt to operate the freezer until the safety precautions and operating instructions in this manual are read completely and are thoroughly understood. Take notice of all warning labels on the freezer (Fig. 3). The labels have been put there to ...

  • Stoelting 4231H - page 12

    4 2.2 SHIPMENT AND TRANSIT The freezer has been assembled, operated and inspected at the factory. Upon arrival at the final destination, the freezer must be checked for any damage that may have occurred during transit. With the method of packaging used, the freezer should arrive in excellent condition. THE CARRIER IS RESPONSIBLE FOR ALL DAMAGE IN T ...

  • Stoelting 4231H - page 13

    5 C . Accurate leveling is necessary for correct drainage of freezer barrel to insure correct over-run and flow . Place a spirit level on top of the freezer at each corner to check for level condition (Fig. 5). If adjustment is necessary , level the freezer by turning the casters in or out (Fig. 6). Figure 6. Caster Adjustment Figure 7. Connecting ...

  • Stoelting 4231H - page 14

    6 ...

  • Stoelting 4231H - page 15

    7 SECTION 3 INITIAL SET -UP AND OPERA TION 3.1 OPERATOR’S SAFETY PRECAUTIONS SAFE OPERATION IS NO ACCIDENT; Observe these rules: A. Know the freezer . Read and understand the Operating Instructions. B. Notice all warning labels on the freezer . C. W ear proper clothing. Avoid loose fitting garment s, and remove watches, rings or jewelry , which c ...

  • Stoelting 4231H - page 16

    8 A. SPIGOT SWITCH When the spigot handle is opened the SPIGOT switch will start the auger drive motor and refrigeration systems. When the spigot handle is closed, the auger drive motor and compressor will remain on until the product in the barrel reaches the proper consistency . B. CLEAN-OFF-SERVE SWITCH The CLEAN-OFF-SERVE switch is a three-posit ...

  • Stoelting 4231H - page 17

    9 3.3 SANITIZING Sanitizing must be done after the freezer is clean and just before the hopper is filled with mix. Sanitizing the night before is not effective. However, you should always clean the freezer and parts after using it. W ARNING THE UNITED ST A TES DEP ARTMENT OF AGRICUL TURE AND THE FOOD AND DRUG ADMINISTRA TION REQUIRE THA T ALL CLEAN ...

  • Stoelting 4231H - page 18

    10 E. After five minutes, place the bucket under the spigots and open all three spigots to drain the sanitizing solution. When the solution has drained, place the CLEAN-OFF-SERVE switch in the OFF position. Allow the freezer barrel to drain completely (Fig. 14). Figure 14. Spigot Opened and Solution Draining 3.4 FREEZE DOWN AND OPERATION This secti ...

  • Stoelting 4231H - page 19

    11 I. The freezer is designed to dispense the product at a reasonable draw rate. If the freezer is overdrawn, the result is a soft product or a product the will not dispense at all. If this should occur , allow the freezer to run for approximately 30 seconds before dispensing additional product. After a while the operator will sense or feel the fre ...

  • Stoelting 4231H - page 20

    12 B . Place the CLEAN-OFF-SERVE rocker switch in the CLEAN position. Allow the mix to agitate in freezer barrel until the mix has become a liquid. C . Drain the liquid mix by opening the spigot. A bucket or container should be placed under the spigot to catch the liquid mix (Fig. 19). Figure 19. Draining Mix D . Place the CLEAN-OFF-SERVE switch in ...

  • Stoelting 4231H - page 21

    13 C . Remove rosette cap. Push the spigot body through the bottom of the front door and remove the spigot body (Fig. 22). Figure 21. Removing Front Door D . Remove the front auger supports and bearings (Fig. 23). Figure 22. Removing Spigot Figure 23. Removing Auger Supports E. Remove the auger assemblies from the freezer . Pull the augers out of t ...

  • Stoelting 4231H - page 22

    14 J . Remove drain trays. 3.9 CLEANING THE FREEZER PARTS Place all loose parts in a pan or container and take to the wash sink for cleaning. To clean freezer parts refer to the following steps: A. Place all p art s in warm mild detergent water and clean with brushes provided. Rinse all parts with clean hot water . CAUTION DO NOT DAMAGE P ARTS BY D ...

  • Stoelting 4231H - page 23

    15 CAUTION DO NOT PLACE THE MIX INLET REGULA T OR INT O THE HOPPER BEFORE INST ALLING THE AUGER. E. Install the two plastic flights onto rear of the auger and insert part way into freezer barrel. F . Install the remaining plastic flights, push the auger into the freezer barrel and rotate slowly until the auger engages the drive shaft. G. Install th ...

