-
Kingston Technology EtheRx KNE8TX/WG - page 1
KINGSTON TECHNOLOGY EtheRx 4-PORT AND 8-PORT WORKGROUP 100BASE-TX FAST ETHERNET HUBS USER’S GUIDE MODELS: KNE4TX/WG KNE8TX/WG ...
-
Kingston Technology EtheRx KNE8TX/WG - page 2
...
-
Kingston Technology EtheRx KNE8TX/WG - page 3
i KNExTX/WG User’s Guide - Rev. A00 Kingston Technology Company Kingston Technology’s EtheRx Workgroup 4-Port and 8-Port 100BASE-TX Fast Ethernet Hubs User’s Guide Part No. 4460057-001.A00 Kingston Technology Company 17600 New hope Fountain Valley, CA 92708 (714) 435-2600 ...
-
Kingston Technology EtheRx KNE8TX/WG - page 4
ii Kingston Technology Company KNExTX /WG User’s Guide - Rev. A00 T ABLE O F C ONTENTS Introducti on...................................................................................... 1 Model Ty pes...................................................................... 1 Special F eatures ........................................................ ...
-
Kingston Technology EtheRx KNE8TX/WG - page 5
iii KNExTX/WG User’s Guide - Rev. A00 Kingston Technology Company Appendix B Cab ling Guide lines .................................... 11 UTP Cable Wiring ............................................. 11 Cable Wiring Standards .................................... 11 Rating C odes .................................................... 13 Appendix C ...
-
Kingston Technology EtheRx KNE8TX/WG - page 6
...
-
Kingston Technology EtheRx KNE8TX/WG - page 7
Introduction 1 KNExTX/WG User’s Guide - Rev. A00 Kingston Technology Company Introduction Intended Audience: This manual assumes that th e user has a general working knowledge of networking principles a nd architecture and is familiar with network systems in general. Congratulations on the purchase of your Kingston EtheRx WorkGroup ( WG) series 1 ...
-
Kingston Technology EtheRx KNE8TX/WG - page 8
2 Introduction Kingston Technology Company KNExTX /WG User’s Guide - Rev. A00 Special Features • 100BASE-TX Class II compliant repeater • Conforms to IEEE802.3u 100BASE-TX standard • 4 or 8 UTP ports for 100BASE-TX connections • 4 or 8 Link, Activity, and Partition/Error status LEDs for easy troubleshooting • Utilization LEDs for displa ...
-
Kingston Technology EtheRx KNE8TX/WG - page 9
Design Features 3 KNExTX/WG User’s Guide - Rev. A00 Kingston Technology Company Design Features The EtheRx hub complies with the full se t of repeater basic functions as defined by IEEE 802.3u. These functions include all Repeater Functions, Signal Regeneration, Receive Jabber Pr otection, Collision-Handling, Error- Handling, and Auto Partitionin ...
-
Kingston Technology EtheRx KNE8TX/WG - page 10
4 Front Panel Kingston Technology Company KNExTX /WG User’s Guide - Rev. A00 Hardware Installation Before you begin installing network cab les, please take a few moments to familiarize yourself with the EtheRx hubs . The front and rear panels of the Fast Ethernet Workgroup hubs are illustrated below. Front Panel Fig. 1-2 KNE4TX/WG Front Panel Fig ...
-
Kingston Technology EtheRx KNE8TX/WG - page 11
Front Panel 5 KNExTX/WG User’s Guide - Rev. A00 Kingston Technology Company Utilization LEDs The five Utilization LEDs display the rate of network traffic in percentages of the total available bandwidth. The amount of data traffic is measured in frames per second (FPS), then calculated into percentage values: 1%, 12%, 25%, 50%, and > 60%. The ...
-
Kingston Technology EtheRx KNE8TX/WG - page 12
6 Front Panel Kingston Technology Company KNExTX /WG User’s Guide - Rev. A00 Cascade Switch The Cascade Switch provides cable wiring flexibility on the last UTP Port (i.e., Port 4 or Port 8) for connecting to a workstation or cascading to another hub. By default, the last UTP port is set to “Crossover” (left side) as a standard, internally-cr ...
-
Kingston Technology EtheRx KNE8TX/WG - page 13
Front Panel 7 KNExTX/WG User’s Guide - Rev. A00 Kingston Technology Company Port 1 through Port 3 (or 7) respectively, like all normal hub ports, are configured MDI-X, whereas the last UTP ports, Port 4 or Port 8, support both port configurations, MDI and MDI-X. All NICs (Network Interface Cards) and Router ports are usually by default c onfigure ...
-
Kingston Technology EtheRx KNE8TX/WG - page 14
8 Rear Panel Kingston Technology Company KNExTX /WG User’s Guide - Rev. A00 Rear Panel Fig. 1-6 KNE4TX/WG Rear Panel Fig. 1-7 KNE8TX/WG Rear Panel 4 or 8 UTP Ports The UTP ports are numbered 1 through 4 or 1 through 8 for 100BASE-TX connections. Since crossover functi on is implemented on all UTP MDI-X ports, a straight-through UTP cable should b ...
-
Kingston Technology EtheRx KNE8TX/WG - page 15
Appendices 9 KNExTX/WG User’s Guide - Rev. A00 Kingston Technology Company Appendices ...
