Italiano dropdown-ico

Manuale per l’uso Billy Goat BC2403

28 pagine 1.87 mb
Scarica

Vai alla pagina of 28

Summary
  • Billy Goat BC2403 - page 1

    Part No 500402 1 Form No F020513A BILLY GOAT ® BC2403 Series Brush Cutter Owner’s Manual Patent Number D386768 ...

  • Billy Goat BC2403 - page 2

    Part No 500402 2 F0 20513A BC2403 Series Brush Cutter Owner’s Manual CONTENTS Specifications and Sound/Vibration .................................................................................................................. 3 Instruction Labels ................................................................................................... ...

  • Billy Goat BC2403 - page 3

    Part No 500402 3 F0 20513A BC2403 Series Brush Cutter Owner’s Manual BC 2403 SERIES SPECIFICATIONS BC2403IC BC2403ICF BC2403HF BC2403H BC2403HEB Engine Type Briggs and Stratton INTEK OHV Briggs and Stratton INTEK OHV Honda GXV Honda GXV Honda GXV Model Number 21A902-0149- E1 21A902-0149- E1 GXV390UTIDABG GXV390UTIDABG GXV390K1DE33 Horsepower 13.0 ...

  • Billy Goat BC2403 - page 4

    Part No 500402 4 F0 20513A BC2403 Series Brush Cutter Owner’s Manual INSTRUCTION LABELS The labels shown below were installed on your BILLY GOAT ® Brush Cu tter. If any labels are damaged or mi ssing, replace them before operating this equip ment. Item numbers from the Illustrated Parts List and part numbers are provided for convenience in order ...

  • Billy Goat BC2403 - page 5

    Part No 500402 5 F0 20513A BC2403 Series Brush Cutter Owner’s Manual Brush Cutter Assembly Drawin g Figure 1 100 22 Attach shifter to linkage here 202 ...

  • Billy Goat BC2403 - page 6

    Part No 500402 6 F0 20513A BC2403 Series Brush Cutter Owner’s Manual ASSEMBLY INSTRUCTIONS Your BIL LY G OAT ® BC S elf -Propelled Brush Cutter was shipped in one carton, completely assembled except for the upper handle assembly an d the front guard bar. Mounting hardware for the handle and guard bar is temporarily installed on the lower handle ...

  • Billy Goat BC2403 - page 7

    Part No 500402 7 F0 20513A BC2403 Series Brush Cutter Owner’s Manual OPERATION O PERATOR C ONTROLS The operator’s station is at the rear of the machine between the handlebars. The operator should STAND in a position to allow both handlebars to be grasped firmly and which allows sufficient leverage to steer the machine. Operator’s controls are ...

  • Billy Goat BC2403 - page 8

    Part No 500402 8 F0 20513A BC2403 Series Brush Cutter Owner’s Manual 4. Units equipped with electric starters: Pull up on the ON/OFF switch until engine starts. ON/OFF (I/O) (Manual start shown) DO NOT START equipment with drive or blade clutch engaged. 5. Units equipped with manual starters: Pull starter rope to start engine. PULL STARTER CORD s ...

  • Billy Goat BC2403 - page 9

    Part No 500402 9 F0 20513A BC2403 Series Brush Cutter Owner’s Manual 2. Press blade clutch handle down to engage blade. Allow blade to spin up to normal operating speed. Blade Clutch Lever 3. Pull drive clutch handle up to engage transaxle. Drive Clutch Lever S HUT D OWN 1. Release drive clutch handle to disengage transaxle. 2. Release blade clut ...

  • Billy Goat BC2403 - page 10

    Part No 500402 10 F0 20513A BC2403 Series Brush Cutter Owner’s Manual MAINTENANCE P ERIODIC M AINTENANCE Periodic maintenance should be perfo rmed at the following intervals: Maintenance Operation Every Use Daily or Every 5 Hours Every 25 Hours Every 50 Hours Every 100- 150 Hours Inspect for worn or damaged parts .  Check for excessive vibrati ...

