Italiano dropdown-ico

Manuale per l’uso Cisco Systems CISCO1751

34 pagine 0.53 mb
Scarica

Vai alla pagina of 34

Summary
  • Cisco Systems CISCO1751 - page 1

    Corporate Headquarters: Copyright © 2003 Cisco Systems, Inc. All rights reserved. Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA Cisco 1751 Voice-over-IP Quick Start Guide The Cisco 1751 V oice ov er IP Quick Start Guid e explains ho w to install W AN Interface Cards and V oice Interface Cards, ho w to run conf iguration t ...

  • Cisco Systems CISCO1751 - page 2

    2 Cisco 1751 Voice-over-I P Quick Start Guide 78-11259-05 Conventions Conventions This document uses the f ollow ing con venti ons: • Commands and ke ywords are in bol dface . • Optional k eywords or arguments ar e in square brackets. • V ariables for which you supply v alues are in italic . • T itles of publications and new w ords or conce ...

  • Cisco Systems CISCO1751 - page 3

    3 Cisco 1751 Voice-over-IP Quick Start Guide 78-11259-05 Installing WAN a nd Voice Interface Card s Figure 1 V oice Interf ace Card Y ou should install and cable VICs before perfo rming the software conf iguration tasks e xplained later in this guide. War ni n g Be sure to observe all warnings and safety precautions in the in stallation guide. Caut ...

  • Cisco Systems CISCO1751 - page 4

    4 Cisco 1751 Voice-over-I P Quick Start Guide 78-11259-05 Installing WAN and Voice Interface Cards Figure 2 Inserting a WIC or VIC in the Rout er If you need m ore deta iled installa tion ins tructions, re fer to the C i s c o WA N I n t e r f a c e C a rd s H a rd w a re Installation Gu ide . Connecting the FXS, FXO, and E&M VICs to the Networ ...

  • Cisco Systems CISCO1751 - page 5

    5 Cisco 1751 Voice-over-IP Quick Start Guide 78-11259-05 Installing WAN a nd Voice Interface Card s Figure 3 Connecting VICs to the Networ k When you are finished, reinstall an y network interf ace cables you removed and turn on po wer to the router . Connector Pinouts for FXS, FXO, and E&M VICs Figure 4 sho ws the wiring patterns for FXS and F ...

  • Cisco Systems CISCO1751 - page 6

    6 Cisco 1751 Voice-over-I P Quick Start Guide 78-11259-05 Installing WAN and Voice Interface Cards Figure 5 sho ws the wiring pattern for an E&M connector , and Ta b l e 2 lists the E&M pinouts. Note The E&M VIC pinout depends on the PBX type and co nnection. Pins that are not used should not be connected. Figure 5 RJ-48S Wir ing f or E ...

  • Cisco Systems CISCO1751 - page 7

    7 Cisco 1751 Voice-over-IP Quick Start Guide 78-11259-05 Installing WAN a nd Voice Interface Card s The card is illustrated in Figure 6 . Figure 6 2-P ort ISDN BRI Card F ront P anel Connecting the 2-Port ISDN BRI Card Use the straight-t hrough RJ-45 cable to con nect the 2-port ISDN BRI card to the ISDN netw ork through a telephone wall outlet. Ca ...

  • Cisco Systems CISCO1751 - page 8

    8 Cisco 1751 Voice-over-I P Quick Start Guide 78-11259-05 Installing WAN and Voice Interface Cards Note When the interface is configured as NT and is connecti ng to a TE device, the cabl e must ha ve the transmit and receiv e pins swapped (crossover cable). (See Ta b l e 3 .) Step 3 Connect the other end to t he RJ-45 wall outlet. ISDN BRI Card LED ...

  • Cisco Systems CISCO1751 - page 9

    9 Cisco 1751 Voice-over-IP Quick Start Guide 78-11259-05 Cisco Router and Security Devic e Manager Figure 8 Cisco 1 751 Router Slot Number ing Figure 9 sho ws the VIC port numberin g. Figur e 9 VIC P ort Numb er ing Example If you install a VI C in both SLO T 0 and SLO T 1 of the router , the ports in each of these slots w ould be numbered as follo ...

