-
Miele DA 419-4 - page 1
Operating and installation instructions Cooker hood DA 416-4, DA 419-4 To avoid the risk of accidents or damage to this appliance it is essential to read these instructions before it is installed and used for the first time. M.-Nr. 07 755 460 e n-G B ...
-
Miele DA 419-4 - page 2
Caring for the environment ..........................................3 Warning and Safety instructions .....................................4 Guide to the appliance ............................................1 0 Modes of operation ...............................................1 2 Operation .......................................................1 ...
-
Miele DA 419-4 - page 3
Disposal of the packing material The transport and protective packing has been selected from materials which are environmentally friendly for disposal, and should be recycled. Packaging e.g. cling film, polystyrene and plastic wrappings must be kept out of the reach of babies and young children. Danger of suffocation! Disposal of your old appliance ...
-
Miele DA 419-4 - page 4
This appliance complies with all relevant local and national safety requirements. Inappropriate use can, however, lead to personal injury and damage to property. To avoid the risk of accidents and damage to the appliance, please read these instructions carefully before using it for the first time. They contain important information on the safety, i ...
-
Miele DA 419-4 - page 5
Technical safety ~ Before installation, check the cooker hood for visible signs of damage. Under no circumstances should you use a damaged appliance. It could be dangerous. ~ Before connecting the appliance to the mains supply, make sure that the voltage and frequency details given on the data plate correspond with the on-site electricity supply, o ...
-
Miele DA 419-4 - page 6
~ Do not connect the appliance to the mains electricity supply by a multi-socket unit or an extension lead. These do not guarantee the required safety of the appliance (e.g. danger of overheating). ~ This appliance may only be used in mobile installations if a risk assessment of the installation has been carried out by a suitably qualified engineer ...
-
Miele DA 419-4 - page 7
In order to ensure safe operation, and to prevent gases given off by the heating appliances from being drawn back into the room when the cooker hood and the heater are in operation simultaneously, an underpressure of 0.04 mbar (4 pa) is the maximum permissible in the room. Ventilation can be maintained by air inlets which must not be blocked, in wi ...
-
Miele DA 419-4 - page 8
Correct use ~ Never use an open flame beneath the cooker hood. To avoid the danger of fire, do not flambé or grill over an open flame under the cooker hood. When switched on, the cooker hood could draw flames into the filter. Fat particles drawn into the cooker hood present a fire hazard. ~ When using the cooker hood over a gas hob, ensure that an ...
-
Miele DA 419-4 - page 9
~ Safety regulations prohibit the fitting of a cooker hood over solid fuel stoves. ~ All ducting, pipework and fittings must be of non-flammable material. These can be obtained from the Miele Spare Parts department or from builders' merchants. ~ The appliance must not be connected to a chimney or vent flue which is in use. Neither should it be ...
-
Miele DA 419-4 - page 10
Guide to the appliance 10 ...
-
Miele DA 419-4 - page 11
a Telescopic extension piece b Tower c Canopy d Touch controls e Grease filters f Recirculation grille (only for recirculation mode) g Hob lighting h Charcoal filter (special accessory for recirculation mode) i On/Off control for the fan j Controls to select fan power level k On/Off control for hob lighting Guide to the appliance 11 ...
-
Miele DA 419-4 - page 12
The cooker hood works with . . . air extraction: The air is drawn in and cleaned by the grease filters and directed outside. If the on-site ventilation system does not have a non-return flap , the non-return flap supplied with the appliance must be fitted in the exhaust socket in the motor unit. Having a non-return flap fitted in the ducting ensure ...
-
Miele DA 419-4 - page 13
To switch the fan on s ^ Press the On/Off control s . The fan will come on at power level lI. If the cooker hood has been connected to a window contact switch via the Miele DSM 400 control module, then the fan cannot be switched on if the window is shut. The s symbol flashes. To select a power level - / + ^ To select a lower power level, press the ...
-
Miele DA 419-4 - page 14
To switch the fan off s ^ Press the On/Off control s to switch the fan off. The s symbol goes out. It is advisable to run the fan for a few minutes after cooking has finished to neutralise any lingering odours in the air, whether you are using air extraction or recirculation mode. Hob lighting I ^ The hob lighting can be switched on and off indepen ...
-
Miele DA 419-4 - page 15
A range of Miele branded cleaning and conditioning products is available to order from Miele (see back page for details) or the via the internet at www.miele-shop.com. Before any cleaning or maintenance work is carried out, disconnect the cooker hood from the mains supply. Ensure that: – it is switched off at the isolator, or – it is switched o ...
-
Miele DA 419-4 - page 16
Controls The controls may suffer discolouration or damage if soiling is left on them for too long. Remove soiling straight away. ^ Observe the General notes on cleaning earlier in this section. Do not use stainless steel cleaning agents on the controls. Grease filters The re-usable metal grease filters in the appliance remove solid particles (greas ...
-
Miele DA 419-4 - page 17
Cleaning the grease filters by hand ^ Clean the filters with a soft nylon brush in a mild solution of hot water and a little washing-up liquid. Do not use "neat" washing up liquid. Do not use: – cleaning agents containing descaling agents, – powder cleaners, cream cleaners or abrasive all-purpose cleaners. – oven sprays. Cleaning th ...