  • Stoelting 4231H - page 24

    16 NOTE Refer to Section 3.3 for sanitizing the assembled freezer before filling with mix. L. Install the drain trays (Fig. 30). CAUTION DRAIN TRA YS MUST BE IN PLACE BEFORE OPERA TING FREEZER TO PREVENT DAMAGE FROM POSSIBLE AUGER SEAL LEAKS. Figure 30. Drain Trays 3.12 ROUTINE CLEANING To remove spilled or dried mix for the freezer exterior, simpl ...

  • Stoelting 4231H - page 25

    17 SECTION 4 MAINTENANCE INSTRUCTIONS 4.1 PREVENTIVE MAINTENANCE It is recommended that a preventive maintenance schedule be followed to keep the freezer clean and operating properly. The following steps are suggested as a preventive maintenance guide. W ARNING NEVER A TTEMPT T O REP AIR OR PERFORM MAINTENANCE ON FREEZER UNTIL THE MAIN ELECTRICAL P ...

  • Stoelting 4231H - page 26

    18 C. MONTHL Y 1. Check drive belt for wear . 2. Check condenser for dirt. 4.2 FREEZE-UP If a freeze-up does occur, use the following steps to thaw the mix in the freezer barrel: CAUTION IF THE DRIVE BEL T SQUEALS WHEN THE CLEAN-OFF-SERVE SWITCH IS PLACED IN THE SERVE POSITION, OR WHEN THE SPIGOT IS OPENED TO DISPENSE PRODUCT , TURN THE CLEAN-OFF-S ...

  • Stoelting 4231H - page 27

    19 4.5 TROUBLESHOOTING W ARNING NEVER A TTEMPT TO REP AIR OR PERFORM MAINTENANCE ON FREEZER UNTIL THE MAIN ELECTRICAL POWER HAS BEEN DISCONNECTED. Problem Possible Cause Remedy Freezer does not run 1. Power to freezer is off. 1. Supply power to freezer 2. Fuse or circuit breaker is blown or tripped. 2. Replace or reset. (If condition continues See ...

  • Stoelting 4231H - page 28

    20 Low overrun 1. Mix inlet regulator (carburetor) missing. 1. Replace mix inlet regulator (carburetor). 2. Mix inlet regulator (carburetor) “O” Ring 2. Replace mix inlet regulator missing. (carburetor) “O” Ring. 3. Mix inlet regulator (carburetor) air tube 3. Clean with sanitizer brush. blocked. Front door leaks. 1. Front door knobs are lo ...

  • Stoelting 4231H - page 29

    21 SECTION 5 REPLACEMENT P ARTS 5.1 HOW TO ORDER PARTS To assure receipt of the proper replacement parts, supply your dealer or distributor with the following information: A . Model number of equipment. B . Serial number of model, stamped on nameplate. Part Number Description 324014 Decal Black Arrow 324141 Decal Caution Rotating Blades 324509 D e ...

  • Stoelting 4231H - page 30

    22 ...

  • Stoelting 4231H - page 31

    23 Item Stoelting PN Qty Description 1 2177428 1 Door w/pins 2 3159696 2 Spigot, Outside 3 3158086 1 Spigot, Center 4 624598 4 O-Ring, 7/8 OD x 1/8 CS 5 624664 1 O-Ring 1-5/16 OD x 1-1/16 ID x 1/8 CS 6 625133 2 O- Ring 4.00" OD x .1875" CS 7 508135 As Reqd Lube, Petro-Gel 8 482019 4 Knob with 3/8-16 (Black) 9 624614 2 O-Ring, 1 OD x ¾ ID ...

  • Stoelting 4231H - page 32

    24 ...

  • Stoelting 4231H - page 33

    25 ...

  • Stoelting 4231H - page 34

    26 ...

  • Stoelting 4231H - page 35

    27 Item Stoelting PN Qty Description 1 152294 4 Belt V, 39.2 O.L. x 38.3 P.L. 2 282021-SV 2 Compressor (4231-18G, -38G) 2A 282020-SV 2 Compressor (4231-109G, -309G) 2B 282030 2 Compressor (4231-102G, -302G) 3 422156 2 Grommet Kit with sleeves 4 644371 8 Screw Cap 5/16-18 x 1-3/4 Hx 5 767211 8 Washer Flat 5/16, 7/8 x 3/8 x 14GA 6 522844 2 Motor, 2HP ...

  • Stoelting 4231H - page 36

    28 ...

