Italiano dropdown-ico

Manuale per l’uso Andrew ATC200-Lite

66 pagine 1.79 mb
Scarica

Vai alla pagina of 66

Summary
  • Andrew ATC200-Lite - page 1

    Andrew Corporation Base Station Antennas 2601 T elecom Parkway Richardson, T exas 75082-3521 T el: (214) 631-0310 Fax: (214) 631-4706 www .andrew .com A TC200-Lite T eletilt ® Remote Control V ariable Electrical Downtilt System Installation and Operation User Guide Bulletin 639510 • May 2005 ...

  • Andrew ATC200-Lite - page 2

    Do not install near power lines. Power lines, telephone lines, and guy wires look the same. Assume any wire or line can Do no t insta ll on a w et or wi ndy day or whe n lightning or thunder is in the area. Do not use metal ladder . Wear shoes with rubber soles and heels. Wear protective clothing including a long- sleeved shirt and rubber gloves. N ...

  • Andrew ATC200-Lite - page 3

    Bulletin 639510 May 2005 i Revision History Revision No. Date Description of Changes None May 2005 Released. ...

  • Andrew ATC200-Lite - page 4

    A TC200-Lite T eletilt ® Remote Control Downtilt System ii May 2005 Bulletin 639510 ...

  • Andrew ATC200-Lite - page 5

    A TC200-Lite T eletilt ® Remote Control Downtilt System Bulletin 639510 May 2005 iii ...

  • Andrew ATC200-Lite - page 6

    A TC200-Lite T eletilt ® Remote Control Downtilt System iv May 2005 Bulletin 639510 Electric Static Discharge (ESD) can damage or destroy the hardware equipment used for the A TC200-Lite T eletilt ® System. ESD can occur dur- ing handling of equipment without the user feeling a sh ock. The fo llowi ng pr ecau tions shou ld be taken to prevent ESD ...

  • Andrew ATC200-Lite - page 7

    A TC200-Lite T eletilt ® Remote Control Downtilt System Bulletin 639510 May 2005 v 5. Always avoid unnecessary movement of body , such as scufng feet across ooring, when handling ESDS equipment. Such movement will generate additional charges of static electricity . 6. When removing or replacing ESDS ...

  • Andrew ATC200-Lite - page 8

    A TC200-Lite T eletilt ® Remote Control Downtilt System vi May 2005 Bulletin 639510 This page intentionally left blank. ...

  • Andrew ATC200-Lite - page 9

    Bulletin 639510 May 2005 v T able of Contents Revision History .................................................................................................... i Letter of Compliance............................................................................................. ii Declaration of Conformity ......................................... ...

  • Andrew ATC200-Lite - page 10

    T able of Contents A TC200-Lite T eletilt ® Remote Control Downtilt System ii May 2005 Bulletin 639510 vi May 2005 Section 9 Device T est, Alarm Status and Device Information ........................... 9-1 9.1 Obtaining Device Information ..................................................................................... 9-2 9.2 Retrieving Curr ...

  • Andrew ATC200-Lite - page 11

    Bulletin 639510 May 2005 1-1 Section 1 Controller Setup 1.1 System Description The A TC200-Lite series control system consists of an antenna system controller , actuators attached to the antennas (one for each variable tilt adjuster on an antenna), junction boxes/ splitters to daisy chain up to 32 actuators to a controller , and control cable assem ...

  • Andrew ATC200-Lite - page 12

    Section 1–Controller Setup A TC200-Lite T eletilt ® Remote Control Downtilt System 1-2 May 2005 Bulletin 639510 Figure 1-1. ATC200-Lite Controller with RS-232 Serial Cable Attached. 2. Connect the supplied 24Vdc or 12Vdc power converter to the dc IN port on the controller (Figu re 1-1). IMPORT ANT NOTE: The power conver ter used will affect both ...

  • Andrew ATC200-Lite - page 13

    A TC200-Lite T eletilt ® Remote Control Downtilt System Section 1–Controller Setup Bulletin 639510 May 2005 1-3 Power dc Not Supplied Local Control Interface Junction Box A TJB200-A01-007 Cable Assembly A TCB-B01-006 Field Installed Actuator A TM200-001 Cable Assembly A TCB-B01-060 Cable Assembly A TCB-B01-002 Ethernet (10 Base T) Equipment Cabi ...