-
Miele DA 419-4 - page 18
Fitting and replacing the charcoal filter If the cooker hood is connected for recirculation, a charcoal filter must be inserted in addition to the grease filters. This is designed to absorb cooking odours. It is fitted in the canopy above the grease filters. New charcoal filters can be purchased from your Miele dealer, from the Miele Spare Parts De ...
-
Miele DA 419-4 - page 19
Changing a halogen lamp ^ Before any cleaning or maintenance work, disconnect the cooker hood from the mains supply. Ensure that: – it is switched off at the isolator, or – it is switched off at the wall socket and the plug is withdrawn, or – the fuse from the fused spur connection unit is withdrawn, or – the mains fuse is disconnected, or ...
-
Miele DA 419-4 - page 20
The diagram is not drawn to scale. Appliance dimensions 20 ...
-
Miele DA 419-4 - page 21
a Extraction b Recirculation c Ventilation grille positioned at the top for recirculation d , e ( e is not required for recirculation mode cooker hoods).The shaded areas represent the wall or ceiling area for the vent cut-out and for fitting the connection socket. For recirculation mode, only a connection socket needs to be fitted. Connection for a ...
-
Miele DA 419-4 - page 22
Drilling diagram This diagram illustrates where holes for Ø 5 mm screws need to be drilled in the rear wall. * The dimensions between the ceiling and the middle bracket can vary depending on the position of the vent cut-out and the connection socket. It should be installed as low as possible. If the cooker hood is being secured directly to the wal ...
-
Miele DA 419-4 - page 23
Before installation, it is important to read the information given on the following pages as well as the "Appliance dimensions" and the "Warning and Safety instructions" at the beginning of this booklet. This is particularly crucial when using the cooker hood at the same time as a heating appliance that relies on oxygen from the ...
-
Miele DA 419-4 - page 24
Assembly parts Installation 24 ...
-
Miele DA 419-4 - page 25
a 3 protective sheets for use when fitting the tower. b 1 exhaust connection for exhaust ducting C 150 mm. c 1 reducing collar for exhaust ducting C 125 mm. d 1 non-return valve for fitting into the exhaust connection on the motor unit (not for recirculation mode). e Upper wall bracket for securing the extension piece. f Middle wall bracket for sec ...
-
Miele DA 419-4 - page 26
Important: To avoid the danger of toxic fumes, please observe the Warning and Safety instructions. This is especially crucial when using the cooker hood at the same time as another heating appliance which relies on air from the same room. The cooker hood should be installed according to local and national building regulations. Seek approval from th ...
-
Miele DA 419-4 - page 27
Condensate trap (optional accessory) In addition to insulating the exhaust ducting, we recommend that a suitable condensate trap is also installed to collect and evaporate any condensate which may occur. Condensate traps are available for C 125 mm or C 150 mm ducting. When installing a condensate trap, ensure that it is positioned vertically and if ...
-
Miele DA 419-4 - page 28
Silencer (optional accessory) To achieve even further reductions in noise levels, a special silencer can be fitted in the ducting system. ...with air extraction: The silencer not only reduces noise from the motor, but also sounds from outside (e.g. traffic noise). For this reason the silencer must be positioned as close as possible to where the duc ...
-
Miele DA 419-4 - page 29
All electrical work should be undertaken by a suitably qualified and competent person in strict accordance with current national and local safety regulations (BS 7671 in the UK). Installation, repairs and other work by unqualified persons could be dangerous, for which the manufacturer cannot be held liable. Ensure power is not supplied to the appli ...
-
Miele DA 419-4 - page 30
The Miele DSM 400 Control module can be used to combine the cooker hood with other components. It enables the following: Connection to a window contact switch If adequate ventilation to the room can only be ensured by having a window open when the cooker hood is in use at the same time as a heating appliance which depends on the air from the same r ...
-
Miele DA 419-4 - page 31
Connection to a light switch The control module can be used to switch on the cooker hood lighting via a light switch in the house. Installation The tower needs to be removed before the control module can be fitted to the fan unit. The control module is supplied with its own detailed operating and installation instructions. Operation with Control mo ...
-
Miele DA 419-4 - page 32
In the event of a fault which you cannot correct yourself, or if the appliance is under guarantee, please contact: – Your Miele Dealer / Chartered Agent or – The Miele Service Department (see back cover for address). When contacting your Dealer or Miele, please quote the model and serial number of your appliance. These are shown on the data pla ...
-
Miele DA 419-4 - page 33
Total connected load DA 416-4 ...................1 6 0W DA 419-4 ...................1 8 0W - Fan motor .................1 2 0W - Hob lighting DA 416-4 .................2x2 0W DA 419-4 .................3x2 0W Voltage ....................2 3 0V Frequency ..................5 0H z Fuse rating (UK) ................5A Electrical cable length .........1 . ...
-
Miele DA 419-4 - page 34
34 ...
-
Miele DA 419-4 - page 35
35 ...
-
Miele DA 419-4 - page 36
Alteration rights reserved / 2910 M.-Nr. 07 755 460 / 01 ...
Hai una domanda su Miele DA 419-4?
Utilizza il modulo sottostante
Se non hai risolto il problema con Miele DA 419-4 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Miele DA 419-4 è probabile che voglia condividere il modo di risolverlo.