-
Smeg SCP112-8 - page 1
67 Contents INSTRUCTIONS FOR THE USER: these contain use r advice, description of the commands and the correct procedures fo r cleaning and maintenance of the appliance. INSTRUCTIONS FOR THE INST ALLER: th ese instructions are intended for the qualified tec hnician who m u st pe rf orm the installation, put it into operation and test the appliance. ...
-
Smeg SCP112-8 - page 2
General instructions 68 1. INSTRUCTIONS FOR USE THIS MANU AL IS AN INTEGRAL P ART OF THE APPLIANCE. IT MUST BE KEPT IN ITS ENTIRETY AND IN AN ACCESSIBLE PLA CE FOR THE WHOLE W ORKING LIFE OF THE APPLIANCE. CAREFUL READING OF THIS MANUAL AND ALL THE INSTR UCTIONS THEREIN BEFORE USING THE APPLIANCE IS ESSENTIAL. INST ALLA TION MUST BE CARRIED OUT BY ...
-
Smeg SCP112-8 - page 3
General instructions 69 DO NO T USE STEEL SPONGES AND SHARP SCRAPERS AS TH EY WILL D AMAGE THE SURF ACE. USE NORMAL NON-ABRASIVE PR ODUC TS, INCLUDING W OODEN OR PLASTIC UTENSILS IF NECESSARY . RINSE THOROUG H L Y AND DR Y USING A SOFT CLO T H OR A MICROFIBRE CLO TH. DO NO T ALLOW RESIDUES OF SUGAR Y FOODS (SUCH AS JAM) T O SET INSIDE THE O VEN. IF ...
-
Smeg SCP112-8 - page 4
General instructions 70 2. SAFETY PRECA UTIONS REFER T O THE INST ALLA TION INSTRUCTIONS FOR THE SAFETY REGULA TIONS FOR ELECTRIC OR GAS APPLIANCES AND VENTILA TION FUNCTIONS. IN Y OUR INTERESTS AND FOR Y OUR SAFETY THE LAW REQUIRES THA T THE INST ALLA TION AND SERVICING OF ALL ELECTRICAL APPLIANCES IS CARRIED OUT BY QU ALIFIED PERSONNEL IN ACCORD ...
-
Smeg SCP112-8 - page 5
General instructions 71 DO NO T LET CHILDREN GO NEAR THE APPLIANCE WHEN IT IS IN OPERA TION OR PLA Y WITH IT A T ANY TIME. DO NO T INSERT POINTED MET AL OBJECTS (CUTLER Y OR UTENSILS) INTO THE SLITS IN THE APPLIANCE. DO NO T USE STEAM JETS FOR CLEANING THE APPLIANCE. THE STEAM COULD REACH THE ELECTR ONICS, D AMAGING THEM AND CA USING SHOR T -CIRCUI ...
-
Smeg SCP112-8 - page 6
Instructions f or disposal 72 3. ENVIR O NMENT AL RESPONSIBILITY 3.1 Our en vir onmental responsi bility Pursuant to Directives 2002/95/EC , 200 2/96/EC and 2003/108/EC relating to the reduction of the use of hazardous s ubstan ces in electrical and electronic appliances, as well as to the disposal of refuse. The crossed out bin symbol on the appli ...
-
Smeg SCP112-8 - page 7
Instructions f or the user 73 4. GET T O KNO W Y OUR O VEN Control panel Oven f an Roof liner Bottom plate (on some models only) Inside lights Pizza plate or cov er recess (on some models only) Rack and tray support frames Self-cleaning side panels (on some models onl y) Inser t fo r the rotisser ie rod (on some models onl y) ...
-
Smeg SCP112-8 - page 8
Instructions f o r the user 74 5. A V AILABLE A CCESSORIES NO TE: Some models are not pr ovided with all accessor ies. Rack: f or holding cooking containers. T ray r a ck: to be pl aced ov e r the top of the oven tra y; for cooking f oods which may drip . Oven tray: f or collecting fat from f oods placed on the ra ck ab ove . Deep oven tray : fo r ...
-
Smeg SCP112-8 - page 9
Instructions f or the user 75 Rotisserie rod: f or cooking chic ken and all f oods which require uni f or m cookin g ov er th eir entire surf ace. Pizza plate: specially designed f or cooking pizza and similar dishes. Pizza spatula: for easy placement of the pizza on the pizza p late. Pizza plate cover: for co vering the pizza plate when it is not ...