  • Andrew ATC200-Lite - page 14

    Section 1–Controller Setup A TC200-Lite T eletilt ® Remote Control Downtilt System 1-4 May 2005 Bulletin 639510 This page intentionally left blank. ...

  • Andrew ATC200-Lite - page 15

    Bulletin 639510 May 2005 2-1 Section 2 Program Installation 2.1 Program Download and Installation 1. Downloadtheziplecontainingthe A TC200-Litesetuplefromthe AndrewCorpora - tionwebsite(www .andrew .com).ThisziplecanbeplacedinanydirectoryonthePC’ s loc ...

  • Andrew ATC200-Lite - page 16

    Section 2–Program Installation A TC200-Lite T eletilt ® Remote Control Downtilt System 2-2 May 2005 Bulletin 639510 Figure 2-3. Setup Introduction Screen. Figure 2-4. Installation Settings Screen. ...

  • Andrew ATC200-Lite - page 17

    A TC200-Lite T eletilt ® Remote Control Downtilt System Section 2–Program Installation Bulletin 639510 May 2005 2-3 Figure 2-5. Completing Setup Screen. 2.2 Software Upgrades and Antenna Definition F ile Updates Softwareupgrades containing updatedantenna denitionles willbe availableto download fromAnd ...

  • Andrew ATC200-Lite - page 18

    Section 2–Program Installation A TC200-Lite T eletilt ® Remote Control Downtilt System 2-4 May 2005 Bulletin 639510 Thispageintentionallyleftblank. ...

  • Andrew ATC200-Lite - page 19

    Bulletin 639510 May 2005 3-1 Section 3 Program Startup and Configuration 3.1 Preparing for Program Startup This program is designed to congure and control Andrew’s A TC200-Lite T eletilt ® , AISG1 compliant, RET antenna system through a controller connected to a local PC. 1. V erify that the A TC200-Lite controller is turned off/powered down, ...

  • Andrew ATC200-Lite - page 20

    Section 3–Program Startup and Conguration A TC200-Lite T eletilt ® Remote Control Downtilt System 3-2 May 2005 Bulletin 639510 Figure 3-3. ATC200-Lite Main Screen. 3.2 Serial P ort Selection at Program Startup 1. The install process places an icon for the program on the desktop (Figure 3-2). Figure 3-4. Prompt for Serial Port Selection. Figur ...

  • Andrew ATC200-Lite - page 21

    A TC200-Lite T eletilt ® Remote Control Downtilt System Section 3–Program Startup and Conguration Bulletin 639510 May 2005 3-3 Figure 3-5. Selecting a Serial Port. Figure 3-6. Prompt to Select a Different Port. 4. If this occurs, use the ‘Communication’ menu located at the top of the main screen to select an available serial port. Make ce ...

  • Andrew ATC200-Lite - page 22

    Section 3–Program Startup and Conguration A TC200-Lite T eletilt ® Remote Control Downtilt System 3-4 May 2005 Bulletin 639510 3.3 Beginning Program Operation After program startup and serial port selection, note the text displayed at the bottom of the screen in the ‘Command Status/Response’ window (Figure 3-3). This window is used to dis ...

  • Andrew ATC200-Lite - page 23

    A TC200-Lite T eletilt ® Remote Control Downtilt System Section 3–Program Startup and Conguration Bulletin 639510 May 2005 3-5 Figure 3-8. Selecting ‘Antenna Files’ from Main Menu . Go to ‘Tools, A ntenna Files’ to uplo ad antenna d efinition files . This feature can be used to upload newer versions of antenna de finition files. This ...

  • Andrew ATC200-Lite - page 24

    Section 3–Program Startup and Conguration A TC200-Lite T eletilt ® Remote Control Downtilt System 3-6 May 2005 Bulletin 639510 This page intentionally left blank. ...

  • Andrew ATC200-Lite - page 25

    Bulletin 639510 May 2005 4-1 Section 4 Device Discovery and A ddressing 4.1 Device Search After an antenna denition le has been loaded, automatically during program installation or manually by the user (see Section 3), a device search can be activated. A device search is the process by which the program performs an AISG compliant device scan ...

