Manuale per l’uso Electrolux Built-In Side-by-side Refrigerators

22 pagine 0.41 mb
Scarica

Vai alla pagina of 22

Summary
  • Electrolux Built-In Side-by-side Refrigerators - page 1

    Installation Instructions Built-In Side-By-Side Refrigerators If you have questions, call 1-877-4ELECTROLUX 877-435-3287 or visit our website at: BEFORE YOU BEGIN Read these instructions completely and carefully . • IMPOR T ANT — Observe all governing codes and ordinances. • Note to Installer – Be sure to leave these instructions for the co ...

  • Electrolux Built-In Side-by-side Refrigerators - page 2

    Installation Instructions 16 HARDW ARE SUPPLIED • Anti-T ip brackets Anti-T ip Brackets MA TERIALS REQUIRED • 36 ″ long, 2 ″ x 4 ″ wood block for Anti-T ip bracket installation • #12 or #14 wood screws for Anti-T ip bracket • Screws to secure refrigerator to cabinets • 1/4 ″ O.D. copper water line tubing. • W ater shutoff valve ...

  • Electrolux Built-In Side-by-side Refrigerators - page 3

    THE INST ALLA TION SP ACE Water and Electrical Locations The opening must be prepared with the electrical and water supply located as shown. The cutout depth must be 24 ″ The refrigerator will project forward, slightly beyond adjacent cabinets, depending on your installation. Additional Specifications • A 120 volt, 60Hz, 15 or 20 amp power supp ...

  • Electrolux Built-In Side-by-side Refrigerators - page 4

    1/2" 1" 3/4" Custom Panel (Nominal Size) 1/4" 1/2" 3/4" 2" 1-1/4" 1-1/2" 1-3/4" 3" 2-1/4" 2-1/2" 2-3/4" 1/4" 1/2" 3/4" Fresh Food Door Backer Panel 23-7/8" From Rear of Refrigerator 1" Refrigerator Case Trim 3/4" 1/4" 1" T op View 130° Doo ...

  • Electrolux Built-In Side-by-side Refrigerators - page 5

    1/2" 1/4" 1/2" 3/4" 1" 1-1/4" 1-1/2" 23-7/8" From Rear of Refrigerator 3/4" Custom Panel (Nominal Size) Case T rim Refrigerator Fresh Food Door Backer Panel 3/4" 1/4" 1" T op View 90° Door Swing (optional setting) Scale 1:1 Installation Instructions 19 ...

  • Electrolux Built-In Side-by-side Refrigerators - page 6

    CUSTOMIZA TION BASICS: Stainless Steel Wrapped Models Stainless Steel Wrapped Refrigerators Stainless Steel wrapped refrigerators have wrapped doors and grille panels, and beveled edges. These models are shipped ready for installation. T rimmed Models T rimmed Refrigerator Panels T rimmed refrigerators are designed to be customized with decorative ...

  • Electrolux Built-In Side-by-side Refrigerators - page 7

    1/4 ″ FRAMED P ANEL DIMENSIONS If you choose to install framed panels, they must be cut to the dimensions shown. The panels will slide into the frame on the door and grille. IMPORT ANT NOTE: Maximum weight for Fresh Food panel is 70 pounds and 30 pounds total for Freezer panels. IMPORT ANT NOTE: Dispenser T rim The refrigerator is supplied with f ...

  • Electrolux Built-In Side-by-side Refrigerators - page 8

    3/4 ″ FRAMED CUSTOM P ANEL OPTION For a more custom appearance, 3/4 ″ framed custom panels may be installed on trimmed models. The overlay panel is secured to a 1/4 ″ finished backer panel. The assembled custom panel then slides into the trim with the same procedure described on page 33. 3/4 ″ FULL-WIDTH OVERLA Y CUSTOM P ANEL OPTION This d ...

