Italiano dropdown-ico

Manuale per l’uso Lowrance electronic 200

32 pagine 1.4 mb
Scarica

Vai alla pagina of 32

Summary
  • Lowrance electronic 200 - page 1

    www.lowrance.com Radar & RIM 200 Radar Interface Module Installation Instructions Pub. 988-0161-042 ...

  • Lowrance electronic 200 - page 2

    Copyright © 2007 Lowrance Electronics, Inc. All rights reserved. No part of this manual may be copi ed, reproduced, republished, trans- mitted or distributed for any purpose, without prior written consent of Lowrance Electronics. Any unauthorized commercial distribution of this manual is strictly prohibited. Lowrance ® is a registered trademark o ...

  • Lowrance electronic 200 - page 3

    i Warnings and Cautions Caution: Use this radar at your own risk. This radar was designed for use as a navigation aid. I t should not be used for purposes that require precise measurements of direction, distance, topograph y or location. Always compare the navigation information received from your radar w ith data from other navigation aids a nd so ...

  • Lowrance electronic 200 - page 4

    ii switching off the radar. Before t ouching the magnetron or any high voltage components, ground them with a clip lead. There are no inte rnal connections or adjust- ments necessary for installation. WARNING: Microwave Radiation Hazard The microwave ener gy radiated by a rad ar antenna is harmful to humans, especially to the eyes. NEVER look direc ...

  • Lowrance electronic 200 - page 5

    1 Section 1: Introduction Thank you for purchasing this Lowrance Radar with the RIM 200 radar interface module. Your radar consists of three m ain components: the radar scanner unit, a display unit (s old separately) and the RIM 200 radar interface module which c onnects the scanner unit an d the display unit. W e k n o w y o u ’ r e a n x i o u ...

  • Lowrance electronic 200 - page 6

    2 rate targets at a dist ance. The critical fact ors are the antenn a's beam width and side lobe level. Typicall y, a radar antenn a will radiate a tightly focused b eam from the fr ont of the array. The longer the a n- tenna array is, the narrower th e beam width. Ad ditionally, it will also emit smaller amounts o f energy to ea ch side. A lo ...

  • Lowrance electronic 200 - page 7

    3 False echoes Sometimes radar will d isplay targets on screen th at do not exist in the real world. You should be awar e of how and why this happens. A. Ghost echoe s Sometimes one large object very near your boat will appear as two dif- ferent targets onscre en. One is the actual radar ech o. The other is a ghost echo generat ed by a re-reflectio ...

  • Lowrance electronic 200 - page 8

    4 Radar interference If another b oat's radar is op erating on th e same frequ ency as yours, it can create interfer ence on your display . The interferenc e usually appears as spira l or radial patterns. This ra- dar has a n interfere nce reje ction contr ol to elimi nate inte rference. Tu rn it on to reduce or e liminate the int erference. I ...

  • Lowrance electronic 200 - page 9

    5 The scanner unit should be m ounted on the center line of your vess el in a location that has an un obstructed view forward a nd is as clear as pos- sible the rest of th e way around the unit. A location as high as practical to impr ove maximu m range is desirable, keeping in mind that minimum range obj ects may be over looked if mounted too high ...

  • Lowrance electronic 200 - page 10

    6 The recommended m ounting surface thickness is 3/8" to 1/2" (9 mm to 13 mm). If the mounting s urface is thin , a doubler should b e added. If it is thicker, longer bolts must be purchased. WARNING: The scanner will be damaged if bolts penetrate more than 9/16" (15 mm). Also, consid er the cable r oute from the scann er to the oper ...

  • Lowrance electronic 200 - page 11

    7 Section 2: Radar Installation Preparations Unpack your new radar and check the contents against the packing list. Do not remove the cover from the unit. There are no conn ections or ad- justments inside the un it needed for installati on or operation. The cable must remain attached. For ease of handling, coil the cab le and place it on top of the ...

  • Lowrance electronic 200 - page 12

    8 8. Secure the ca ble near the sc anner to support th e weight of the cable and prevent strain on the watertight cable sea l. If the cable is to pass through tubing or a bulkhead, pr otect the unfinished end. Do not use the unfinished wires or fabric braid to pull th e cable. Attach a fish cord only to the cable j acket. 9. Route the cable to the ...

