Italiano dropdown-ico

Manuale per l’uso Berkel 919A

23 pagine 0.12 mb
Scarica

Vai alla pagina of 23

Summary
  • Berkel 919A - page 1

    909A & 919A O WNER /O PERATOR M ANUAL • 23 O WNER /O PERA T OR M ANUAL IMPORTANT NOTICE This manual contains Important Safety Instructions which must be strictly fol- lowed when using this equipment. NOTICIA IMPORTANTE Este manual contiene importantes instrucciones de seguridad que deben ser seguidas el pie de la letra cuando utilice esta maq ...

  • Berkel 919A - page 2

    22 • 909A & 919A O WNER /O PERATOR M ANUAL B EFORE U SING T HIS E QUIPMENT Berkel’ s slicers are designed to slice meat and other food products safely and efficiently . However , unless the operator is properly trained and supervised, there is the possibility of a serious injury . It is the responsi- bility of the owner to ensure that this ...

  • Berkel 919A - page 3

    909A & 919A O WNER /O PERATOR M ANUAL • 1 T ABLE OF C ONTENTS Page General Safety Instructions .................................................................................................... .............. 2 Equipment Description .......................................................................................................... .. ...

  • Berkel 919A - page 4

    2 • 909A & 919A O WNER /O PERATOR M ANUAL PELIGRO CUCHILLA FILOSA para evitar serios accidentes a su persona siga las instrucciones de este manual y 1. NUNCA utlice esta mçquina sin previa instrucciùn y autorizaciùn de su supervisor . 2. LA MçQUINA DEBE apoyarse sobre un nivel solido y plano. 3. LOS PROTECT ORES deben colocarse ANTES de e ...

  • Berkel 919A - page 5

    909A & 919A O WNER /O PERATOR M ANUAL • 3 W ARNING SHARP KNIFE BLADE to avoid serious personal injury follow all the instructions in this manual and 1. NEVER touch this machine without training and authorization by your supervisor . 2. MACHINE MUST BE on solid level support. 3. GUARDS MUST BE in place before plugging in and turning on machine ...

  • Berkel 919A - page 6

    4 • 909A & 919A O WNER /O PERATOR M ANUAL E QUIPMENT D ESCRIPTION Pusher Hooks Pusher Pusher Slide Bar Sharpener Center Plate Product T able Handle ...

  • Berkel 919A - page 7

    909A & 919A O WNER /O PERATOR M ANUAL • 5 E QUIPMENT D ESCRIPTION Product Table Gauge Plate Center Plate Locking Knob Slice Deflector ON/OFF Switch HI/LOW Switch Shift Lever Thickness Control Knob ...

  • Berkel 919A - page 8

    6 • 909A & 919A O WNER /O PERATOR M ANUAL I NST ALLA TION G ENERAL SAFE OPERATION REQUIRES PROPER INSTALLATION AND PROPER WORK AREA. 1. Slicer should be installed in an area having adequate lighting. 2. Operator should have adequate space to move freely in the work area. MACHINE MUST BE INSTALLED AND OPERATED ON SOLID, LEVEL SUPPORT. 3. Insta ...

  • Berkel 919A - page 9

    909A & 919A O WNER /O PERATOR M ANUAL • 7 2. T ip the slicer onto a thick pad of cloth. 3. Remove one of the short shipping legs and replace with one of the 4” legs. T ighten and install a rubber foot. CAUTION Never have more than one leg loose at a time. 4. Once one 4” leg is in place, proceed to install the other three legs, ONE A T A T ...

  • Berkel 919A - page 10

    8 • 909A & 919A O WNER /O PERATOR M ANUAL 4. USDA authorized Berkel oil is available in 2-oz (P/N 4675-00182), 16-oz (P/N 4675-00183) and one-gallon (P/N 4675-00184) containers. 5. To store the pusher at the top of the product table, simply pull the product pusher to the top of the table and allow the nylon button to fall behind the catch pla ...

  • Berkel 919A - page 11

    909A & 919A O WNER /O PERATOR M ANUAL • 9 M ANUAL O PERA TION Note: Make sure on the Model 919A slicers that the shift lever is in the manual position. 1. Turn the unit on by pushing the START switch up, then release so that it goes back to the middle position. The knife will start slowly, then speed up. W ARNING THE PRODUCT TABLE HANDLE IS T ...

  • Berkel 919A - page 12

    10 • 909A & 919A O WNER /O PERATOR M ANUAL THE SLICER WILL STOP WHEN SHIFTED FROM “LO” TO “HI” OR “HI” TO “LO” WHILE THE SLICER IS RUNNING. IT WILL BE NECESSARY TO RESTART THE SLICER WHEN SWITCHING BETWEEN SPEEDS. WHEN SHIFTING, THE KNIFE SPEED WILL INCREASE (OR DECREASE) AS WELL AS THE PRODUCT TABLE. O PERA TING I NSTRUCTIONS ...

  • Berkel 919A - page 13

    909A & 919A O WNER /O PERATOR M ANUAL • 11 T HICKNESS A DJUSTMENT Note: If the thickness knob is closed, then the slicer must be turned on before the thickness knob can be turned. 1. Thickness adjustment allows you to vary the thickness of the slices from paper thin to more than 3/4 of an inch. T o make thinner slices, turn the thicknss contr ...

