Italiano dropdown-ico

Manuale per l’uso Alto-Shaam 1020ESG

36 pagine 2.19 mb
Scarica

Vai alla pagina of 36

Summary
  • Alto-Shaam 1020ESG - page 1

    Combitherm ® Combination Ov en / Steamer E S GAS COM B IT OUCH ® S ERI ES 6•10 ES G 10•10 ES G 7•14 ES G 10•20 ES G 12•18 ES G 20•20 ES G • I N ST ALLA T I O N W164 N9221 W ater Street • P .O. Box 450 • Menomonee Falls, W isconsin 53052-0450 USA PHONE: 262.251.3800 • 800.558.8744 USA/CANADA F AX: 262.251.7067 • 800.329.8744 ...

  • Alto-Shaam 1020ESG - page 2

    i Delivery .......................................................................... 1 Unpacking ..................................................................... 1 Safety Procedur es and Precautions .............................. 2 Installation Installation Codes and Standards ............................. 3 V entilation Requirements ........ ...

  • Alto-Shaam 1020ESG - page 3

    COMBITOUCH ® ESG SERIES • GAS INST ALLA TION MANUAL • MN-29246 • 1. THE INFORMATION CONTAINED IN THIS MANUAL IS IMPORTANT FOR THE PROPER INSTALLATION OF THIS OVEN. PLEASE READ CAREFULLY AND RETAIN FOR FUTURE REFERENCE. IMPROPER CONNECTION OF THIS APPLIANCE WILL NULLIFY ALL WARRANTIES. LES INFORMATIONS CONTENUES DANS CE MANUEL SONT IMPORTANTE ...

  • Alto-Shaam 1020ESG - page 4

    COMBITOUCH ® ESG SERIES • GAS INST ALLA TION MANUAL • MN-29246 • 2. CAUTION Used to indicate the presence of a hazard that can or will cause minor personal injury, property damage, or a potential unsafe practice if the warning included with this symbol is ignored. CAUTION Used to indicate the presence of a hazard that can or will cause minor ...

  • Alto-Shaam 1020ESG - page 5

    COMBITOUCH ® ESG SERIES • GAS INST ALLA TION MANUAL • MN-29246 • 3. INSTALLATION SITE INSTALLATION INSTALLATION CODES & STANDARDS The following codes and standards ar e required for installation of this oven: AIR SUPPL Y , ELECTRICAL CONNECTIONS, W A TER CONNECTIONS, AND W ASTE W A TER DISCHARGE. Installation must comply with local codes ...

  • Alto-Shaam 1020ESG - page 6

    COMBITOUCH ® ESG SERIES • GAS INST ALLA TION MANUAL • MN-29246 • 4. INSTALLATION SITE INSTALLATION NOTE: Note dimensions required for doorways and aisles for access of the oven and pallet to the installation site. Transport the oven in an upright and level position only. Do not tilt the oven. ® POSITIONING ON SITE Stand the oven in a level ...

  • Alto-Shaam 1020ESG - page 7

    COMBITOUCH ® ESG SERIES • GAS INST ALLA TION MANUAL • MN-29246 • 5. INSTALLATION SITE INSTALLATION POSITIONING REQUIREMENTS q In order to ensure proper ventilation, a minimum distance of at least 6-inches (152mm) must be kept from the control panels side (left) of the oven and any adjoining surfaces. NOTE: Additional clearance is needed for ...

  • Alto-Shaam 1020ESG - page 8

    COMBITOUCH ® ESG SERIES • GAS INST ALLA TION MANUAL • MN-29246 • 6. SITE INSTALLATION Lifting Ins tructions Do not lift in this area! Damage t o the components will r esult. Cent er of Gra vity Front View T op View (Fron t) Leg 24” Spacer Board Remov e banding befor e lift ing. Place a spacer boar d(s ) 24” in length, with a minimum h ei ...

  • Alto-Shaam 1020ESG - page 9

    COMBITOUCH ® ESG SERIES • GAS INST ALLA TION MANUAL • MN-29246 • 7. INSTALLATION COMMON SPECIFICATIONS q CombiGuard™ BWS Blended W ater System FI-28727 (INCLUDES 50 GALLON T ANK, 1 MEMBRANE & 3 FIL TERS) q CombiGuard™ BWS Replacement Filter Cartridge AMS-QT FI-29316 q CombiGuard™ BWS Replacement Filter Cartridge SCLX2-Q FI-29317 q ...

  • Alto-Shaam 1020ESG - page 10

    COMBITOUCH ® ESG SERIES • GAS INST ALLA TION MANUAL • MN-29246 • 8. 6 • 10 ES G B C D 2-15/16" (74mm) 2" (50mm) 47-5/16" (1201mm) 42-1/16" (1068mm) 40-1/8" (1018mm) 37" (939mm) 34-5/16" (871mm) Wa ter Drain (Bottom) 21-1 1/16" (550mm) 5-3/16" (131mm) 25" (635mm) 7-1/2" (191mm) 7-9/16&q ...