-
Smeg SCP112-8 - page 10
Instructions f o r the user 76 5.1 Using the rack or tray The racks and tr ays are equipped with a mechanical safety lock which pre vents them from being taken out accidentally . T o inser t the rack or tra y correctly , check that the lock is f acing downwards (as shown in the figure at the side). T o remov e the rack or tra y , lift the front sli ...
-
Smeg SCP112-8 - page 11
Instructions f or the user 77 5.4 Using the r otisserie r od (on some models onl y) When cooking with the rotisser ie, position the frame on the third runner (see 6.2.1 Oven runners). Once the frame is inser ted, the shaped par t must sit facing outwards (as shown in the figure). Then prepare the rotisserie rod with the food, using the clip forks p ...
-
Smeg SCP112-8 - page 12
Instructions f o r the user 78 5.5 Using the pizza plate (on some models onl y) With the ov en cold, remove the circular cov e r from the bottom (as shown in the figure) and inser t the pizza plate. Make sure that the plate is inser ted correctly in the recess provided. T o cook, follo w recipe usage instructions (see 6.11 Selecting a recipe). Do n ...
-
Smeg SCP112-8 - page 13
Instructions f or the user 79 6. USING THE O VEN 6.1 Before u sing the appliance • Remo ve any labels (apar t from the tech nical data plate) fro m tra y s, dripping pans and the cooking compar tment. • Remov e any protective film from t he outside or inside of the appliance, including from accessori es such as tra ys, dr ipping pans, the pizza ...
-
Smeg SCP112-8 - page 14
Instructions f o r the user 80 6.2.3 Oven inside lights The ov en li ghts come on when the do or is opened or any function or recipe is selected, e xcept for , and (where present). When set to ON, the oven lights can be switched on/ off by briefly pressing the on/off button. (ON/OFF knob) 6.3 W arnings and general advice for usa g e All cooking ope ...
-
Smeg SCP112-8 - page 15
Instructions f or the user 81 T o prev ent any steam in the ov en fro m causing problems, open the door in two stages: half open (5 cm approx.) f or 4-5 seconds an d then fully open. If you need to access the f ood, alwa ys leave the door open f or as shor t a time as possible to pre vent the temperature in the ov en from falling and ruining the fo ...
-
Smeg SCP112-8 - page 16
Instructions f o r the user 82 6.4 Description of the contr ols on the front panel All the appliance's control and monitor ing devices are located together on the front panel. T emperature selection knob ON/OFF knob This knob can be used to: set the clock, select a temperature and the cooking time, and set programmed cooking. (T emperature kno ...
-
Smeg SCP112-8 - page 17
Instructions f or the user 83 If the symbols to the side of the display are lit up, it means: Indicates that the door lock is activated (on p yrolytic models only). In multifunction models, this symbol is replaced with which indica tes that the "showroom" mode is activated (see 6.14 Secondar y me nu). If flashing, it indicates that the ti ...
-
Smeg SCP112-8 - page 18
Instructions f o r the user 84 6.5 Operating modes This appliance has three ope rating modes which can be activated by pressing the on / off knob . ST AND-BY setting: the appliance displays the current time (activ ated as soon as the current time has been confir med). ON setting: from the standby setting, press t he ON/OFF knob once. It is now poss ...
-
Smeg SCP112-8 - page 19
Instructions f or the user 85 6.7 Setting the current time T ur n the temperature selecti on knob ri ght or left to reduce or increase the display ed ti me. K eep it in the tur ned position to reduce or increase more rapidly . (T e mperature knob) A f ew seconds after the last adj ustment is made, the time display will steady and the colon separati ...
-
Smeg SCP112-8 - page 20
Instructions f o r the user 86 On p yrolytic models, the special defrosting and proving functions are brought together under the same function indicated by . See “7.4 Proving and defrosting functio ns” f o r fur ther details. Cooking can be interrupte d at any time by holding down the ON/OFF knob fo r a t least two seconds . 6.8.1 Modifying the ...