  • Andrew ATC200-Lite - page 26

    Section 4–Device Discovery and Addressing A TC200-Lite T eletilt ® Remote Control Downtilt System 4-2 May 2005 Bulletin 639510 2. The ‘Auto Discovery’ bar (located at the top of the screen) and the Command Status/Re - sponse window (located at the bottom of the screen) will show the status on the search’s progress (Figure 4-2). As each dev ...

  • Andrew ATC200-Lite - page 27

    A TC200-Lite T eletilt ® Remote Control Downtilt System Section 4–Device Discovery and Addressing Bulletin 639510 May 2005 4-3 3. At complet ion of the search, a noticat ion will appear showing the number of devices found (Figure 4-3). NOTE: If it is known that devices are present and operational, but none were found by the device search, it ...

  • Andrew ATC200-Lite - page 28

    Section 4–Device Discovery and Addressing A TC200-Lite T eletilt ® Remote Control Downtilt System 4-4 May 2005 Bulletin 639510 4.2 A ddressing 1. If desired, these devices can be manually readdressed by the user . It is important to note that if manual addressing is performed, the ‘Find Device’ search function will automatically clear all ma ...

  • Andrew ATC200-Lite - page 29

    A TC200-Lite T eletilt ® Remote Control Downtilt System Section 4–Device Discovery and Addressing Bulletin 639510 May 2005 4-5 3. A message will appear that the device was successfully removed from the address it originally held. Click ‘OK’ to return to the ‘Manual Addressing’ screen (Figure 4-7). 4. T o assign a specic address that i ...

  • Andrew ATC200-Lite - page 30

    Section 4–Device Discovery and Addressing A TC200-Lite T eletilt ® Remote Control Downtilt System 4-6 May 2005 Bulletin 639510 6. The ‘Manual Addressing’ screen will automatically suggest the rst avail - able address. The default serial num - ber for a device with an unassigned address is a series of zeros. If the suggested address is acc ...

  • Andrew ATC200-Lite - page 31

    A TC200-Lite T eletilt ® Remote Control Downtilt System Section 4–Device Discovery and Addressing Bulletin 639510 May 2005 4-7 Click ‘Close’. Figure 4-13. Closing ‘Manual Addressing’ Screen. 9. Click ‘Close’ (Figure 4-13). 10. T he de vic e will disp lay it s new add re ss in the ‘Device Information’ list on the main screen (Figu ...

  • Andrew ATC200-Lite - page 32

    Section 4–Device Discovery and Addressing A TC200-Lite T eletilt ® Remote Control Downtilt System 4-8 May 2005 Bulletin 639510 This page intentionally left blank. ...

  • Andrew ATC200-Lite - page 33

    Bulletin 639510 May 2005 5-1 Section 5 Device Configuration After new devices are found and addressed in the A TC200-Lite program, each device is ready to be congured. New devices, that have never been congured before, will display the status as ‘Not Congured’ in the ‘Device Information’ list. 1. T o begin device conguration, cl ...

  • Andrew ATC200-Lite - page 34

    Section 5–Device Conguration A TC200-Lite T eletilt ® Remote Control Downtilt System 5-2 May 2005 Bulletin 639510 Note the following in Figure 5-2: • The ID of the device to be congured is displayed in the title bar of the dialog box. • Devices that have never been congured before will display blank elds for all param - eters, wi ...

  • Andrew ATC200-Lite - page 35

    A TC200-Lite T eletilt ® Remote Control Downtilt System Section 5–Device Conguration Bulletin 639510 May 2005 5-3 3. Click on the down arrow found on the right hand side of the ‘Antenna Model‘ drop down list. This will display all of the available Andrew base station antenna models that were contained in the antenna denition le that ...

  • Andrew ATC200-Lite - page 36

    Section 5–Device Conguration A TC200-Lite T eletilt ® Remote Control Downtilt System 5-4 May 2005 Bulletin 639510 Alternately , the suggested date may be erased and a new date entered, or the eld may be left blank. When a date is entered, it must be formatted as shown in Figure 5-2 (A ‘forward slash’ character placed between the month ...