  • Berkel 919A - page 14

    12 • 909A & 919A O WNER /O PERATOR M ANUAL W ARNING AFTER EACH USE OF THE SLICER, TURN THE THICKNESS CONTROL KNOB FULL RIGHT. THIS PLACES THE GAUGE PLATE IN THE CLOSED POSITION AND COVERS THE KNIFE EDGE. S HARPENER M AINTENANCE W ARNING SHARP KNIFE TO AVOID SERIOUS PERSONAL INJURY: 1. NEVER touch rotating knife. 2. Always TURN OFF slicer when ...

  • Berkel 919A - page 15

    909A & 919A O WNER /O PERATOR M ANUAL • 13 T O R EPLACE THE S HARPENING S TONES : 1. Remove the stones from the shaft by using a 10-millimeter metric wrench while gripping the stone firmly with the left hand. NOTE: The sharpening stone (cup shaped) is mounted on a left-hand threaded shaft. Turn the nut to the right to remove. The deburring st ...

  • Berkel 919A - page 16

    14 • 909A & 919A O WNER /O PERATOR M ANUAL D ISASSEMBL Y FOR C LEANING 1. Turn off and unplug the slicer from the wall outlet. 2. Slide product table toward you . 3. Turn the thickness control knob fully to the right. The gauge plate must be completely closed and the arm fully forward before the table can be removed. 4. Loosen the product tab ...

  • Berkel 919A - page 17

    909A & 919A O WNER /O PERATOR M ANUAL • 15 C LEANING THE K NIFE W ARNING THE KNIFE BLADE IS EXPOSED DURING THESE CLEANING STEPS. The stainless steel knife will corrode if not properly cleaned and maintained. To properly clean the knife: 1. Make sure thickness control knob is as far to the right as possible. 2. Clean front side of knife using ...

  • Berkel 919A - page 18

    16 • 909A & 919A O WNER /O PERATOR M ANUAL W ARNING TO PREVENT PRODUCT CONTAMINATION, USE ONLY USDA-AUTHORIZED OIL (P/N4975-00182). S ANITIZING 1. After cleaning, the slicer MUST BE SANITIZED to kill germs and bacteria . 2. Use only an APPROVED SANITIZING SOLUTION. 3. Sanitize slicer. Spray with sanitizing solution and air dry . S HARPENING G ...

  • Berkel 919A - page 19

    909A & 919A O WNER /O PERATOR M ANUAL • 17 7. Lift the sharpener with left hand and rotate into sharpening position and lower with ONE STONE on each side of the blade . 8. Place your left thumb on the sharpener cover for control, and pull the sharpening lever with your left index finger until it stops . 9. Turn slicer ON with right hand . Hol ...

  • Berkel 919A - page 20

    18 • 909A & 919A O WNER /O PERATOR M ANUAL T RA YS R ECEIVING T RAY (3875-00059) The receiving tray is a shallow-lipped tray to receive the product and hold small quantities of juices (hot beef, tomatoes, etc.) The tray is contour molded to the receiving area of the machine to hold it steady during operation. S LA W T RA Y (3875-00031) The sl ...

  • Berkel 919A - page 21

    909A & 919A O WNER /O PERATOR M ANUAL • 19 3. Inspect the power cord? Has it been damaged, cutting off electrical flow? 4. Are you getting electricity from wall outlet? Check by plugging in another piece of equipment with the same electrical requirements. Also, check the circuit breaker or fuse. If you are getting electrical power , and your ...

  • Berkel 919A - page 22

    20 • 909A & 919A O WNER /O PERATOR M ANUAL S PECIFICA TIONS D IAMETER OF K NIFE : 12 1 / 2 " (318 mm) S LICE T HICKNESS : up to 27/32" (21 mm) K NIFE S PEED : 400 rpm high/265 rpm low S LICING S PEED : 60 spm high/40 spm low (919A ONLY ) S LICING C AP ACITY : Square 11" x 6" (280 mm x 152 mm) Round 8" (203 mm) 919A 90 ...

  • Berkel 919A - page 23

    909A & 919A O WNER /O PERATOR M ANUAL • 21 W arranty Effective: February 14, 2002 Berkel Company (“Berkel”) warrants to the Buyer of new equipment that said equipment, when installed in accordance with our instructions and subjected to normal use, is free from defects in material or workmanship for a period of one (1) year from the date o ...

Fabbricante Berkel Categoria Kitchen Utensil

I documenti che otteniamo dal fabbricante del dispositivoBerkel 919A possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Berkel
- manuali per l’uso 919A
- schede prodotto Berkel
- opuscoli
- o etichette energetiche Berkel 919A
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Berkel 919A.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Berkel 919A, manuali di manutenzione, brevi manuali o manuali utente Berkel 919A. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Berkel 919A.

Manuali per l’uso simili

Manuale completo del dispositivo Berkel 919A, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Berkel 919A dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Berkel 919A.

Il manuale per l’uso completo Berkel, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Berkel 919A - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Berkel 919A, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Berkel 919A che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Berkel 919A - che ci dovrebbe aiutare nei primi passi durante l'uso Berkel 919A
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Berkel 919A
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Berkel 919A in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Berkel 919A?

Utilizza il modulo sottostante

Se non hai risolto il problema con Berkel 919A con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Berkel 919A è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)