  • Stoelting 4231H - page 37

    29 Item Stoelting PN Qty Description 1 649109 4 Screw Tap 10-16 x 1/2 Ind. Hx 2 524091 2 Mount Adhesive Back 1 x 1 Plastic 3 647885 2 Screw Mach 1/4-20 x 1/2 Trs Hd 4 538922 2 Nut Speed 1/4-20 5 766964 6 Washer Shakeproof 1/4 Zinc 6 644195 4 Screw Cap 1/4-20 x 2 Hx Hd 7 1172773 4 Spacer, 1.47 Long 8 2158124-SV 1 Door Interlock Switch Assy 9 766949 ...

  • Stoelting 4231H - page 38

    30 12, 13, 14 7 8 10 11 8 10 11 4A 4A 6 1, 2A, 2B 16 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 . . . . . 1 1 1 1 1 . . . . . . . . . . , , , , , 3 3 3 3 3 0 0 0 0 0 0 0 0 0 0 2 2 2 2 2 12, 13, 14 12, 13, 14 12, 13, 14 3 15 9 9 6 1, 2A, 2B 15 3 16 7 7 7 7 7 7 7 7 7 7 7 , , , , , 7 7 7 7 7 . . . . . / / / / / 5 5 5 5 5 0 0 0 0 0 , , ...

  • Stoelting 4231H - page 39

    31 Item Stoelting PN Qty Description 1 282021-SV 2 Compressor (4231-18G, -38G) 2A 282020-SV 2 Compressor (4231-109G, -309G) 2B 282030 2 Compressor (4231-102G, -302G) 3 4172774 1 Hopper & Evaporator Assembly 4 284104 2 Condenser (W/C Only) 4A 284044 1 Condenser (A/C Only) 5 718686 2 Swit ch Pressure (W/C Only) 6 342008 2 Drier, Filter 7 762277 2 ...

  • Stoelting 4231H - page 40

    32 12, 13, 14 7 8 10 11 8 10 11 4 4 6 1, 2A, 2B 16 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 . . . . . 1 1 1 1 1 . . . . . , , , , , 3 3 3 3 3 0 0 0 0 0 0 0 0 0 0 2 2 2 2 2 12, 13, 14 12, 13, 14 12, 13, 14 3 15 9 9 6 1, 2A, 2B 15 3 16 7 7 7 7 7 7 7 7 7 7 7 , , , , , 7 7 7 7 7 . . . . . / / / / / 5 5 5 5 5 . . . . . , , , , , 2 2 2 ...

  • Stoelting 4231H - page 41

    33 Item Stoelting PN Qty Description 1 282021-SV 2 Compressor (4231-18G, -38G) 2A 282020-SV 2 Compressor (4231-109G, -309G) 2B 282030 2 Compressor (4231-102G, -302G) 3 4172774 1 Hopper & Evaporator Assembly 4 284104 2 Condenser (W/C Only) 4A 284044 1 Condenser (A/C Only) 5 718686 2 Switch Pressure (W/C Only) 6 342008 2 Drier, Filter 7 762277 2 ...

  • Stoelting 4231H - page 42

    ...

  • Stoelting 4231H - page 43

    W ARRANTY SOFT SER VE / SHAKE FREEZERS 1. Scope: Stoelting, LLC warrants to the first user (the “Buyer”) that the freezer cylinders, hoppers, compressors, drive motors, speed reducers, auger and auger flights of Stoelting soft serve / shake freezers will be free from defects in materials and workmanship under normal use and proper maintenance a ...

Fabbricante Stoelting Categoria Freezer

I documenti che otteniamo dal fabbricante del dispositivoStoelting 4231H possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Stoelting
- manuali per l’uso 4231H
- schede prodotto Stoelting
- opuscoli
- o etichette energetiche Stoelting 4231H
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Stoelting 4231H.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Stoelting 4231H, manuali di manutenzione, brevi manuali o manuali utente Stoelting 4231H. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Stoelting 4231H.

Manuali per l’uso simili

Manuale completo del dispositivo Stoelting 4231H, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Stoelting 4231H dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Stoelting 4231H.

Il manuale per l’uso completo Stoelting, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Stoelting 4231H - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Stoelting 4231H, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Stoelting 4231H che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Stoelting 4231H - che ci dovrebbe aiutare nei primi passi durante l'uso Stoelting 4231H
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Stoelting 4231H
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Stoelting 4231H in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Stoelting 4231H?

Utilizza il modulo sottostante

Se non hai risolto il problema con Stoelting 4231H con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Stoelting 4231H è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)