  • Alto-Shaam 1020ESG - page 11

    COMBITOUCH ® ESG SERIES • GAS INST ALLA TION MANUAL • MN-29246 • 9. 10 • 10 ES G 21-11/16" (550mm) 5-3/16" (131mm) 42-1/16" (1068mm) 40-1/8" (1018mm) 37" (939mm) 34-5/16" (871mm) Water Drain (Bottom) 5" (125mm) 5-9/16" (140mm) 41-7/16" (1053mm) 33-7/8" (860mm) 46-3/8" (1178mm) 25" ...

  • Alto-Shaam 1020ESG - page 12

    COMBITOUCH ® ESG SERIES • GAS INST ALLA TION MANUAL • MN-29246 • 10. 7 • 14 ES G D A B Water Drain (Bottom) (650mm) 8-1/2" (216mm) 25-5/8" 42" (1066mm) 5-1/8" (130mm) 31-3/4" (805mm) 33-1/8" (840mm) 7-3/16" (181mm) 73-7/16" (1865mm) 36-7/16" (925mm) 30-3/ 16 " (766mm) [D] 4-5/8" (116mm ...

  • Alto-Shaam 1020ESG - page 13

    COMBITOUCH ® ESG SERIES • GAS INST ALLA TION MANUAL • MN-29246 • 11. 10 • 20 ES G 45-3/16" (1148mm) 42-7/16" (1077mm) 22-11/16" (575mm) 12-13/16" (325mm) Water Drain (Bottom) 2-3/16" (56mm) 30-5/8" (778mm) 32-13/16" (833mm) 44" (1118mm) 2" (50mm) 31-3/4" (805mm) 8-15/16" (226mm) 49-13/ ...

  • Alto-Shaam 1020ESG - page 14

    COMBITOUCH ® ESG SERIES • GAS INST ALLA TION MANUAL • MN-29246 • 12. 12 • 18 ES G 25-5/8" (650mm) 33-1/8" (840mm) 45-3/16" (1148mm) 42-7/16" (1077mm) 22-11/16" (575mm) 12-13/16" (325mm) Water Drain (Bottom) 8-1/2" (216mm) 31-3/4" (805mm) 52-11/16" (1338mm) 40-9/16" (1030mm) 48-1/8" (12 ...

  • Alto-Shaam 1020ESG - page 15

    COMBITOUCH ® ESG SERIES • GAS INST ALLA TION MANUAL • MN-29246 • 13. 20 • 20 ES G [A,B] 4-3/8" (110mm) [D] 4-9/16" (116mm) [C] 3-9/16" (89mm) Water Drain (Side Back) [D] 4-5/8" (116mm) 2" (50mm) 55-7/16" (1407mm) 73-13/16" (1875mm) 5-7/8" (148mm) 17-1/4" (438mm) 19-11/16" (500mm) 26-9/16&qu ...

  • Alto-Shaam 1020ESG - page 16

    COMBITOUCH ® ESG SERIES • GAS INST ALLA TION MANUAL • MN-29246 • 14. INSTALLATION ELECTRICAL An electrical wiring diagram is located behind the control panel on the left side of the oven. This appliance must be branch circuit pr otected with proper ampacities, in accordance with the wiring diagram. W ire size for the main incoming power to t ...

  • Alto-Shaam 1020ESG - page 17

    COMBITOUCH ® ESG SERIES • GAS INST ALLA TION MANUAL • MN-29246 • 15. INSTALLATION MOBILE EQUIPMENT RESTRAINT The gas Combitherm must use a connector that complies with The Standard for Connectors for Movable Gas Appliances , ANSI Z21.69 CSA 6.16 and addenda Z21.69a-1989. A quick disconnect devise must be installed to comply with The Standard ...

  • Alto-Shaam 1020ESG - page 18

    COMBITOUCH ® ESG SERIES • GAS INST ALLA TION MANUAL • MN-29246 • 16. INSTALLATION VENTILATION REQUIREMENTS An adequate ventilation system is requir ed for commercial cooking equipment. Information may be obtained by writing to the National Fire Pr otection Association, Batterymarch Park, Quincy , MA 02269. When writing refer to NFP A No. 96. ...

  • Alto-Shaam 1020ESG - page 19

    COMBITOUCH ® ESG SERIES • GAS INST ALLA TION MANUAL • MN-29246 • 17. INSTALLATION GAS SUPPLY & INSTALLATION The Alto-Shaam gas Combitherm has been set to operate with either natural gas or propane as indicated on the identification name plate. Make certain the gas supply matches the nameplate information. Should conversion to the opposit ...