  • Billy Goat BC2403 - page 11

    Part No 500402 11 F0 20513A BC2403 Series Brush Cutter Owner’s Manual B LADE R EMOVAL AND S HARPENING READ all safety instructions before servicing unit. Numbers in parenthesis (N) refers to the item number in Illustrated Parts List. Tools required: - 5/8” socket, 1/2” drive - T orque wrench, 1/2” drive - Jack stands or similar device adequ ...

  • Billy Goat BC2403 - page 12

    Part No 500402 12 F0 20513A BC2403 Series Brush Cutter Owner’s Manual B LADE D RIVE B ELT T ENSION A DJU STMENT READ all safety instructions before servicing unit. DISCONNECT spark plug wire before servicing unit. Numbers in parenthesis (N) refers to the item number in Illustrated Parts List. 1. Disconnect spark plug wire. 2. Remove two screws ho ...

  • Billy Goat BC2403 - page 13

    Part No 500402 13 F0 20513A BC2403 Series Brush Cutter Owner’s Manual B LADE C LUTCH A DJUSTMENT READ all safety instructions before servicing unit. DISCONNECT spark plug wire before servicing unit. 1. Disconnect spark plug wire. 2. As the clutch/brake wears or begins slipping or squealing, adjustment may be required to maintain proper cable tens ...

  • Billy Goat BC2403 - page 14

    Part No 500402 14 F0 20513A BC2403 Series Brush Cutter Owner’s Manual B LADE D RIVE B ELT R EMOVAL AND R EPLACEMENT READ all safety instructions before servicing unit. Numbers in parenthesis (N) refers to the item number in Illustrated Parts List. Tools required: - 1/2” socket, 3/8” drive - ratchet, 3/8” - drive extension, 3/8” drive - un ...

  • Billy Goat BC2403 - page 15

    Part No 500402 15 F0 20513A BC2403 Series Brush Cutter Owner’s Manual 12. Tighten four screws (103) to secure belt guides (149, 150). Make sure belt is correctly routed. (See Figure below ). 13. Adjust blade drive belt tension by reaching in through top of engine base with pry bar or long screwdriver and pushing idler pulley against belt to incre ...

  • Billy Goat BC2403 - page 16

    Part No 500402 16 F0 20513A BC2403 Series Brush Cutter Owner’s Manual T RANSAXLE D RIVE C LUTCH A DJUS TMENT READ all safety instructions before servicing unit. DISCONNECT spark plug wire before servicing unit. 1. Disconnect spark plug wire. 2. As the belt wears or begins slipping or squealing, adjustment may be required to maintain proper cable ...

  • Billy Goat BC2403 - page 17

    Part No 500402 17 F0 20513A BC2403 Series Brush Cutter Owner’s Manual T RANSAXLE D RIVE B ELT R EMOVAL AND R EPLACEMENT READ all safety instructions before servicing unit. Numbers in parenthesis (N ) refers to the item number in Illustrated Parts List. Tools required: ½” socket and ratchet, ½” universal extension bar, pry bar or long screwd ...

  • Billy Goat BC2403 - page 18

    Part No 500402 18 F0 20513A BC2403 Series Brush Cutter Owner’s Manual W IRING D IAGRAMS Starter Switch Wiring Figure 3 Starter Circuit Schematic Diagra m Figure 4 ON/OFF Switch Circuit Schematic Diagram Figure 5 SWITCH WHITE RED + - STARTER SOLENOID BATTERY BLACK 20A FUSE RED STARTER MOTOR ENGINE GROUND RED BLACK M A1 B MAGNETO ENGINE GROUND ON/O ...

  • Billy Goat BC2403 - page 19

    Part No 500402 19 F0 20513A BC2403 Series Brush Cutter Owner’s Manual TROUBLESHOOTING Problem Possible Cause Corrective Action Engine will not start. ON/OFF switch is in OFF position. Move switch to START position. Out of gasoline. Fill gas tank. Old or contaminated gasoline. Drain gas tank and fill with fresh gas oline. Spark plug wire disconnec ...

  • Billy Goat BC2403 - page 20

    Part No 500402 20 F0 20513A BC2403 Series Brush Cutter Owner’s Manual Battery Care (For Electric -Starting Models) Proper care can extend the life o f a battery. Follow these recommendations to ens ure your battery’s best performance and long life: • Do not allow the battery charge to get too low. If the machine is not used, ch arge the batte ...