-
Kingston Technology EtheRx KNE8TX/WG - page 16
10 Appendix A Pin Assignments Kingston Technology Company KNExTX /WG User’s Guide - Rev. A00 Appendix A Pin Assignments UTP Pin Assignments UTP Ports use RJ-45 Unshielded Twis ted Pair (UTP) cabling. Cable Pin Numbers and Pin Wiring Assignments are listed below in Figure A-1 and Table A-2, respectively. Twisted-Pair cable s can be wired with eith ...
-
Kingston Technology EtheRx KNE8TX/WG - page 17
Appendix B Cabling Guidelines 11 KNExTX/WG User’s Guide - Rev. A00 Kingston Technology Company Appendix B Cabling Guidelines UTP Cable Wiring 100BASE-TX unshielded twisted-pair cables can be wired as "Straight- Through" or, in some cases, "Crossover" depending on the application. For workstations connected to a hub, use " ...
-
Kingston Technology EtheRx KNE8TX/WG - page 18
12 Appendix B Cabling Guidelines Kingston Technology Company KNExTX /WG User’s Guide - Rev. A00 1 2 3 4 5 6 7 8 Pair 2 Pair 3 Pair 1 Pair 4 T568A Fig. B-1 4-Pair T568A Wiring 1 2 3 4 5 6 7 8 Pair 3 Pair 2 Pair 1 Pair 4 T568B Fig. B-2 4-Pair T568B Wiring T568A Pairs Strand Solid T568B Pairs Strand Solid Pin 1 Pair 3 Blue W hite/Green Pin 1 Pair 2 ...
-
Kingston Technology EtheRx KNE8TX/WG - page 19
Appendix B Cabling Guidelines 13 KNExTX/WG User’s Guide - Rev. A00 Kingston Technology Company Rating Codes UTP cables meet different UL-NEC requirements based on cable-jacket quality. Below is an explanation of the rating codes for each cable type. UL – The National Electrical Code (NEC ), published by the National Fire Protection Association ...
-
Kingston Technology EtheRx KNE8TX/WG - page 20
14 Appendix B Cabling Guidelines Kingston Technology Company KNExTX /WG User’s Guide - Rev. A00 4. NEAR - END CROSSTALK (NEXT) – In wires packed together within a cable, the signals generated at one end of the link can flush out the weaker signals coming back from the recipient. Appendix C Specifications EtheRx 4- and 8-Port Fas t Ethernet Work ...
-
Kingston Technology EtheRx KNE8TX/WG - page 21
Appendix D Commonl y Asked Questions 15 KNExTX/WG User’s Guide - Rev. A00 Kingston Technology Company EMI Standards: FCC Class A, CE CISPR A EMC Standards: EN 55022, IEC801-2, IEC801-3, IEC801-4 Low Voltage Directive: EN60950 ...
-
Kingston Technology EtheRx KNE8TX/WG - page 22
16 Appendix D Comm only Asked Questions Kingston Technology Company KNExTX /WG User’s Guide - Rev. A00 Appendix D Commonly Asked Questions Class I vs. Class II 100BASE-TX Fast Ethernet Repeaters There are currently two classes of Fast Ethernet repeaters, defined as Class I and Class II . Class I : in a maximum length segment topology, only one Cl ...
-
Kingston Technology EtheRx KNE8TX/WG - page 23
Appendix D Commonl y Asked Questions 17 KNExTX/WG User’s Guide - Rev. A00 Kingston Technology Company Category 5 Compliance v s. Category 5 Performance? Having CAT 5 components in your netw ork installation does not necessarily achieve full Category 5 performance. To achieve any category-rated performance, make sure all cabling com ponents are at ...
-
Kingston Technology EtheRx KNE8TX/WG - page 24
18 Appendix D Mounting Templates Kingston Technology Company KNExTX /WG User’s Guide - Rev. A00 The EtheRx WorkGroup hubs can be stationed on a flat surface using the four rubber feet provided, or mounted vertically by using the mounting holes on the bottom side of the unit. The illustrati ons below detail the measurem ents and mounting holes and ...
-
Kingston Technology EtheRx KNE8TX/WG - page 25
Appendix F Warranties and Notices 19 KNExTX/WG User’s Guide - Rev. A00 Kingston Technology Company Appendix F Warranties and Notices Limited Warranty Statement KINGSTON TECHNOLOGY COMPANY ("Kingston") warrants that this product is free from defects in m aterial and workm anship. Subject to the conditions and limitations set forth below, ...
-
Kingston Technology EtheRx KNE8TX/WG - page 26
20 Appendix F Warranties and Notices Kingston Technology Company KNExTX /WG User’s Guide - Rev. A00 Warranty Claim Requirements To obtain warranty service, return the defec tive product, freight prepaid and insured, to your local authorized Kingston dealer or di stributor, or to the Kingston factory service center located at 17600 Newhope Street, ...
-
Kingston Technology EtheRx KNE8TX/WG - page 27
Appendix F Warranties and Notices 19 KNExTX/WG User’s Guide - Rev. A00 Kingston Technology Company F.C.C. Certification This device has been tested and found to comply with limits for Class A digital device, pursuant to Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interferen ...
Hai una domanda su Kingston Technology EtheRx KNE8TX/WG?
Utilizza il modulo sottostante
Se non hai risolto il problema con Kingston Technology EtheRx KNE8TX/WG con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Kingston Technology EtheRx KNE8TX/WG è probabile che voglia condividere il modo di risolverlo.