Italiano dropdown-ico

Manuale per l’uso Craftsman 315.2696

22 pagine 0.96 mb
Scarica

Vai alla pagina of 22

Summary
  • Craftsman 315.2696 - page 1

    Owner's Manual 5-1/2 in. PROFESSIONAL CORDLESS TRIM SAW Model No. 315.269600 Save this manual for future reference _, CAUTION: Read and follow all Safety Rules and Operating Instructions before first use of this product. Customer Help Line: 1-800-932-3188 Sears, Roebuck and Co., Hoffman Estates, IL 60179 USA Visit the Craftsman web page: www.s ...

  • Craftsman 315.2696 - page 2

    • Table of Contents .., .................. '...................................................................................................................... 2 • Warranty and Introduction_ ............................................................................................................................. 2 • Rules For Safe ...

  • Craftsman 315.2696 - page 3

    The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and the explanations with them, deserve your careful attention and understanding. The safety warnings do not by themselves eliminate any danger. The instructions or warnings they give are notsubstitutes for proper accident prevention measures. SYMBOL ...

  • Craftsman 315.2696 - page 4

    RULES FOR SAFE OPERATION (Continued) • MAINTAIN TOOLS WITH CARE. Keep tools sharp at all times, and clean for best and safest performance. Follow instructions for lubricating and changing accessories. • REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before tuming it on. ? ...

  • Craftsman 315.2696 - page 5

    RULES FOR SAFE OPERATION (Continued) m Make sure cord is located so that it will not be stepped on, tripped over, or otherwise subjected to damage or stress. An extension cord should not be used unless absolutely necessary. Use of improper extension cord could result in a risk of fire and electric shock. If extension cord must be used, make sure: a ...

  • Craftsman 315.2696 - page 6

    Blade Diameter Blade Arbor Cutting Depth at 0 ° Bevel Cut Cutting Depth at 45 ° Bevel Cut 5-1/2 in. 318 in. 1-9/16 in. 1-1/8 in. No Load Speed Motor Charge Rate Charger Rating 3,800 RPM 14.4 Volts DC 1 Hour 120 volts, 60 Hz, AC Your trim saw has been shipped completely assembled except for the blade. Inspect it carefully to make sure no breakage ...

  • Craftsman 315.2696 - page 7

    CHARGER See Figure 2. Your charger has a =.key hole" hanging feature for convenient, space saving storage. Screws should be installed so that center distances are 1-7/16 inches apad. YELLOWANDGREEN LIGHT INDICATE SOFTSTARTMODE GREENLIGHT "ON" REDUGHT"ON"INDICATES FASTCHARGING MODE BATrERY CHARGER BATrERY PACK 1-7/16 in. BAC ...

  • Craftsman 315.2696 - page 8

    KNOW YOUR TRIM SAW See Figure 2. Before attempting to use any tool familiarize yourself with all operating features and safety requirements. Features include easily operated bevel cut and depth of cut adjustment mechanisms; positive O ° bevel stop; spindle lock; and blade wrench storage. _, WARNING: If any parts are missing, do not operate tool un ...

  • Craftsman 315.2696 - page 9

    _k WARNING: Always wear safety goggles or safety glasses with side shields when operating tools. Failure to do so could result in .objects being thrown into your eyes, resulting in possible serious injury. _k WARNING: Do not allow familiarity with your trim saw to make you careless. Remember that a careless fraction of a second is sufficient to inf ...

  • Craftsman 315.2696 - page 10

    _i, WARNING: Always remove battery pack from your saw when you are assembling parts, making adjustments, assembling or removing blades, cleaning, or when not in use. Removing battery pack will prevent accidental starting that could cause sedous personal injury. TO REMOVE BATI'ERY PACK • Locate latches on end of battery pack and depress to re ...

  • Craftsman 315.2696 - page 11

    • Fit saw blade inside lower blade guard and onto spindle. Note: The saw teeth point upward at the front of saw as shown in figure 4. • Replace outer blade washer. • Depress spindle lock button, then mplaoe blade screw. Tighten blade screw securely. Note: Turn blade screw countemlockwise to tighten. • Return blade wrench to storage area. RE ...

  • Craftsman 315.2696 - page 12

    KICKBACK See Figure 7. BLADESET TOO DEEP KICKBACK Fig. 7 The best guard against kickback Is to avoid dangerous Idractlces. Kickback occurs when the blade stalls rapidly and the saw is driven back towards you, Blade stalling is caused by any action which pinches the blade in the wood. _k DANGER: Release switch immediately if blade binds or saw stall ...

