-
Makita 4307DW - page 1
n 72v MODEL 43071) MODEL 4307DW With Fast Charger A C only DC 145 mm x 80 mm x 61 mm 0 7 kq 50Hz 60Hr 72v 15 3 4" x 3~1j8'' x 2 318") 11 5 It)bl 1 Hi INSTRUCTION MANUAL SPEC IF I CAT IONS Model 4307D 1 1 1 190 mm 14kg 19 16' ! (15 16") 11 2") 13'64 'I 17 15r32") 13 1 IbS! 12 mm 2.200 Battery Cartrid ...
-
Makita 4307DW - page 2
IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFE- REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PER- TY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO SONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. 2. 3. 4. 5. 6. 7. 8. 9. IO. 11. 12. 13. 2 KEEP WORK AREA CLEAN. Cluttered areas and benches invit ...
-
Makita 4307DW - page 3
14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don't carry plugged-in tool with finger on switch. Be sure switch is OFF when plugging in. 16. OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only ext ...
-
Makita 4307DW - page 4
IMPORTANT SAFETY INSTRUCTIONS Length of Cord (Feet) 25 50 AWG Size of Cord 18 18 I. SAVE THESE INSTRUCTIONS - This manual 100 150 18 16 9. Do not operate charger with damaged cord or plug - replace them im- mediately. IO. Do not operate charger if it has received a sharp blow, been dropped, or other- wise damaged in any way; take it to a qualified ...
-
Makita 4307DW - page 5
ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE 1. Do not charge Battery Cartridge when temperature is BELOW 10°C (5OOF) 2. Do not attempt to use a step-up transformer, an engine generator or DC 3. Do not allow anything to cover or clog the charger vents. 4. Do not short the battery cartridge. A battery short can cause a large current ...
-
Makita 4307DW - page 6
Installing or removing battery cartridge 0 Always switch off the tool before insertion or removal of the battery cartridge. 0 To remove the battery cartridge, pull out the set plate on the tool and grasp both sides of the cartridge while withdrawing it from the barrel. 0 To insert the battery cartridge, align the tongue on the battery cartridge wit ...
-
Makita 4307DW - page 7
Mounting blade First, use the hex wrench to remove the bolt which secures the blade clamp to the blade holder shaft. With the blade teeth facing forward, place the shank of the blade over the flat side of the blade holder shaft. Then place the blade clamp over the other side of the blade shank. Secure this assembly together with bolt. Make sure tha ...
-
Makita 4307DW - page 8
CAUTION : 0 Before inserting the battery cartridge into the tool, always check to see that the trigger 0 When not operating the tool, keep the lock-off lever in the SAFETY LOCK position. .Pulling the trigger hard when the lock-off lever is set to the SAFETY LOCK position switch actuates properly and returns to the "OFF" position when rele ...
-
Makita 4307DW - page 9
Front flush cuts Loosen the bolt on the back of the base with the hex wrench, then slide the base backwards. Check the contact between the back edge of the blade and support roller, then secure the bolt. Bevel cutting 1. With the base tilted, you can make bevel cuts at any angle between 0" and 45' (left or right). 1 Roller 1 Edge of housi ...
-
Makita 4307DW - page 10
Finishing edges To trim edges or make dimensional adjust- ments, run the blade lightly along the cut edges. For smoother cutting of plywoods or other materials with easily splintered surfaces, the wood may be coated or transparent tape used over your cutting line. Using guide rule (Rip fence) When cutting widths of under 150mm(6") repeatedly, ...
-
Makita 4307DW - page 11
Using circular guide 1. Use of the circular guide insures smooth cutting of circles (radius; 200 mm; 7-7/8") and arcs. clean, under 0 Knob Fit pin into this hole 2. When attaching the circular guide, use the pin, inserting it in the center hole (arrow) and secure it with the threaded knob. The circular guide attaches to the base of the tool in ...
-
Makita 4307DW - page 12
Cutting performance The following reference table indicates the approximate cutting capacity from a single 1-hour battery charge. It may differ under some conditions. Material Thickness Cutting length Soft wood (,5,,6") 2.5 m (8.2 ft) Hard wood I ::,;: I 4 m (13ft) Mild steel I ;&:: 1 3 m (9.8 ft) CAUTION : If the tool is operated continuo ...
-
Makita 4307DW - page 13
MAINTENANCE CUATION : Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance. To maintain product SAFETY and RELlABl LITY, repairs, maintenance and adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. 1 ...
-
Makita 4307DW - page 14
ACCESSORIES CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. 0 Jig saw blade (packed 5 each in handy vinyl ...
-
Makita 4307DW - page 15
Mar 03 '86 EN CORDLESS JIG SAW Model 4307D Note: The switch and other part configuratlons may differ from country to country. 15 ...
-
Makita 4307DW - page 16
ITEM ,"&, DESCRIPTION MENE Hex Socket Head Bolt M4xB I 41 I 1 11 21 31 41 51 61 I1 91 IO 1 11 I 1 12 8 13 1 14 I I5 1 16 1 17 1 ni Lock Of1 Lever Mar 03 86 EN $:D DESCRIPTION 25 26 27 MACHINE 1 1 1 31 32 33 Spring WdahPr 4 Blade Ser Felt Motor Holder Plane Bearing 3 Leal Sprlrlg set Plat? Babe Holler P," 3 Stop Ring E 2 3 HefdlOer Fla ...
Hai una domanda su Makita 4307DW?
Utilizza il modulo sottostante
Se non hai risolto il problema con Makita 4307DW con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Makita 4307DW è probabile che voglia condividere il modo di risolverlo.