  • Andrew ATC200-Lite - page 37

    A TC200-Lite T eletilt ® Remote Control Downtilt System Section 5–Device Conguration Bulletin 639510 May 2005 5-5 If this occurs, ensure that all cables and connec tors to the actuat or are properly connect ed, and that the system is still properly powered up. Also, verify that the actuator is present in the ‘Device Information’ list, and ...

  • Andrew ATC200-Lite - page 38

    Section 5–Device Conguration A TC200-Lite T eletilt ® Remote Control Downtilt System 5-6 May 2005 Bulletin 639510 This page intentionally left blank. ...

  • Andrew ATC200-Lite - page 39

    Bulletin 639510 May 2005 6-1 Section 6 Changing the Electrical Downtilt on a Single Antenna The electrical downtilt may be adjusted on any device that is addressed, congured, and whose current state does not prevent antenna movement. Examples where movement is prevented include devices that are not responding to commands from the program, device ...

  • Andrew ATC200-Lite - page 40

    Section 6–Changing the Electrical Downtilt-Single A TC200-Lite T eletilt ® Remote Control Downtilt System 6-2 May 2005 Bulletin 639510 3. The ‘Set Antenna T ilt’ screen will appear (Figure 6-2). Note, all parameters that can be congured are displayed on this screen. This information may be used as a reference to help determine the new til ...

  • Andrew ATC200-Lite - page 41

    A TC200-Lite T eletilt ® Remote Control Downtilt System Section 6–Changing the Electrical Downtilt-Single Bulletin 639510 May 2005 6-3 5. Click the ‘Activate’ button (Figure 6-2) to apply changes to the electrical downtilt for this antenna. Alternately , to exit the screen without sending any changes, click on the ‘Close’ button. Antenna ...

  • Andrew ATC200-Lite - page 42

    Section 6–Changing the Electrical Downtilt-Single A TC200-Lite T eletilt ® Remote Control Downtilt System 6-4 May 2005 Bulletin 639510 7. At the successful completion of an antenna movement, the ‘Current T ilt’ eld will update to show the new tilt angle and the ‘New T ilt’ text entry box will be cleared in preparation for the next mov ...

  • Andrew ATC200-Lite - page 43

    Bulletin 639510 May 2005 7-1 Section 7 Changing the Electrical Downtilt on a Group of Antennas In addition to changing the downtilt of a single antenna, changes may also be applied to a gro up of anten nas. The list of ante nnas that mak e up the grou p is de ned by three con gur atio n parameters – Sector ID, Minimum Electrical T ilt, and ...

  • Andrew ATC200-Lite - page 44

    Section 7–Changing the Electrical Downtilt-Group A TC200-Lite T eletilt ® Remote Control Downtilt System 7-2 May 2005 Bulletin 639510 Other devices that have the same sector ID, minimum tilt, and maximum tilt are listed in the box labeled ‘Additional Compatible Antennas’. The devices in this box may be included in the move by moving one or m ...

  • Andrew ATC200-Lite - page 45

    A TC200-Lite T eletilt ® Remote Control Downtilt System Section 7–Changing the Electrical Downtilt-Group Bulletin 639510 May 2005 7-3 6. After the devices are moved to the ‘Antennas Included In Move’ box, examine the group to ensure that the group does not include any antennas that are not desired for this move. 7. T o remove one or more ant ...

  • Andrew ATC200-Lite - page 46

    Section 7–Changing the Electrical Downtilt-Group A TC200-Lite T eletilt ® Remote Control Downtilt System 7-4 May 2005 Bulletin 639510 9. Y ou will be notied when all antennas have successfully reached the new tilt angle. Click ‘OK’ (Figure 7-4). 10. Th e ‘ S e t E l e c t r i c a l Ti l t f o r S e c t o r ’ screen will display the ne ...

  • Andrew ATC200-Lite - page 47

    Bulletin 639510 May 2005 8-1 Section 8 Saving a Site Report or Site Configurations Site conguration information can be saved for future reference using either the ‘File, Save Site Report’ option or the ‘File, Save Site Conguration’ option from the main program menu. The ‘File, Save Site Report’ option allows site conguration in ...