  • Craftsman 315.2696 - page 13

    • When making a cut use steady, even pressure. Never force cuts. • Do not cut warped or wet lumber. • Always hold your saw firmly with both hands and keep your body in a balanced position so as to resist the forces of kickback should it occur. When using your saw, always stay alert and exercise control. Do not remove your saw from workpiece w ...

  • Craftsman 315.2696 - page 14

    TO HELP MAINTAIN CONTROL: • Always support your workpiece near the cut. • Support your workpiece so the cut will be on yo=;r left. • Clamp your workpiece so it will not move during the cut. Place your workpiece with its good side down. Note: The good side is the side on which appearance is important. Before beginning a cut, draw a guideline a ...

  • Craftsman 315.2696 - page 15

    TOP VIEW OF SAW GUIDELINE AUGN OUTER BLADE GUIDE NOTCH ON SAW BASE WITH UNE OF CUT AS SHOWN WHEN MAKING CROSS CUTS OR RIP CUTS Fig.16 Since blade thicknesses vary, always make a trial cut in scrap material along a guideline to determine how much, if any, the guideline must be offset to produce an accurate cut. Note: The distance from the line of cu ...

  • Craftsman 315.2696 - page 16

    TO BEVEL CUT The angle of cut of your saw may be adjusted to any desired setting between zero and 50 ° . Note: When making cuts at 50 ° , blade should be set at full depth of cut. When making 45 ° bevel cuts, there is a notch in the saw base to help you line up the blade with the line of cut. See Figure 19. BEVEL BEVEL SCALE ADJUSTMENT KNOB BLAD ...

  • Craftsman 315.2696 - page 17

    POSITIVE 0 ° BEVEL STOP See Figure 21. ADJUSTMENT BEVEL SCREW ADJUSTMENT KNOB HEX NUT POSITIVE 0 ° BEVELSTOP T COMBINATION SQUARE BLADE • Turn screw and adjust base until square with saw blade. • Tighten hex nut and bevel adjustment knob securely. WARNING: Attempting to make cuts without bevel adjustment knob securely tightened can result in ...

  • Craftsman 315.2696 - page 18

    18 ...

  • Craftsman 315.2696 - page 19

    ,_ WARNING: When servicing, use only identical Craftsman replacement parts. Use of any other part may create a hazard or cause product damage. Avoid using solvents.when cleaning plastic pads. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, dust, oil, ...

  • Craftsman 315.2696 - page 20

    6 5 CRAFTSMAN CORDLESS TRIM SAW - MODEL NUMBER 315.269600 27 O 12 • _26 14 18 28 19 20 23 10 21 22 [ 24 "2 _ 2_ ' 25 20 ...

  • Craftsman 315.2696 - page 21

    I CRAFTSMAN CORDLESS TRIM SAW- MODEL NUMBER 315.269600 The model number will be found on a plate attached to the motor housing. Always mention the model number in all correspondence regarding your CORDLESS TRIM SAW or when ordering repair pads. SEE BACK PAGE FOR PARTS ORDERING INSTRUCTIONS ] Key No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Part Number 9 ...

  • Craftsman 315.2696 - page 22

    For in,home major brand repair service: Call 24 hours a day, 7 days a week 1-800-4-MY-Home s. (1-800-469-4663) Para peoir servicio de reparacibn a domicilio - 1-800-676-5811 In Canada for all your service and parts needs call - 1-800-665-4455 Au Canada pour tout le service ou les pi_ces For the repair or replacement parts you need: Call 7 am - 7 pr ...

Fabbricante Craftsman Categoria Saw

I documenti che otteniamo dal fabbricante del dispositivoCraftsman 315.2696 possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Craftsman
- manuali per l’uso 315.2696
- schede prodotto Craftsman
- opuscoli
- o etichette energetiche Craftsman 315.2696
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Craftsman 315.2696.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Craftsman 315.2696, manuali di manutenzione, brevi manuali o manuali utente Craftsman 315.2696. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Craftsman 315.2696.

Manuali per l’uso simili

Manuale completo del dispositivo Craftsman 315.2696, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Craftsman 315.2696 dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Craftsman 315.2696.

Il manuale per l’uso completo Craftsman, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Craftsman 315.2696 - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Craftsman 315.2696, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Craftsman 315.2696 che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Craftsman 315.2696 - che ci dovrebbe aiutare nei primi passi durante l'uso Craftsman 315.2696
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Craftsman 315.2696
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Craftsman 315.2696 in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Craftsman 315.2696?

Utilizza il modulo sottostante

Se non hai risolto il problema con Craftsman 315.2696 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Craftsman 315.2696 è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)