Italiano dropdown-ico

Manuale per l’uso Genie GPS-IC

32 pagine 1.3 mb
Scarica

Vai alla pagina of 32

Summary
  • Genie GPS-IC - page 1

    Au t o mat i c Cha i n D riv e/ Be lt D rive Ga ra ge Door O p er a t or S yst e m Owner ’ s Manual SA VE FOR FUTURE REFERENCE Customer Ser vice CALL: 1-800-354-3643 VISIT : WWW .GENIECOMP ANY .com 3507535556 GPS- IC Series PMX- IC B Series AUTOMA TIC GARAGE DOOR OPERA TOR SYSTEMS HANG MANUAL NEAR YOUR W ALL CONTROL Complete with Remote Control a ...

  • Genie GPS-IC - page 2

    Things to consider if you are planning to “ do-it-yourself. ” Whether you are replacing an existing garage door operator or installing an operator in your garage for the first time, there are some pre-installation issues which need to be addressed. They are as follows: The Genie Company recommends that you read and fully understand all informat ...

  • Genie GPS-IC - page 3

    3 TYPICAL SECTIONAL DOOR INST ALLA TION 5 TYPICAL SUPPORT BRACKET EXTENSION SPRING OR T ORSION SPRING SAFE-T -BEAM ® BRACES ADDED HEADER BRACKET MOUNTING BOARD 36 ” POWER CORD TO 120V GROUNDED OUTLET 6 4 3 1 2 3 TYPICAL (TRACK GUIDED) 1-PIECE DOOR INST ALLA TION 7 SECTIONAL DOOR ONE-PIECE DOOR TYPICAL (TRACKLESS) 1-PIECE DOOR INST ALLA TION ...

  • Genie GPS-IC - page 4

    4 W ARNING : Garage doors are large, heavy objects that move with the help of springs under high tension and electric motors. Since moving objects, springs under tension, and electric motors can cause injuries, your safety and the safety of others depend on you reading the information in this manual. If you have questions or do not understand the i ...

  • Genie GPS-IC - page 5

    NOTE: Accessories vary by model . F ASTENERS - Shown full size. See Parts List for description. 10 5 10 4 103 101 10 6 12 6 12 4 12 5 Lag Screw , 1/4 ” x 2 ” Cotter Pin Clevis Pin Bolt, 3/8 ” -16 x 7/8 ” Phillips Hex Head Screw , No. 10 x 1-1/4 ” Insulated Staple Bolt, 5/16 ” -18 x 1/2 ” 10 0 69 11 2 79 81 82 12 7 N/A N/A 96 91 92 90 ...

  • Genie GPS-IC - page 6

    Stealth Power Head 2 3 4 5 6 7 8 9 10 1 12 13 14 15 16 17 18 19 20 11 22 23 24 25 26 27 28 29 30 21 32 33 34 35 36 37 38 39 31 40 12 12 12 12 11 19 3 12 26 26 Item Part Name 1 Lens 2F ront Cover 3S ide Cover (by series/model) 4T op Plate Assembly 5S t rain Relief 6C ord & Plug Assembly 7C omponent Panel (by series/model) 8 Bottom Cover 9S crew ...

  • Genie GPS-IC - page 7

    7 PA R TS IDENTIFICA TION FOR HELP-1.800.354.3643 OR GENIECOMP ANY .COM Item Part Name 61 Main Drive Worm 62 Screw , #8 x 3-1/8 ” Slot HH, Sf T ap 63 Limit Switch Plate 64 Screw , #6 x 3/8 ” Phillips w/Wshr , Sf T ap 65 Screw , #4 x 5/8 ” , Slot HH w/Wshr , Sf T ap 2 10 12 46 12 12 3 12 45 47 5 6 7 12 48 12 11 12 40 39 37 4 52 64 3 12 65 28 6 ...

  • Genie GPS-IC - page 8

    Channel Item Part Name 66 Belt & Bullet Assembly - 7 ’ 6 ” Door (Belt Models Only) Belt & Bullet Assembly - 8 ’ Door (Belt Models Only) Belt & Bullet Assembly - 10 ’ Door (Belt Models Only) Belt & Bullet Assembly - 12 ’ Door (Belt Models Only) 67 Sprocket Bushing 68 Sprocket, 10 T ooth - 7 ’ 6 ” & 8 ’ Doors (Chai ...

  • Genie GPS-IC - page 9

    9 Rail PA R TS IDENTIFICA TION FOR HELP-1.800.354.3643 OR GENIECOMP ANY .COM Item Part Name 102 Boom Support Kit (not shown) 103 Safety & Maintenance Guide 104 Emergency Release T ag (Tri-L) 105 Entrapment W ARNING Label 106 Wire 11 0 R a il (L=1 12.475 ” ) 111 S c r e w, 5/16 ” -18 x 3/4 ” 11 2 S crew , 5/16 ” x 1/2 ” HH w/Wshr 11 3P ...