  • Electrolux Built-In Side-by-side Refrigerators - page 9

    3/8" 3-1/8" 5/16" 1" Thick Max. or 3/4" Plus 1/4" Backer B 2-1/2" 3-1/8" Min. 1/4" Max. A 5/16" Required for Optimal Handle Clearance 3/4 ″ FRAMED CUSTOM WOOD P ANELS Secured to a 1/4 ″ finished backer panel. This design provides a framed appearance. Fresh Food Panel Installation Instructions 23 ...

  • Electrolux Built-In Side-by-side Refrigerators - page 10

    2-1/2" 3-1/8" Min. 1/4" Max. Required for Optimal Handle Clearance 3/8" 3-1/8" 1" Thick Max. or 3/4" Plus 1/4" Backer 5/16" A 5/16" B 3/8" 1" Thick Max. or 3/4" Plus 1/4" Backer 5/16" 5/16" 3-1/8" A B 1" Thick Max. or 3/4" Plus 1/4" Backer 5/16" ...

  • Electrolux Built-In Side-by-side Refrigerators - page 11

    1/4" Max. Required for Optimal Handle Clearance 3-1/8" 2-1/2" 3-1/8" Min. B A 3/4 ″ FULL-WIDTH OVERLA Y CUSTOM P ANELS This panel design provides a nearly trimless appearance. Assemble the spacer panel onto the finished backer panel. Allow 1/2 ″ clearance on the top, bottom and hinge side. Allow 3-5/8 ″ on the handle side. ...

  • Electrolux Built-In Side-by-side Refrigerators - page 12

    3-1/8" Min. 1/4" Max. Required for Optimal Handle Clearance 3-1/8" 3-1/8" 5/16" 5/16" A B A B A B 2-1/2" 3/4 ″ FULL-WIDTH OVERLA Y CUSTOM P ANELS This panel design provides a nearly trimless appearance. Assemble the spacer panel onto the backer panel. Allow 1/2 ″ clearance on all four sides of the grille space ...

  • Electrolux Built-In Side-by-side Refrigerators - page 13

    GROUNDING THE REFRIGERA TOR IMPORT ANT — Please read carefully FOR PERSONAL SAFETY , THIS APPLIANCE MUST BE PROPERL Y GROUNDED. The power supply cord of this appliance is equipped with a three-prong (grounding) plug which mates with a standard three- prong (grounding) wall receptacle to minimize the possibility of electric shock hazard from this ...

  • Electrolux Built-In Side-by-side Refrigerators - page 14

    1 REMOVE P ACKAGING CAUTION: Refrigerator is T op-Heavy —be careful when moving. When using an appliance dolly , handle from Freezer side only . • Carefully cut banding at the top and bottom; remove outer carton. • Slide out rear corner posts (2). • Slide carton off top of cabinet. NOTE: DO NOT LA Y CABINET DOWN IN ORDER TO REMOVE SKID! • ...

  • Electrolux Built-In Side-by-side Refrigerators - page 15

    2 INST ALL W A TER LINE • A cold water supply is required for automatic icemaker operation. The water pressure must be between 40 and 120 psi. • Route 1/4 ″ O.D. copper tubing between cold water line and the water connection location. • T ubing should be long enough to extend to the front of the refrigerator . Allow enough tubing to accommo ...

  • Electrolux Built-In Side-by-side Refrigerators - page 16

    3 INST ALL SIDE P ANELS SKIP THIS STEP WHEN NOT USING SIDE P ANELS If you are using 1/4" side panels, they should be inserted into the case trim. Fasten the panels to the refrigerator with the 3M Dual Lock adhesive strips before setting refrigerator in place. 4A AL TERNA TE ANTI-TIP PRECAUTIONS SKIP THIS STEP WHEN USING ANTI-TIP BRACKETS All P ...