  • Alto-Shaam 1020ESG - page 20

    COMBITOUCH ® ESG SERIES • GAS INST ALLA TION MANUAL • MN-29246 • 18. INSTALLATION GAS SUPPLY & INSTALLATION Remove any tape or compound residue on all external thread connections before proceeding. Use an approved gas pipe sealant at all external threaded connections, Gas piping used on gas connections must avoid sharp bends that may res ...

  • Alto-Shaam 1020ESG - page 21

    COMBITOUCH ® ESG SERIES • GAS INST ALLA TION MANUAL • MN-29246 • 19. INSTALLATION GAS SUPPLY & INSTALLATION The minimum size requir ement for gas piping or a flexible connector is 3/4 - inch (19mm). For long runs of gas piping, the pipe diameter must conform to the tables in the National Fuel Gas Code, ANSI/NFP A Z223.1. A listed gas shu ...

  • Alto-Shaam 1020ESG - page 22

    COMBITOUCH ® ESG SERIES • GAS INST ALLA TION MANUAL • MN-29246 • 20. INSTALLATION GAS SUPPLY & INSTALLATION LEAk TESTING If a pressure leak test above 1/ 2 psi is to be performed on the building supply gas piping, the shut-off gas valve and oven inlet gas supply line must be disconnected from the building supply piping before conducting ...

  • Alto-Shaam 1020ESG - page 23

    COMBITOUCH ® ESG SERIES • GAS INST ALLA TION MANUAL • MN-29246 • 21. INSTALLATION WATER SUPPLY & INSTALLATION WARNING TO PREVENT WATER PIPES FROM BURSTING, INCOMING WATER SUPPLY SHOULD BE TURNED OFF WHEN THE APPLIANCE IS NOT IN USE. WARNING WATER SUPPLY MUST BE OPEN WHEN CLEANING PROGRAM IS ACTIVATED. VERIFY WATER SUPPLY BEFORE STARTING ...

  • Alto-Shaam 1020ESG - page 24

    COMBITOUCH ® ESG SERIES • GAS INST ALLA TION MANUAL • MN-29246 • 22. INSTALLATION WATER SUPPLY & INSTALLATION WATER REQUIREMENTS WATER QUALITY MINIMUM STANDARDS TWO (2) COLD W A TER INLETS - DRINKING QUALITY ONE (1) TREA TED W A TER INLET : 3/4" NPT* ONE (1) UNTREA TED W A TER INLET : 3/4" NPT* LINE PRESSURE: 30 to 90 psi 2.8 t ...

  • Alto-Shaam 1020ESG - page 25

    COMBITOUCH ® ESG SERIES • GAS INST ALLA TION MANUAL • MN-29246 • 23. INSTALLATION WATER VALVE WATER DRAINAGE s h u t - o f f v a l v e s h o w n i n t h e o f f p o s i t i o n NOTE: THE SHUT-OFF VALVE MUST BE IN THE OPEN POSITION WHEN THE OVEN IS BEING USED. A union is required. Install a 1-1/2-inch (41mm) diameter connection, drain line an ...

  • Alto-Shaam 1020ESG - page 26

    COMBITOUCH ® ESG SERIES • GAS INST ALLA TION MANUAL • MN-29246 • 24. Stand Pipe, 1-1/2" NPT (38mm) diameter T o Dr ain - Floor Sink - Air Gap to be within the first 12" (305mm) of the ov en dr ain Drain Connection 1-1/2" NPT (38mm) Air Gap to be within the first 12" (305mm) of the ov en dr ain Manifold Pipe, a minimum of ...

  • Alto-Shaam 1020ESG - page 27

    COMBITOUCH ® ESG SERIES • GAS INST ALLA TION MANUAL • MN-29246 • 25. INSTALLATION GREASE COLLECTION HOOK-UP ( i f eQuippeD w i t h t h i s featuRe ) • Grease Collection Hose Assembly is attached to the oven in the back. • Place Grease Collection Containers inside the tray of the Mobile Grease Collection Cart. Roll into place next to the ...

  • Alto-Shaam 1020ESG - page 28

    COMBITOUCH ® ESG SERIES • GAS INST ALLA TION MANUAL • MN-29246 • 26. COMBITOUCH® CHECKLIST Use this list as a final check of oven installation conformance. Damage directly attributed to improper set up, installation, or cleaning can invalidate warranty claims. CLEARANCES: ARE ALL CLEARANCE REQUIREMENTS MET? ❑ YES ❑ NO Left: 6" (152 ...