  • Genie GPS-IC - page 10

    Fig. 1-3 No. 10-24 x 1/2 ” Hex Head Screws 5/16 ” x 1/2 ” Hex Head Screws “ D ” -Shaft and Hole 3. Place power head and channel on clean, flat surface. 4. Slide drive end of channel down over “ D ” -shaft on top of power head (Fig. 1-2). • Support header end of channel level with power head. • Slide carriage to align “ D ” -sh ...

  • Genie GPS-IC - page 11

    Fig. 1-4 Adjusting Bolt WHA T TYPE OF DOOR DO YOU HA VE? Look at the drawings below . They tell you where to find the installation instructions you need T rack Guided Doors SEE SECTION 2A T rackless Doors SEE SECTION 2 B. Section Door With Curved T rack Hardware 1-Piece Door With Horizontal T rack Hardware Curved Tr ack with V ertical Section Strai ...

  • Genie GPS-IC - page 12

    W ARNING • Do Not try to remove, repair or adjust springs or anything to which door spring parts are fastened, such as, wood blocks, steel brackets, cables or other like items. Repairs and adjustments must be made by a trained service person using proper tools and instructions. • Handles and other door projections can catch clothing. Remove rop ...

  • Genie GPS-IC - page 13

    CAUTION CAUTION Fig. 2-5 Mounting bracket must be fastened to garage framing. Do Not fasten to drywall, particle board, plaster or other such materials. Power Head Channel/Rail Assembly 6. Mount power head (See Section 2 MOUNTING METHODS). • Be sure channel/rail assembly and power head are on door center line (Line “ V ” ). • Check the illu ...

  • Genie GPS-IC - page 14

    8. Install door bracket (Fig. 2-6). • Contact door manufacturer . NOTE: Self-drilling screws are intended for use with light-weight door only , while lag screws are meant for wood doors only . Because door designs vary , modifications may be required and additional materials needed. Please contact your door manufacturer with any questions concern ...

  • Genie GPS-IC - page 15

    CAUTION W ARNING Header bracket must be fastened to garage framing. Do Not fasten to drywall, particle board, plaster or other such materials. 1. Establish center line of door and header (Fig. 2-9). • Close door . • Measure door width. Mark center . • Use straight edge to draw vertical line “ V. ” – down door about 6. ” – on top of ...

  • Genie GPS-IC - page 16

    CAUTION 6. Install door bracket (Fig. 2-12). • Contact door manufacturer for proper installation. NOTE: Self-drilling screws are intended for use with light-weight door only , while lag screws are meant for wood doors only . Because door designs vary , modifications may be required and additional materials needed. Please contact your door manufac ...

  • Genie GPS-IC - page 17

    CAUTION Mounting bracket must be fastened to garage framing. Do Not fasten to drywall, particle board, plaster or other such materials. 9. Mount power head (See Section 2 AL TERNA TE MOUNTING METHODS). • Be sure rail assembly and power head are on door center line (line “ V ” ). • Check the illustrations. Decide which mounting method you wi ...

  • Genie GPS-IC - page 18

    NOTE: Mounting brackets can be attached to the floor using concrete anchors (not provided). 2. Mounting STB source and sensor . • If garage has only one garage door . – Determine which side of garage receives most direct sunlight (Fig. 3-4) . – Red LED should always be on sunny side whenever possible (Fig. 3-4) . • For multiple doors. – P ...

  • Genie GPS-IC - page 19

    CAUTION FIG. 3-8 (ProMax) Attachments at power head . • Make wire attachments at STB ’ s. – Splitting and stripping wire ends to be connected as shown (Fig. 3-6) . – Loosen terminal screws. – Insert wire under flat plate and tighten screw . It does not matter which wire, white or striped, goes on which terminal (Fig. 3-7) . • Make wire ...

  • Genie GPS-IC - page 20

    CAUTION W ARNING W all console W all button OR Fig. 4-2 #6 x 1 ” pan head screws Fig. 4-3 MORE T MENT OPEN PUSH LIMITS TO SET G4 Y3 B2 W1 1. Run wire from power head to wall control. • Place the wall control: – In sight of door . – At least 5 feet from floor , so small children can not reach it. – A way from moving parts of door and door ...

  • Genie GPS-IC - page 21

    1. Disconnect the power cord from the branch circuit mains. 2. Remove bottom cover from power head. • Remove four (4) hex head screws from front and rear covers. • Slide bottom cover off. 3. Remove existing power cord from power head. • Disconnect three power cord wires. • Remove and discard power cord. • Remove 7/8 ” diameter knock-out ...

  • Genie GPS-IC - page 22

    W ARNING Fig. 6-1 MORE MORE LIMIT ADJUSTMENT CLOSE OPEN PUSH LIMITS TO SET 4 3 2 1 CLASS 2 NEC OPEN CLOSE TO SET LIMITS PUSH OR NEC CLASS 2 1 2 3 4 5 6 MORE FORCE PUSH BUTTON SAFETY BEAM LIMIT SET OPEN FORCE CLOSE FORCE RADIO SIGNAL LEARN CODE COM DO NOT PUSH LIMIT SET UNLESS DOOR IS ATTACHED NOTE: USE ONLY WITH SERIES II CONTROLS CLOSE MORE OPEN M ...