  • Lowrance electronic 200 - page 13

    9 Section 3: RIM 200 Installation The RIM 200 will replac e the power cable that ca me with your display unit. Early RIM 200 m odels have four cab les branching out from the cable plug. The cab les include: RI M 200 radar data cable (w ill be con- nected to your radar), RIM 200 powe r cable, display unit p ower/data cable and NMEA 2000 network pow ...

  • Lowrance electronic 200 - page 14

    10 tail Drawing C for open array models . Wiring instructions for bot h ar- ray and radome antennas are listed in text format below. Connecting RIM-200 to L RA 1000, LRA 1500 and LRA 2000 Array antenn as: RIM 200 Brown wir e to Radar Antenna Brown wire RIM 200 Red wire to Ra dar Antenna Red wir e RIM 200 Yellow w ire to Radar Antenn a Yellow wire R ...

  • Lowrance electronic 200 - page 15

    11 Now connect the dis play unit pow er cable green ( RX) receive w ire to the transmit (TX) wire from the NMEA 01 83 device. There is no ground wire, so the NMEA 01 83 device MUST be grounded to the same place as the display unit. NOTE: If your RIM 200 model has four branches, proceed to Step 4 to connect the RIM 200 power cable. If your R IM 200 ...

  • Lowrance electronic 200 - page 16

    12 Connecting RIM 200 to Radome Antenna (Four-Branch Installation) Display unit RIM 200 data cable (RS-422) LRA 1000, LRA 1500 & LRA 2000 See Detail Draw ing C ( Fou r -Branch Installation ) 12V RIM 200 module See Detail Drawing A Radar Power/data output cable Cable Plug Radome antenna * A power switch will only be con- nected to the red (+) wi ...

  • Lowrance electronic 200 - page 17

    13 Connecting RIM 200 to Radome Antenna (Three-Branch Installation) Display unit RIM 200 data cable (RS-422) LRA 1000, LRA 1500 & LRA 2000 See Detail Draw ing D ( Three-Branch Installatio n ) 12V RIM 200 module See Detail Drawing A Radar Power/data output cable Cable Plug Radome antenna * A power switch will only be con- nected to the red (+) w ...

  • Lowrance electronic 200 - page 18

    14 Detail drawing A: wiring di agram, RIM 200 to radome unit. NOTE: If you have a LRA 1000 or LRA 150 0, fuse the radar unit's large white wire (+) with the s upplied 5-amp fuse. If your un it is a LRA 2000, fuse the radar unit' s large white wire (+) wit h the supplied 8- amp fuse. Large black/pwr – ……………… Shield/Small blac ...

  • Lowrance electronic 200 - page 19

    15 Connecting RIM 200 to Open Array Antenna (Four-Branch Installation) Display unit See Detail Drawin g B RIM 200 module See Detail Draw ing C (Four-Branch Installation) 12V Cable Plu g LRA 4000 & LRA 5000 Radar data cable ( RS-422 ) Radar power/data output cable Open array antenna * A power switch will only be con- nected to the red (+) wire. ...

  • Lowrance electronic 200 - page 20

    16 Connecting RIM 200 to Open Array Antenna (Three-branch Installation) Display unit See Detail Drawin g B RIM 200 module See Detail Draw ing D: (Three-Branch Installatio n) 12V Cable Plu g LRA 4000 & LRA 5000 Radar data cable ( RS-422 ) Radar power/data output cable Open array antenna * A power switch will only be con- nected to the red (+) wi ...

  • Lowrance electronic 200 - page 21

    17 Detail drawing B: Wiri ng diagram, RIM 200 to open array unit. NOTE: Fuse both the radar unit' s large Red wire (+) and large White wir e (+) with the supplied 8-amp fuses. Lar g e red + ( fuse ) Large white + (fuse) Large black – Radar motor power { Green Blue ……………………… Orange ……………………… …………… ...

  • Lowrance electronic 200 - page 22

    18 12 volt battery Switchbox RIM 200 module COM Port 2 (RS- 232): blue (TX) & green (RX) Fuse box NMEA 2000 power cable Display unit power cable RIM 200 power cable RIM 200 data cable (RS-422); connects to r adar unit Detail Drawing C: Four-branch Installation * * * * * * * A power switch will only be connected to the red (+) wire. The black wi ...