  • Cisco Systems CISCO1751 - page 10

    10 Cisco 1751 Voice-over-I P Quick Start Guide 78-11259-05 Configuring Voice-over-I P T o obtain the SDM release notes, and other SDM d ocumentation, go to http://www .cisco.com/go/sdm and click the T echnical Documentation link. Note If you need to configure V oice-ov er-IP , use the Configuring V oi ce-ov er-IP section of this Quick Start Guide. ...

  • Cisco Systems CISCO1751 - page 11

    11 Cisco 1751 Voice-over-IP Quick Start Guide 78-11259-05 Configuring Voice-over-IP If the installer does not start after a few seconds, select Start>Run , and enter d:setup where d is your CD-R OM driv e. Step 5 Follo w the instructio ns on the screen to install the Cisco Conf igMaker application. T o learn about the Cisco ConfigMak er applic ...

  • Cisco Systems CISCO1751 - page 12

    12 Cisco 1751 Voice-over-I P Quick Start Guide 78-11259-05 Configuring Voice-over-I P Information for International Users International users mu st set the v alues of certain v oice-port commands, like cptone , that are specif ic to their country . Refer to the Cisco 1751 Router Sof twar e Conf iguration Gu ide for details . Entering Configuration ...

  • Cisco Systems CISCO1751 - page 13

    13 Cisco 1751 Voice-over-IP Quick Start Guide 78-11259-05 Configuring Voice-over-IP For complete in formation about the g lobal configurati on commands and about co nfigurin g LAN and W AN interfaces on your router , refer to the Cisc o IOS configuration gui des and command references. The rest of this guide e xplains ho w to configure yo ur router ...

  • Cisco Systems CISCO1751 - page 14

    14 Cisco 1751 Voice-over-I P Quick Start Guide 78-11259-05 Configuring Voice-over-I P Dial Plan Use a dial plan to map the destination t elephone numbers with the v oice ports on the router . In North America, the North American Numbering Plan (NANP) is used, which consists of an area code, an off ice code, and a station code. Area codes are assign ...

  • Cisco Systems CISCO1751 - page 15

    15 Cisco 1751 Voice-over-IP Quick Start Guide 78-11259-05 Configuring Voice-over-IP Y ou can use a period (.) as a wildca rd character representing a single digit in a t elephone number . Y ou can use the show num-exp command to verify the number expansion i nformation. East# show num-exp [dialed-number] After you ha ve conf igured dial peers and a ...

  • Cisco Systems CISCO1751 - page 16

    16 Cisco 1751 Voice-over-I P Quick Start Guide 78-11259-05 Configuring Voice-over-I P Note Y ou can name your router by using the g lobal configuration hostname command. (For info rmation about port numbering, refer to th e section on “Determining V oice Port Numbering” earlier in this guide.) Note If your router is configur ed with three VICs, ...

  • Cisco Systems CISCO1751 - page 17

    17 Cisco 1751 Voice-over-IP Quick Start Guide 78-11259-05 Configuring Voice-over-IP Note The telephone numbers used in this guide are only e xamples and are in valid f or public use in the United States. When you conf igure your network, be sure to substit ute your o wn telephone numbers. T o configure th e router with the dial-peer information in ...

  • Cisco Systems CISCO1751 - page 18

    18 Cisco 1751 Voice-over-I P Quick Start Guide 78-11259-05 Configuring Voice-over-I P Figur e 13 Basic V oice Networ k (East Router) Enter the follo wing commands to configure the l ocal ports on the East Router with th e dial-peer informatio n in Ta b l e 8 : East(config)# dial-peer voice 901 pots East(config-dial-peer)# destination-pattern 191955 ...