-
Smeg SCP112-8 - page 21
Instructions f or the user 87 At this point it is possible to select the desired cooking function and wait for the b uzzer to sound, indicating that the cooking time is ov er . Press the temperature selection knob to s wi tch off the buzzer . The symbol flashes, and anoth er time can then be selected by turning the same knob right or left. (T e mpe ...
-
Smeg SCP112-8 - page 22
Instructions f o r the user 88 6.10 Progra mmed cooking 6.10.1 Semi-automatic cooking Semi-automatic cooking is the functio n which allows a cooking operation to be star ted and then ended after a specific length of time set by the user. Select a cooking function as descr ibed in "6.8 Selecting a cooking function". Press the temperature s ...
-
Smeg SCP112-8 - page 23
Instructions f or the user 89 T o extend the cooking ti me manually (if the food has not been cooked proper ly), press the te mperature selection knob again. The applia nce will restar t its nor mal operation with the previously selected cooking settings. (T e mperature knob) T o completely switch off the appliance, press the ON/OFF knob for 2 seco ...
-
Smeg SCP112-8 - page 24
Instructions f o r the user 90 6.10.2 A utomatic cooking Automatic cooking is the function which allows a cooking operation to be star ted at a set time and then ended after a specific length of time set by the user . Select a cooking function as descr ibed in “6.8 Selecting a cooking function”. Press the temperature selection knob twice. The d ...
-
Smeg SCP112-8 - page 25
Instructions f or the user 91 When cooking is complete, the word ST OP will appear , cook ing will be interr upted and a buzzer will sound which can be deactivated by pressing the temperature selection knob . It is also possible to select an additional cookin g time semi-autom atically by tu r ning the temper ature selection knob . (T e mperature k ...
-
Smeg SCP112-8 - page 26
Instructions f o r the user 92 6.11 Selecting a recipe The appliance is equipped with preset re cipes and 3 free recipes. A recipe is a combination of preset functions, temperatures, cooking times and shelf position for the dish. In the ON state only , a recipe can be selected by simply turning the ON/OFF knob to the right or left. (ON/OFF knob) Th ...
-
Smeg SCP112-8 - page 27
Instructions f or the user 93 6.11.1 Modifying the set data During cooking with a recipe, it is possible to modify the preset temperature by tur ning the temperature selection knob . T o alter the time, press the temperature selection knob then turn it right or left. (T e mperature knob) (T e mperature knob) The modifications to the set da ta must ...
-
Smeg SCP112-8 - page 28
Instructions f o r the user 94 6.12 P ermanently modifying a recipe The appliance is equipped with preset recipes and three free recipes indi cated by . T o modify or set a recipe per manently: In ON mode, select the recipe to be modified by tur ning the ON/OFF knob right or left. (ON/OFF knob) Within 5 seconds, press and hold the temperature selec ...
-
Smeg SCP112-8 - page 29
Instructions f or the user 95 Press the temperature selection knob to confirm the modification and go on to modifying the cooking time. (T e mperature knob) T ur n the temperature selecti on knob ri ght or left to alter the cooking time associated with the recipe. (T e mperature knob) Press the temperature selection knob to confirm the change and g ...
-
Smeg SCP112-8 - page 30
Instructions f o r the user 96 6.13 T able of pred efined recipes: Class Ty p e Qty . Te m p . (°C) Cooking time (min.) Funct. Runner Beef Roast beef 0.7 kg 200 30 1 kg 200 40 1.5 kg 200 65 Po r k Roast 0.5 kg 180 50 1 kg 190 80 1.5 kg 180 110 Chicken Ro a s t c h icke n 0.5 kg 190 40 1 kg 200 60 2 kg 180 90 Lamb Roast leg of lamb 1.0 kg 190 65 1. ...
-
Smeg SCP112-8 - page 31
Instructions f or the user 97 The cooking times in the table ref er to the food indicated in the recipe and are a guide only; they ma y vary depending on the weight. The table giv es the factory-set data. T o reset a recipe with the o riginal settings after it has been modified, just enter the data given in the table . If the limited power mode is ...
-
Smeg SCP112-8 - page 32
Instructions f o r the user 98 6.14 Secondary men u The appliance also has a concealed se condar y menu allowing the user to: • Activate or deactivate the child lock mode. • Activ ate or deactivate Showroom mode (which disables all the heating elements so that only the control panel works). • Activ ate or deactivate low po wer mode. With the ...