  • Billy Goat BC2403 - page 21

    Part No 500402 21 F0 20513A BC2403 Series Brush Cutter Owner’s Manual ILLUSTRATED PARTS LIST Engine and Engine Base A ssembly Figure 6 ...

  • Billy Goat BC2403 - page 22

    Part No 500402 22 F0 20513A BC2403 Series Brush Cutter Owner’s Manual ITEM NO DESCRIPTION BC2403 HEB BC2403H BC2403IC Part No QTY Part No QTY Part No QTY 4 Base Assembly with label s 500240 1 500240 1 500240 1 7 Door Base Engine 500233 1 500233 1 500233 1 22 Tube Shift With Grip 500404 1 500404 1 500404 1 23 Clutch Brake 500338 1 500338 1 500338 ...

  • Billy Goat BC2403 - page 23

    Part No 500402 23 F0 20513A BC2403 Series Brush Cutter Owner’s Manual Handlebar Assembly Figure 7 ...

  • Billy Goat BC2403 - page 24

    Part No 500402 24 F0 20513A BC2403 Series Brush Cutter Owner’s Manual ITEM NO DESCRIPTION BC2403HEB BC2403H BC2403IC Part No QTY Part No QTY Part No QTY 5 Handle Brace Left 500196 1 500196 1 500196 1 6 Handle Brace Right 500200 1 500200 1 500200 1 17 Cable Clutch Blade BC2402 500259 1 500259 1 500259 1 18 Cable Clutch Drive BC2402 500327 1 500327 ...

  • Billy Goat BC2403 - page 25

    Part No 500402 25 F0 20513A BC2403 Series Brush Cutter Owner’s Manual Transaxle and Blade Deck Assembly Figure 8 ...

  • Billy Goat BC2403 - page 26

    Part No 500402 26 F0 20513A BC2403 Series Brush Cutter Owner’s Manual ITEM NO DESCRIPTION BC2403HEB BC2403H BC2403IC Part No QTY Part No QTY Part No QTY 1 Deck Assembly with Label s 500407 1 500407 1 500407 1 3 Deflector Front BC2402 500125 1 500125 1 500125 1 8 Transaxle 3 SPD BC2402 500365 1 500365 1 500365 1 9 Pulley 5.0" OD ‘A’ Secti ...

  • Billy Goat BC2403 - page 27

    Part No 500402 27 F0 20513A BC2403 Series Brush Cutter Owner’s Manual Blade Drive Spindle Assem bly Detail Drawing Figure 9 ...

  • Billy Goat BC2403 - page 28

    Part No 500402 28 F0 20513A BC2403 Series Brush Cutter Owner’s Manual ITEM NO DESCRIPTION BC2403HEB BC2403H BC 2403IC Part No QTY Part No QTY Part No QTY 134 Spindle Assembly Complete 500242 1 500242 1 500242 1 30 Spacer Spindle BC2402 500232 1 500232 1 500232 1 34 Spindle WA BC2402 500174 1 500174 1 500174 1 35 Bearing 7/8" ID Sealed Press ...

Fabbricante Billy Goat Categoria Brush Cutter

I documenti che otteniamo dal fabbricante del dispositivoBilly Goat BC2403 possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Billy Goat
- manuali per l’uso BC2403
- schede prodotto Billy Goat
- opuscoli
- o etichette energetiche Billy Goat BC2403
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Billy Goat BC2403.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Billy Goat BC2403, manuali di manutenzione, brevi manuali o manuali utente Billy Goat BC2403. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Billy Goat BC2403.

Manuali per l’uso simili

Manuale completo del dispositivo Billy Goat BC2403, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Billy Goat BC2403 dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Billy Goat BC2403.

Il manuale per l’uso completo Billy Goat, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Billy Goat BC2403 - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Billy Goat BC2403, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Billy Goat BC2403 che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Billy Goat BC2403 - che ci dovrebbe aiutare nei primi passi durante l'uso Billy Goat BC2403
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Billy Goat BC2403
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Billy Goat BC2403 in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Billy Goat BC2403?

Utilizza il modulo sottostante

Se non hai risolto il problema con Billy Goat BC2403 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Billy Goat BC2403 è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)