  • Alto-Shaam 1020ESG - page 29

    COMBITOUCH ® ESG SERIES • GAS INST ALLA TION MANUAL • MN-29246 • 27. INSTALLATION This section is provided for the assistance of qualified technicians only and is not intended for use by untrained or unauthorized service personnel. If your Alto-Shaam ® unit is not operating properly , check the following before calling your Authorized Alto- ...

  • Alto-Shaam 1020ESG - page 30

    COMBITOUCH ® ESG SERIES • GAS INST ALLA TION MANUAL • MN-29246 • 28. INSTALLATION Error Code Error Call Out in Display Description of Error Possible Cause E13 Boiler Temperature High Boiler temperature overheats — Scale build up inside steam generator. — Scale build up on water level probe. — B4 Probe connection problem. — B4 probe f ...

  • Alto-Shaam 1020ESG - page 31

    COMBITOUCH ® ESG SERIES • GAS INST ALLA TION MANUAL • MN-29246 • 29. INSTALLATION ERROR CODES Error Code Error Call Out in Display Description of Error Possible Cause E34 Steam Generator Drain Pump Fault Water level in steam generator does not drop during cleaning program — Scale build up inside the steam generator drain pump. — Scale bu ...

  • Alto-Shaam 1020ESG - page 32

    COMBITOUCH ® ESG SERIES • GAS INST ALLA TION MANUAL • MN-29246 • 30. see m o to r c o n t r o l e r r o r c h a rt o n n e x t pag e INSTALLATION ERROR CODES Error Code Error Call Out in Display Description of Error Possible Cause E57 No Rinse Water During rinse no water fl ow is detected through solenoid valve — Water supply is shut off. ...

  • Alto-Shaam 1020ESG - page 33

    COMBITOUCH ® ESG SERIES • GAS INST ALLA TION MANUAL • MN-29246 • 31. INSTALLATION Type of Error Indication Release of Error Undervoltage LED fl ashing sequence, with 1 fl ash per period. Voltage of intermediate circuit is less than 250V Overvoltage LED fl ashing sequence, with 2 fl ashes per period. Voltage of intermediate circuit exceed ...

  • Alto-Shaam 1020ESG - page 34

    COMBITOUCH ® ESG SERIES • GAS INST ALLA TION MANUAL • MN-29246 • 32. INSTALLATION ERROR CODES When the oven malfunctions, an error code will appear in the display . PRESS THE ST AR T ICON TO ACKNOWLEDGE THE ERROR. The icons that begin to flash repr esent operational modes that are still usable. When the oven fault is corrected, the Combither ...

  • Alto-Shaam 1020ESG - page 35

    COMBITOUCH ® ESG SERIES • GAS INST ALLA TION MANUAL • MN-29246 • 33. ORIGINAL EQUIPMENT LIMITED WARRANTY Alto-Shaam, Inc. warrants to the original purchaser that any original part that is found to be defective in material or workmanship will, at Alto-Shaam’s option, subject to provisions hereinafter stated, be replaced with a new or rebuil ...

  • Alto-Shaam 1020ESG - page 36

    COMBITOUCH ® ESG SERIES • GAS INST ALLA TION MANUAL • MN-29246 • 34. W164 N9221 W ater Street • P .O. Box 450 • Menomonee Falls , W isconsin 53052-0450 • U.S.A. PHONE: 262.251.3800 • 800.558-8744 USA/CANADA F AX: 262.251.7067 • 800.329.8744 U.S.A. ONL Y www .alto-shaam.com All Alto-Shaam equipment is sold F.O.B. shipping point, and ...

Fabbricante Alto-Shaam Categoria Oven

I documenti che otteniamo dal fabbricante del dispositivoAlto-Shaam 1020ESG possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Alto-Shaam
- manuali per l’uso 1020ESG
- schede prodotto Alto-Shaam
- opuscoli
- o etichette energetiche Alto-Shaam 1020ESG
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Alto-Shaam 1020ESG.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Alto-Shaam 1020ESG, manuali di manutenzione, brevi manuali o manuali utente Alto-Shaam 1020ESG. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Alto-Shaam 1020ESG.

Manuali per l’uso simili

Manuale completo del dispositivo Alto-Shaam 1020ESG, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Alto-Shaam 1020ESG dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Alto-Shaam 1020ESG.

Il manuale per l’uso completo Alto-Shaam, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Alto-Shaam 1020ESG - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Alto-Shaam 1020ESG, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Alto-Shaam 1020ESG che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Alto-Shaam 1020ESG - che ci dovrebbe aiutare nei primi passi durante l'uso Alto-Shaam 1020ESG
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Alto-Shaam 1020ESG
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Alto-Shaam 1020ESG in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Alto-Shaam 1020ESG?

Utilizza il modulo sottostante

Se non hai risolto il problema con Alto-Shaam 1020ESG con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Alto-Shaam 1020ESG è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)