  • Genie GPS-IC - page 23

    NEC CLASS 2 1 2 3 4 5 6 MORE FORCE PUSH BUTTON SAFETY BEAM LIMIT SET OPEN FORCE CLOSE FORCE RADIO SIGNAL LEARN CODE COM DO NOT PUSH LIMIT SET UNLESS DOOR IS ATTACHED NOTE: USE ONLY WITH SERIES II CONTROLS CLOSE MORE OPEN MORE CLOSE OPEN LIMIT ADJUSTMENT U.S. Patent No. 5,243,784 5,221,869 W ARNING CONT ACT REVERSE Fine adjustments for limit switche ...

  • Genie GPS-IC - page 24

    W ARNING During the following steps, the motor protector may open. W ait about 20 minutes for protector to reset. 1. Adjusting the “ OPEN ” limit switch (Fig. 8-1). • Run door to open position by pushing wall control. • Locate curved “ OPEN ” limit adjustment slot on back of power head. • Look into slot for pinion screw . • Insert a ...

  • Genie GPS-IC - page 25

    1. T urn remote control upside down (Fig. 10-1) 2. Battery replacement (your remote control is battery powered). • Gently push straight IN on tab as shown (Fig. 10-1). – use ball point pen, coin or small screwdriver . – battery cover snaps open. • Install new battery in same position. – use A23, 12 V olt battery . 3. Attach visor clip to ...

  • Genie GPS-IC - page 26

    1. Install light bulb(s) into socket(s). Do Not use short neck bulb(s). • Use bulb(s) rated for: – rough service. – vibration. – appliances. • 1 00 watt maximum. 2. Bend two (2) slotted tabs up. This will activate the ” living hinge ” of the lens (Fig. 1 1-1). NOTE: The following steps use the screws from the Blue Parts Bag that were ...

  • Genie GPS-IC - page 27

    MONTHL Y MAINTENANCE DOOR SPRINGS and DOOR HARDW ARE • Do not operate garage door automatically or manually if springs are broken. CONT ACT A PROFESSIONAL FOR SERVICE. • Oil door rollers, bearings, and hinges monthly . Use silicone lubricant or light oil. DOOR BALANCE • Close door . Pull red emergency release knob down and toward power head t ...

  • Genie GPS-IC - page 28

    CAUTION Door starts for no reason. Check staples on wire from power head to wall control. If they cut into insulation, they can short wires. If wire is cut, replace it. W as a remote control lost or stolen? Erase all remote control codes from receiver memory and reprogram. W all control button sticking. Check operation of buttons. Door starts down, ...

  • Genie GPS-IC - page 29

    CAUTION ( Stealth Motor ) Openin g cover could cause electrical shock. WIRING DIAGRAM FOR HELP-1.800.354.3643 OR GENIECOMP ANY .COM 29 ( ProMax Motor ) ...

  • Genie GPS-IC - page 30

    30 No C.O .D . shipments. Please include check or money order , made pay able to The Genie Company . Do not send cash .A llow 3-4 weeks f or delivery . 1-800-354-3643. Please have part number and credit card ready . Mail Order Form to: Genie Company , Alliance, Ohio 44601 .W e accept Visa or Mastercard on phone orders only . Please add local sales ...

  • Genie GPS-IC - page 31

    INST ALLA TION NOTES FOR HELP-1.800.354.3643 OR GENIECOMP ANY .COM CONT ACT NUMBERS NAME COMP ANY NUMBER NAME COMP ANY NUMBER NAME COMP ANY NUMBER NAME COMP ANY NUMBER NAME COMP ANY NUMBER NAME COMP ANY NUMBER 31 ...

  • Genie GPS-IC - page 32

    SA VE THESE INSTRUCTIONS Manufactured under one or more of the following U.S. patents: 3,898,582 / 4,041,259 / 4,048,630 / 4,064,487 / 4,103,238 / 5,222,403 Other Patents applied for 22790 Lake Park Blvd. • Alliance, Ohio USA • 44601 Customer Service 1. 800 .35 GENIE CORRESPONDENCE WITH F ACT ORY MUST INCLUDE DA TE / MFG. NO. ( LOCA TED UNDER L ...

Fabbricante Genie Categoria Garage Door Opener

I documenti che otteniamo dal fabbricante del dispositivoGenie GPS-IC possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Genie
- manuali per l’uso GPS-IC
- schede prodotto Genie
- opuscoli
- o etichette energetiche Genie GPS-IC
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Genie GPS-IC.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Genie GPS-IC, manuali di manutenzione, brevi manuali o manuali utente Genie GPS-IC. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Genie GPS-IC.

Manuali per l’uso simili

Manuale completo del dispositivo Genie GPS-IC, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Genie GPS-IC dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Genie GPS-IC.

Il manuale per l’uso completo Genie, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Genie GPS-IC - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Genie GPS-IC, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Genie GPS-IC che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Genie GPS-IC - che ci dovrebbe aiutare nei primi passi durante l'uso Genie GPS-IC
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Genie GPS-IC
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Genie GPS-IC in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Genie GPS-IC?

Utilizza il modulo sottostante

Se non hai risolto il problema con Genie GPS-IC con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Genie GPS-IC è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)