-
Smeg SCP112-8 - page 33
Instructions f or the user 99 6.14.1 Child lock mode By activating this mode, after two min utes of operation without any inter vention from the user , the controls will automatically be locked, indicated by lighting up. T o temporar ily release the lock during cooki ng, hold down the temperature selection knob for 5 seconds. T wo minutes after the ...
-
Smeg SCP112-8 - page 34
Instructions f o r the user 100 7. COOKING WITH THE O VEN ECO: Using the grill and the low e r heating element in combinati on is par ticular ly suitable for cooking on a single runner on ly , as it provides low energy consumption. ST A TIC : As the heat comes from above and below at the same time, this system is par ticularly suitable for certain ...
-
Smeg SCP112-8 - page 35
Instructions f or the user 101 F AN-ASSISTED GRILL: The air produced by the fan softens the strong heatwav e generated by the grill, giving perfect grilling e ven with v er y thick f oods. P erfect f or larg e cuts of meat (e.g. shin of pork). We recommend using the 4 th runner . F AN-ASSISTED BOTT OM: The combinatio n of the fan with just the lowe ...
-
Smeg SCP112-8 - page 36
Instructions f o r the user 102 7.1 Cooking ad vice and instructions 7.1.1 General advice W e recommend preheating the oven bef ore putting the f ood in. Do not place foods inside the ov en until on the display stops flashing and the beep has sounded to confir m that the programmed temp erature has been reached. F or cooking on sever al levels , we ...
-
Smeg SCP112-8 - page 37
Instructions f or the user 103 When defrosting meat, we recomme nd using a rack positioned on th e second runner with the food on it and a tra y p ositioned on the first r unner . In this way , the liquid from the defrosting food dr ains aw ay from the f oo d. The most delicate par ts can be cov ered with alumini um f o il. F or successful proving, ...
-
Smeg SCP112-8 - page 38
Instructions f o r the user 104 7.3 Cooking pro cess inf ormation table DISHES WEIGHT FUNCTION FIRST COURSES LASAGNE 3 kg Static O VEN-BAKED P AST A Static MEA T RO AST VE AL 1 kg F an-as sisted static LOIN OF PORK 1 kg F an-assist ed static SHOULDER OF PORK 1 kg T urbo RO AST RABBIT 1 kg Circular TURKEY BREAST 1 kg F an- assisted static RO AST NEC ...
-
Smeg SCP112-8 - page 39
Instructions f or the user 105 RUNNER POSITION FRO M BO TT OM TEMPERA TURE °C TIME IN MINUTES 1 or 2 220 - 230 40 - 50 1 or 2 220 - 230 40 2 180 - 190 70 - 80 2 180 - 190 70 - 80 2 180 - 1 90 90 - 100 2 180 - 190 70 - 80 2 180 - 1 90 110 - 120 2 180 - 1 90 190 - 210 2 190 - 200 60 - 70 1 ST SURF ACE 2 ND SURF A C E 4 250 - 280 7 - 9 5 - 7 3 250 - ...
-
Smeg SCP112-8 - page 40
Instructions f o r the user 106 DISHES WEIGHT FUNCTION PIZZA F an-assisted st atic BREAD Circular FOCA CCIA Tu r b o DESSERTS DOUGHNUT F an-assi sted static FR UIT T AR T F an-assisted static FR UIT T ART Static SHOR T P ASTR Y Circular JAM T AR T S T urbo P ARADISE CAKE F an-assisted stat ic P ARADISE CAKE Static ECLAIR T urbo LIGHT SPONGE CAKE Ci ...
-
Smeg SCP112-8 - page 41
Instructions f or the user 107 RUNNER POSITION FRO M BO TT OM TEMPERA TURE °C TIME IN MINUTES 1 250 - 280 6 -10 2 190 - 200 25 -30 2 180 - 190 15 -20 2 160 55 - 60 2 160 30 - 35 2 170 35 - 40 2 160 - 170 20 - 25 2 160 20 - 25 2 160 55 - 60 2 170 50 - 60 2 150 - 160 40 - 50 2 150 - 160 45 - 50 2 160 40 - 50 2 170 50 - 60 2 160 25 - 30 31 8 0 6 0 2 ...