  • Andrew ATC200-Lite - page 48

    Section 8–Saving Site Report/Congurations A TC200-Lite T eletilt ® Remote Control Downtilt System 8-2 May 2005 Bulletin 639510 Figure 8-2. Selecting the File Format for Word. 1. A ssign a filename to th e report. The date, ti me, and the SiteID o f the first configured a ctuator are use d for the sugge sted filename. 3. Click ‘Sav e’. Not ...

  • Andrew ATC200-Lite - page 49

    A TC200-Lite T eletilt ® Remote Control Downtilt System Section 8–Saving Site Report/Congurations Bulletin 639510 May 2005 8-3 2. Change file ty pe to ‘All F iles (*.*)’. This will allow the file sav ed as a repo rt for Word to be seen fo r selection . 3. Select the ‘ txtrpt’ file. . 1. Go to th e ‘ATC200_ Site_Files’ directory . ...

  • Andrew ATC200-Lite - page 50

    Section 8–Saving Site Report/Congurations A TC200-Lite T eletilt ® Remote Control Downtilt System 8-4 May 2005 Bulletin 639510 Figure 8-4. Report File Opened in Word. 6. The conguration settings for each actuator are displayed in the order of their address (Figure 8-4). ...

  • Andrew ATC200-Lite - page 51

    A TC200-Lite T eletilt ® Remote Control Downtilt System Section 8–Saving Site Report/Congurations Bulletin 639510 May 2005 8-5 8.2 Saving/V iewing a Site Report F ormatted to Open in Excel. 1. T o save a report that can be opened in Excel (or any other spreadsheet software program), go to ‘File, Save Site Report’ from the main menu (Figur ...

  • Andrew ATC200-Lite - page 52

    Section 8–Saving Site Report/Congurations A TC200-Lite T eletilt ® Remote Control Downtilt System 8-6 May 2005 Bulletin 639510 5. T o view the saved le, launch Excel (or a similar softwa re applicat ion) and go to ‘File , Open‘ from the main menu. Change the directory to look in ‘C:A TC200_Site_Files’, change the le type to ‘ ...

  • Andrew ATC200-Lite - page 53

    A TC200-Lite T eletilt ® Remote Control Downtilt System Section 8–Saving Site Report/Congurations Bulletin 639510 May 2005 8-7 6. The conguration settings for each actuator are displayed in the order of their address (Figure 8-7). Figure 8-7. Report File Opened in Excel. ...

  • Andrew ATC200-Lite - page 54

    Section 8–Saving Site Report/Congurations A TC200-Lite T eletilt ® Remote Control Downtilt System 8-8 May 2005 Bulletin 639510 8.3 Saving Configurations for F uture Use. Congurations can be saved to the hard drive for future use. At the time of this software re - lease (V ersion 2.1), the A TC200-Lite program is not able to open a saved co ...

  • Andrew ATC200-Lite - page 55

    Bulletin 639510 May 2005 9-1 Section 9 Device T est, Alarm Status and Device Information The A TC200-Lite program allows users to obtain device information (includes hardware and software version), get alarm status or clear alarms for any known device, or run a movement self-test on any addressed device. These options are displayed as four buttons ...

  • Andrew ATC200-Lite - page 56

    Section 9–Device T est, Alarm Status, Device Info. A TC200-Lite T eletilt ® Remote Control Downtilt System 9-2 May 2005 Bulletin 639510 Figure 9-2. Device Information Displayed. 9.1 Obtaining Device Information This option retrieves and displays the serial number for the device, the version for the controller hardware, and the version for the so ...

  • Andrew ATC200-Lite - page 57

    A TC200-Lite T eletilt ® Remote Control Downtilt System Section 9–Device T est, Alarm Status, Device Info. Bulletin 639510 May 2005 9-3 9.3 Clearing All Alarms on a Device After examining the alarms status results, any alarms found may be cleared using the ‘Clear Alarms’ button. 1. Click on the device in the ‘Device In - formation’ list ...