  • Cisco Systems CISCO1751 - page 19

    19 Cisco 1751 Voice-over-IP Quick Start Guide 78-11259-05 Configuring Voice-over-IP Checking Dial Peer Configuration If you conf igured PO TS dial peers on your router b y following these e xamples, you can place calls between telephones c onnected to the same router . Y ou can also use the show dial-peer voice command to verify that the d ata you ...

  • Cisco Systems CISCO1751 - page 20

    20 Cisco 1751 Voice-over-I P Quick Start Guide 78-11259-05 Configuring Voice-over-I P Construct a table similar to Ta b l e 1 0 for your o wn routers, assigning your o wn telephone numbers, IP addresses, and dial-peer tags. Note The IP addresses sho wn in this guide are meant only as examples. When yo u configure your network, be sure to substitute ...

  • Cisco Systems CISCO1751 - page 21

    21 Cisco 1751 Voice-over-IP Quick Start Guide 78-11259-05 Configuring Voice-over-IP Enter the follo wing information o n the East router to create the dial-peer configuration gi ven in Ta b l e 1 1 : East(config)# num-exp 5.... 1408555.... East(config)# dial-peer voice 801 voip East(config-dial-peer)# destination-pattern 1408555.... East(config-dia ...

  • Cisco Systems CISCO1751 - page 22

    22 Cisco 1751 Voice-over-I P Quick Start Guide 78-11259-05 Configuring Voice-over-I P Figure 18 FX O Gatew ay t o PSTN T o create a PO TS dial peer for an FXS interface as explained earlier , you enter the complete telephone number of the attached telephone as the desti nation pattern for incoming calls. Ho wev er , to create a PO TS dial peer for ...

  • Cisco Systems CISCO1751 - page 23

    23 Cisco 1751 Voice-over-IP Quick Start Guide 78-11259-05 Configuring Voice-over-IP Checking FXO Configuration If you conf igured your FXO interf ace according to this example, y ou can place outgoing calls over the PSTN. If you ha ve troub le placing calls, use the sh ow voi ce port command to make sure that the VIC is installed co rr ectly . Use ...

  • Cisco Systems CISCO1751 - page 24

    24 Cisco 1751 Voice-over-I P Quick Start Guide 78-11259-05 Configuring Voice-over-I P Both PBXs in this e xample use E&M interface T ype 2, with four -wire operation and immed iate-start signaling. The v alues for your conf iguration depend on your PBX and are av ailable from your telecommunications d epartment or the PBX manufacturer . For mor ...

  • Cisco Systems CISCO1751 - page 25

    25 Cisco 1751 Voice-over-IP Quick Start Guide 78-11259-05 Configuring Voice-over-IP Note For these commands to take ef fect, you hav e to cycle the port b y using the shutdown and no shutdo wn commands. Note Configure th e PBX to pass all dual-tone multifrequenc y (DTMF) signals to the router . Config ure the East router similar to the We s t route ...

  • Cisco Systems CISCO1751 - page 26

    26 Cisco 1751 Voice-over-I P Quick Start Guide 78-11259-05 Configuring Voice-over-I P • Multilink Point-to Point Protocol (PPP) interleaving • Real-T ime T ransport Protocol (R TP) header compression Cisco IOS software provides many other tools fo r ensuring QoS, such as custom queu ing, priority queuing, and w eighted fair queuin g. For furthe ...

  • Cisco Systems CISCO1751 - page 27

    27 Cisco 1751 Voice-over-IP Quick Start Guide 78-11259-05 Configuring Voice-over-IP RSVP Resource Reserv ation Protocol (RSVP) enables routers to reserve enough bandwidth on an interface for reliable and quality perfo rmance. RSVP works well on PPP , HDLC, and similar serial line interfaces. It does not work well on multi-access LANs. Y ou should c ...

  • Cisco Systems CISCO1751 - page 28

    28 Cisco 1751 Voice-over-I P Quick Start Guide 78-11259-05 Configuring Voice-over-I P Configuring Multilink PPP Interleaving T o conf igure multilink PPP and interlea ving on a dial er, ISDN PRI or I SDN BRI interface, or a virtual template, you must fir st configure mu ltilink PPP and interl eaving on the in terf ace or template by entering the fo ...