  • Electrolux Built-In Side-by-side Refrigerators - page 17

    7 LEVEL REFRIGERA TOR All models have 4-point leveling. The front and back are supported by leveling legs. Both are accessible from the front of the refrigerator . • T o level the back of the refrigerator , turn the 1/2 ″ hex nut located above the front wheels. T urn clockwise to raise or counterclockwise to lower the refrigerator . • For fro ...

  • Electrolux Built-In Side-by-side Refrigerators - page 18

    10 INST ALL GRILLE P ANEL • Raise the grille panel to the stop position. • Remove 4 screws on bottom trim; retain all screws. • Remove bottom trim. • NOTE: Stainless steel and acrylic panels are covered with a protective film. Remove the film before installing the panel. • Slide panel over the metal backer panel and under the trim. • If ...

  • Electrolux Built-In Side-by-side Refrigerators - page 19

    11A Install 1/4 ″ Decorative Panels: • Remove Handles Open door to 90°. Remove 5 Phillips head screws from the Fresh Food and Freezer door handles; retain all screws. Lift off door handles. • Install Door Panels NOTE: Stainless steel and acr ylic panels are covered with a protective film. Remove the film before installing the panel. Carefull ...

  • Electrolux Built-In Side-by-side Refrigerators - page 20

    11B 1. Remove handles from cartoning and any other protective packaging. 2. Place handle over pre-installed shoulder bolts (A) that are fastened into door in four locations. 3. While supporting handle and looking at upper end cap, fasten top-most allen set screw (B) with supplied allen wrench, then fasten bottom allen set screw (C). See Figure 1. 4 ...

  • Electrolux Built-In Side-by-side Refrigerators - page 21

    13 TURN ON THE POWER • Set the Master Power switch to the I (ON) position. • Check to make sure power to refrigerator is on by opening refrigerator door to see if interior lights are on. • The temperature controls are preset at 37° for the Fresh Food section and 0° for the Freezer section. • Allow 24 hours to stabilize before making adjus ...

  • Electrolux Built-In Side-by-side Refrigerators - page 22

    16 DOOR ALIGNMENT • Stand back from the refrigerator to inspect the door alignment. • Shipping or the addition of heavy door panels may have caused the doors to move slightly out of alignment. • If necessary , the Fresh Food door may be adjusted up or down to align with the Freezer door . • Loosen the leveling mechanism. • Use a 7/32 ″ ...

Fabbricante Electrolux Categoria Refrigerator

I documenti che otteniamo dal fabbricante del dispositivoElectrolux Built-In Side-by-side Refrigerators possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Electrolux
- manuali per l’uso Built-In Side-by-side Refrigerators
- schede prodotto Electrolux
- opuscoli
- o etichette energetiche Electrolux Built-In Side-by-side Refrigerators
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Electrolux Built-In Side-by-side Refrigerators.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Electrolux Built-In Side-by-side Refrigerators, manuali di manutenzione, brevi manuali o manuali utente Electrolux Built-In Side-by-side Refrigerators. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Electrolux Built-In Side-by-side Refrigerators.

Manuali per l’uso simili

Manuale completo del dispositivo Electrolux Built-In Side-by-side Refrigerators, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Electrolux Built-In Side-by-side Refrigerators dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Electrolux Built-In Side-by-side Refrigerators.

Il manuale per l’uso completo Electrolux, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Electrolux Built-In Side-by-side Refrigerators - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Electrolux Built-In Side-by-side Refrigerators, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Electrolux Built-In Side-by-side Refrigerators che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Electrolux Built-In Side-by-side Refrigerators - che ci dovrebbe aiutare nei primi passi durante l'uso Electrolux Built-In Side-by-side Refrigerators
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Electrolux Built-In Side-by-side Refrigerators
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Electrolux Built-In Side-by-side Refrigerators in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Electrolux Built-In Side-by-side Refrigerators?

Utilizza il modulo sottostante

Se non hai risolto il problema con Electrolux Built-In Side-by-side Refrigerators con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Electrolux Built-In Side-by-side Refrigerators è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Commenti (0)