  • Lowrance electronic 200 - page 23

    19 RIM 200 module 12 volt battery Switchbox COM Port 2 (RS- 232): blue (TX) & green (RX) Fuse box NMEA 2000 power cable Display unit power cable RIM 200 data cable (RS-422); connects to r adar unit Detail Drawing D: Three-branch Installation * * * * * A power switch will only be connected to the red (+) wire. The black wire (–) will not be co ...

  • Lowrance electronic 200 - page 24

    20 Notes ...

  • Lowrance electronic 200 - page 25

    21 Notes ...

  • Lowrance electronic 200 - page 26

    22 Notes ...

  • Lowrance electronic 200 - page 27

    23 Lowrance Radar Specifications Model LRA-1000 LRA-1500 LRA-2000 LRA-4000 LRA-5000 Radome Diameter 1.0 ft. 1.5 ft. 2.0 ft. N/A N/A Open Array Length N/A N/A N/A 4.0 ft. 5.0 ft. Power Output 2 kW 2 kW 4 kW 4 kW 4 kW Power Required 30 watts 55 watts 70 watts 85 watts 95 watts Voltage Required 10.8-41.6 volts DC 10.8-41.6 volts DC 10.8-41.6 volts DC ...

  • Lowrance electronic 200 - page 28

    24 FCC Compliance This device complies with Part 15 of the U.S. Federal Communi- cations Commission (FCC) Rules. Operation is subject to the fol- lowing two conditions: (1) this device may not cause har mful in- terference, and (2) this device mu st accept any interference re- ceived, including interference that may cause undesired opera- tion. Cha ...

  • Lowrance electronic 200 - page 29

    25 LOWRANCE ELECTRONICS FULL ONE- YEAR WARRAN TY "We," "our," or "us" refers to LOWRAN CE ELECTRONICS, INC., the manufacturer of this product. "You" or "your" refers to the first person w ho purchases this product as a consumer item for personal, family or h ousehold use. We warrant this product aga ...

  • Lowrance electronic 200 - page 30

    26 How to Obtain Service… …in the USA: We back your in vestment in qua lity products with quick, exper t service a n d g e n u i n e L o w r a n c e p a r t s . I f y o u ' r e i n t h e U n i t e d S t a t e s a n d y o u have technical, return or repair questions, please contact th e Factory Customer Service De partment. Before any prod ...

  • Lowrance electronic 200 - page 31

    Accessory Ordering Information for all countries To order Lowrance accessories fo r your radar, please contact: 1) Your local marin e dealer or consumer electronics store. Most quality dealers that handle mar ine electron ic equipment or oth er consumer electronics shou ld be able to assist you with th ese items. To locate a Lowrance dealer n ear y ...

  • Lowrance electronic 200 - page 32

    Visit our web site: Lowrance Pub. 988-0161- 042 © Copyright 2007 All Rights Reserved Printed in USA 062707 Lowrance Electronics, Inc. ...

Fabbricante Lowrance electronic Categoria Radar Detector

I documenti che otteniamo dal fabbricante del dispositivoLowrance electronic 200 possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Lowrance electronic
- manuali per l’uso 200
- schede prodotto Lowrance electronic
- opuscoli
- o etichette energetiche Lowrance electronic 200
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Lowrance electronic 200.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Lowrance electronic 200, manuali di manutenzione, brevi manuali o manuali utente Lowrance electronic 200. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Lowrance electronic 200.

Manuali per l’uso simili

Manuale completo del dispositivo Lowrance electronic 200, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Lowrance electronic 200 dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Lowrance electronic 200.

Il manuale per l’uso completo Lowrance electronic, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Lowrance electronic 200 - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Lowrance electronic 200, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Lowrance electronic 200 che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Lowrance electronic 200 - che ci dovrebbe aiutare nei primi passi durante l'uso Lowrance electronic 200
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Lowrance electronic 200
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Lowrance electronic 200 in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Lowrance electronic 200?

Utilizza il modulo sottostante

Se non hai risolto il problema con Lowrance electronic 200 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Lowrance electronic 200 è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)