  • Cisco Systems CISCO1751 - page 29

    29 Cisco 1751 Voice-over-IP Quick Start Guide 78-11259-05 Configuring Voice-over-IP Configuring Frame Relay for VoIP Config uring V oIP on a Frame Relay li nk in volv es ce rtain special considerati ons to ensure acceptable voi ce quality . For Frame Relay links with slo w output rates (64 kbps or l ess) and with data and voice being transmitted o ...

  • Cisco Systems CISCO1751 - page 30

    30 Cisco 1751 Voice-over-I P Quick Start Guide 78-11259-05 List of Terms List of Terms This section def ines some of the V oIP terms and co ncepts used in this guide. BRI —Basic Rate Interface, an ISDN interf ace. CIR —Committed information rate. The a verage rate of in formation tran sfer a subscriber (for example, the network administ rator) ...

  • Cisco Systems CISCO1751 - page 31

    31 Cisco 1751 Voice-over-IP Quick Start Guide 78-11259-05 Obtaining Documentation RT P —Real-Time T ransport Proto col, a network protocol used to carry audio and video packet traf f ic ov er an IP network. session target —A remote IP or DNS address specif ied for a dial peer . tag —A positiv e integ er in the range 1 to 2 31 -1 (21474836 47) ...

  • Cisco Systems CISCO1751 - page 32

    32 Cisco 1751 Voice-over-I P Quick Start Guide 78-11259-05 Documentation Fe edback Documentation Feedback Y ou can send comments about technical documentation to bug-doc@cisco.com. Y ou can submit comments by using the resp onse card (if present) behind the front co ver of your document or by writ ing to the follo wing address: Cisco Systems Attn: ...

  • Cisco Systems CISCO1751 - page 33

    33 Cisco 1751 Voice-over-IP Quick Start Guide 78-11259-05 Obtaining Additional Publ ications and Information T o open a service req uest by telephone, use one of the fo llowi ng numbers: Asia-Pacif ic: +61 2 8446 741 1 (Australia: 1 800 805 227) EMEA: +32 2 704 55 55 USA: 1 800 553 24 47 For a complete list of Cisco T AC contact s, go to this URL: ...

  • Cisco Systems CISCO1751 - page 34

    34 Cisco 1751 Voice-over-I P Quick Start Guide 78-11259-05 Obtaining Additional Pub lications and Information • iQ Magazine is the quarterly pub lication from Cisco Syst ems designed to help gro wing compan ies learn ho w they can use technology to in crease rev enue, streamline their b usiness, and expand services. The publication iden tifie s t ...

Fabbricante Cisco Systems Categoria Network Router

I documenti che otteniamo dal fabbricante del dispositivoCisco Systems CISCO1751 possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Cisco Systems
- manuali per l’uso CISCO1751
- schede prodotto Cisco Systems
- opuscoli
- o etichette energetiche Cisco Systems CISCO1751
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Cisco Systems CISCO1751.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Cisco Systems CISCO1751, manuali di manutenzione, brevi manuali o manuali utente Cisco Systems CISCO1751. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Cisco Systems CISCO1751.

Manuali per l’uso simili

Manuale completo del dispositivo Cisco Systems CISCO1751, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Cisco Systems CISCO1751 dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Cisco Systems CISCO1751.

Il manuale per l’uso completo Cisco Systems, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Cisco Systems CISCO1751 - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Cisco Systems CISCO1751, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Cisco Systems CISCO1751 che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Cisco Systems CISCO1751 - che ci dovrebbe aiutare nei primi passi durante l'uso Cisco Systems CISCO1751
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Cisco Systems CISCO1751
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Cisco Systems CISCO1751 in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Cisco Systems CISCO1751?

Utilizza il modulo sottostante

Se non hai risolto il problema con Cisco Systems CISCO1751 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Cisco Systems CISCO1751 è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)