-
Smeg SCP112-8 - page 42
Instructions f o r the user 108 7.4 Pro ving and defrost i ng functions On py ro lytic models, the special defrosting and proving functions are brought togethe r under the same function indicate d by . The choice of temp erature deter mines whether defrosting or proving takes place based on the table belo w . On multifunction models, it i s not po ...
-
Smeg SCP112-8 - page 43
Instructions f or the user 109 8. CLEANING A ND MAINTENANCE NEVER USE A STEAM JET FOR CLEANING THE APPLIANCE. We recommend the use of cleaning products distributed by SMEG. 8.1 Cleaning stai nless steel T o keep stainless steel in good condition it should be cleaned regular ly after use. Let it cool first. 8.2 Or dinary daily c leaning T o clean an ...
-
Smeg SCP112-8 - page 44
Instructions f o r the user 110 8.5 Cleaning the inside of the o ven F or the best oven upk eep, clean it regular ly afte r having allowed it to cool. • T ake out al l removab le p ar ts. • C lean the ov en racks with hot w ater and non-abrasive detergent. Rinse and dry . • For easier cleaning, the door can be remov ed (see “9.2 Removing th ...
-
Smeg SCP112-8 - page 45
Instructions f or the user 111 Lift up the edge of the lower heating element a fe w centimetres and clean the bottom. Put the pizza plate suppor t back in place, pushing it in until it hits the back of the o ven, and push it down so that the heating element plate is embedded into the base itself. When the operation is complete, damp par ts should b ...
-
Smeg SCP112-8 - page 46
Instructions f o r the user 112 8.6 Cleaning the pizza pl ate The pizza plate (where included) sh ould be washed separately according to the f o llowing instructions: Pyrol ytic models: leave the pizza stone inside and activate the p yrolysis function, then at the end, when th e stone has cooled down to lukewarm, wipe it with a damp microfibre clot ...
-
Smeg SCP112-8 - page 47
Instructions f or the user 113 8.7 Pyr olysis: automati c oven cle aning (on so me models only) Pyrolysis is an automatic high-temperature cleani ng procedure which causes dir t to dissolve. Thanks to this process, it is possible to clean the inside of the ov en ver y easily . During the first a utoma tic cleaning cycle, unpleasant smells ma y occu ...
-
Smeg SCP112-8 - page 48
Instructions f o r the user 114 • Remove the guide frames, see “8.5.1 Removing guide frames”. • At the end of the cleaning cycle, when the ov en ha s cooled down, reinser t the frames by repeating the pre viously used procedure in rev erse order . • Make sure that the oven door is fir mly closed. Refer to the f o llowing diagram f or se t ...
-
Smeg SCP112-8 - page 49
Instructions f or the user 115 8.7.2 Setting the cleaning cyc le In ON mode (see 6.5 Operating modes), tur n the ON/OFF knob right or left to select one of the two cleaning cycles out of and . (ON/OFF knob) T o star t the cleaning cycle (pyrolysis), the temperature selection knob must be pressed. will light up to indicate that it is now possib le t ...
-
Smeg SCP112-8 - page 50
Instructions f o r the user 116 T o selec t a cleaning cyc le with delayed start , after setting the duration press the temperature selection knob once. and the current time will appear on the display . (T emperature knob) T ur n the knob r ight or left to increase or decrease the time when you w ant to star t the cleaning cycle. (T emperature knob ...
-
Smeg SCP112-8 - page 51
Instructions f or the user 117 8.8 V APOR CLEAN: assisted oven cleaning (on some models only) V APOR CLEAN is an assisted cleanin g pr ocedure which facilitates the remov al of dir t. Thanks to this process, it is possible to clean the inside of the oven v er y easily . The dir t residues are softene d by the heat and water vapour f or an ea sier r ...
-
Smeg SCP112-8 - page 52
Instructions f o r the user 118 IN PIZZA MODELS • Remo ve any accessories. In order to sav e energy , you are advised to remov e the pizza plate and put the cov er back in its slot. • Place a tra y on the base of the ov en as shown in the figure. • P our approximately 40 cl of water into the tra y . Make sure it does not ov erfl ow out of the ...
-
Smeg SCP112-8 - page 53
Instructions f or the user 119 In ON mode (see 6.5 Operating modes), tur n the ON/OFF knob right or left to select the V APOR CLEAN cleaning cycle. (ON/OFF knob) T o star t the cleaning cy cle (V APOR CLEAN), the temperature selection knob must be pressed. will light up to show that the cleaning phase is in progress. (T e mperature knob) The displa ...