  • Andrew ATC200-Lite - page 58

    Section 9–Device T est, Alarm Status, Device Info. A TC200-Lite T eletilt ® Remote Control Downtilt System 9-4 May 2005 Bulletin 639510 1. T o perfor m a self test on a devic e, click on the device in the ‘Device Informa- tion’ list (Figure 9-1). 2. Click ‘Self T est’ to initiate movement (Figure 9-1). 3. At the com pletion o f th e s el ...

  • Andrew ATC200-Lite - page 59

    Bulletin 639510 May 2005 10-1 Section 10 P art Numbering Scheme and Ordering Guide P ART NUMBER DESCRIPTION A TC200-Lite-00xx Local controller system. The system includes: • local controller , model A TC200-Lite • Ethernet crossover cable • power cord* • Phoenix 48 V olt power connector • this installation and operation manual, part numbe ...

  • Andrew ATC200-Lite - page 60

    Section 10–Part Numbering Scheme & Ordering Guide A TC200-Lite T eletilt ® Remote Control Downtilt System 10-2 May 2005 Bulletin 639510 10.2 Ordering Guide As an example, assume a system is to be ordere d for deployment in North America. The site is a three sector site employing three UMWD-06516-XDM antennas. For this example, let’s say th ...

  • Andrew ATC200-Lite - page 61

    Bulletin 639510 May 2005 1 1-1 Section 11 Control System Specifications Electrical Number of Independent Antenna Drives: Up to 32 per controller DC Power Input (24VDC): 36w (max) AC Power Input (1 10/240V AC): .5A @ 120V AC Power to Actuators: 1.5A @ 24VDC Mechanical Size of Local Controller–mm (LxWxD): 100 x 70 x 34 Weight of Local Controller– ...

  • Andrew ATC200-Lite - page 62

    Section 1 1–Control System Specications A TC200-Lite T eletilt ® Remote Control Downtilt System 1 1-2 May 2005 Bulletin 639510 This page intentionally left blank. ...

  • Andrew ATC200-Lite - page 63

    ATC200-Lite Series TELETILT ® System Site Configuration Worksheet SITE I.D. Actuator Antenna Actuator Serial No. Sector/ Orientation Height Miscellaneous 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Bulletin 639510 ...

  • Andrew ATC200-Lite - page 64

    ATC200-Lite Series TELETILT ® System Site Configuration Worksheet SITE I.D. Actuator Antenna Actuator Serial No. Sector/ Orientation Height Miscellaneous 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 Bulletin 639510 ...

  • Andrew ATC200-Lite - page 65

    Bulletin 639510 May 2005 B-1 Appendix B Antennas F or A TC200-Lite Series System The following table is an example of antenna models compatible for use with the A TC200-Lite series T eletilt ® system. As new models become available for use with this system, updates will be made to the A TC200-Lite controller software. Registered user ’s are noti ...

  • Andrew ATC200-Lite - page 66

    Appendix B–Antenna Listing A TC200-Lite T eletilt ® Remote Control Downtilt System B-2 May 2005 Bulletin 639510 This page intentionally left blank. ...

Fabbricante Andrew Categoria Stereo System

I documenti che otteniamo dal fabbricante del dispositivoAndrew ATC200-Lite possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Andrew
- manuali per l’uso ATC200-Lite
- schede prodotto Andrew
- opuscoli
- o etichette energetiche Andrew ATC200-Lite
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Andrew ATC200-Lite.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Andrew ATC200-Lite, manuali di manutenzione, brevi manuali o manuali utente Andrew ATC200-Lite. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Andrew ATC200-Lite.

Manuali per l’uso simili

Manuale completo del dispositivo Andrew ATC200-Lite, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Andrew ATC200-Lite dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Andrew ATC200-Lite.

Il manuale per l’uso completo Andrew, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Andrew ATC200-Lite - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Andrew ATC200-Lite, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Andrew ATC200-Lite che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Andrew ATC200-Lite - che ci dovrebbe aiutare nei primi passi durante l'uso Andrew ATC200-Lite
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Andrew ATC200-Lite
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Andrew ATC200-Lite in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Andrew ATC200-Lite?

Utilizza il modulo sottostante

Se non hai risolto il problema con Andrew ATC200-Lite con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Andrew ATC200-Lite è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)