-
Smeg SCP112-8 - page 54
Instructions f o r the user 120 9. EXTRA ORDINAR Y MAINTENANCE The ov en may require extraordinary ma intenance or repla cement of par ts subject to wear such as gask ets, b ulbs, etc. The fo llowing instructions descr ibe how to carry out these minor main tenance operations. Before an y inter vention that requires acces s to live parts, disconnect ...
-
Smeg SCP112-8 - page 55
Instructions f or the user 121 9.2 Remo ving the door 9.2.1 With mo veable lever s Open the door completely . Lift the lev ers A of the two hinges aw ay from them until they engage. Grasp the door on both sides with both hands, lift it forming an angle of around 30° and remove it. If the hinges hav e not unlocked, repeat the operation, raising the ...
-
Smeg SCP112-8 - page 56
Instructions f o r the user 122 9.2.2 With pi ns Open the door co mpletely . Inser t two pins into the holes indica ted A in the two hinges towards the back of them until they engage . Grasp the door on both sides with both hands, lift it f or ming an angle of arou nd 30° and remov e it. T o reassemble the door , p ut the hinges in the relev ant s ...
-
Smeg SCP112-8 - page 57
Instructions f or the user 123 9.3 Remo ving the door seal For multifunction mo dels only: T o per mit thorough cleani ng of the ov en, the door seal may be remo ved. There are fasteners on all f ou r sides to attach it to the edge of the oven. Pull the edges of the seal outwards to detach the f asten ers. ...
-
Smeg SCP112-8 - page 58
Instructions f o r the user 124 9.4 Remo ving the internal glass panels The glass in the door sh ould alwa ys be kept thoroughly clean. T o facilitate cleaning, it is possi ble to remo ve the door (see 9.2 Removing the door) and place it on a canvas , or ope n it and lock the hinges in order to extract the glass panels. The glass panels of the door ...
-
Smeg SCP112-8 - page 59
Instructions f or the user 125 Cleaning: • Now it is possible to clean the external glass panel and the panels removed pre viously . Use absorbent kitchen roll. In the case of stubbor n dir t, wash with a damp sponge and neutral dete rgent. Replacing the glass panels: • Re place the panels in th e re verse of the order in which the y were remov ...
-
Smeg SCP112-8 - page 60
Instructions f o r the user 126 9.5 What to do if... The ov en display is completely off • Check the mains po wer supply . • Ch eck whether an omnipolar s witch upstream of the oven supply line is in the “ON” position. The ov en does not hea t up • Check whether it has been set in “showroom” mode, f or fur ther details see “6.14 Sec ...
-
Smeg SCP112-8 - page 61
Instructions f o r the installer 127 10.INST ALLING THE APPLIANCE 10.1 Electr ical connection The identificati on plate bearing the technical data, seria l number and brand name is visibly positioned on the appliance. Do not remove this plate f or any reason. The appliance must be connected to ear th in compliance with electr ical system saf ety re ...
-
Smeg SCP112-8 - page 62
Instructions f o r the installer 128 10.2 Cable repl acement Should the supply cable need replacing, remov e th e back guard b y unscrewing the screws to gain access to the terminal. Replace t he cable. The cable c ross- section must be no less than 1.5 mm² (3 x 1.5) (see 10.1 Electri cal connection). Make sure that the cab les (for the o ven or a ...
-
Smeg SCP112-8 - page 63
Instructions f o r the installer 129 When installing in tal l units, comply with the dimensions shown in figures 1 and 2 , bearing in mind th at the top/rear of the unit must hav e an opening 35-40 mm deep . Remov e the screw cov ers on the frame and screw in the 2 scre ws A (fig. 5) to fix the appliance to the u nit. Replace the screw cov ers. For ...
-
Smeg SCP112-8 - page 64
Instructions f o r the installer 130 FIG. 2 FIG. 3 FIG. 4 FIG. 5 ...
Hai una domanda su Smeg SCP112-8?
Utilizza il modulo sottostante
Se non hai risolto il problema con Smeg SCP112-8 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Smeg SCP112-8 è probabile che voglia condividere il modo di risolverlo.