Italiano dropdown-ico

Manuale per l’uso Master Lock ATS 211

32 pagine 0.78 mb
Scarica

Vai alla pagina of 32

Summary
  • Master Lock ATS 211 - page 1

    © The Chamberlain Group, Inc. A DUCHOSSOIS ENTERPRISE 845 Larch Avenue, Elmhurst, Illinois 60126 OWNER'S MANUAL MODEL A TS 21 1 COMMERCIAL DOOR OPENER For Residential and Light Duty Commercial Use Install on Sectional Doors Only Please read this manual and the enclosed safety materials carefully! Fasten the manual near the garage door after i ...

  • Master Lock ATS 211 - page 2

    Start by reviewing these important safety alert symbols 2 CONTENTS PAGE A review of safety alert symbols ..............................2 You'll need tools ......................................................3 Illustration of door installation .................................4 Opener carton inventory ......................................... ...

  • Master Lock ATS 211 - page 3

    3 • Lift the door about halfway as shown. Release t he door . It should stay in place, support ed en tirely by its springs. • Raise and lower the door to see if t here is any binding or sticking. An unbalanced garage door might not reverse when required and someone under the door could be seriously injured or killed. If your garage door binds, ...

  • Master Lock ATS 211 - page 4

    4 Safety Reversing Sensor Horizontal and vertical reinforcement is needed for lightweight garage doors (fiberglass, steel, aluminum, door with glass panels, etc.). See page 19 for details. Support bracket & fastening hardware is required. See page 12. — — — — — — — — Door Center Header Wall Safety Reversing Sensor Floor must be ...

  • Master Lock ATS 211 - page 5

    5 Straight Door Arm Door Bracket Plate Door Bracket Safety Labels and Literature "C" Wrap (2) Safety Reversing Sensor Mounting Bracket With Slot (2) 2 -Conductor Bell Wire White & White/Red Curved Door Arm 2 -Conductor Bell Wire with Connector (2 rolls) White & White/Black Rail Styrofoam Chain Pulley Bracket Trolley Chain Safety R ...

  • Master Lock ATS 211 - page 6

    Chain Spreader Sprocket Chain USE ONLY THIS TYPE AND SIZE  SCREW Washered Screw 5/16"-18x1/2" Opener 6 • Guide the chain over chain spreader and opener sprocket. If necessary, loosen the outer nut on the trolley to obtain more chain slack. Insert the second washered screw. CAUTION! Use only the screw previously removed from ...

  • Master Lock ATS 211 - page 7

    • Spin the inner nut and lock washer down t he threaded shaft, away from t he t rolley . • T o tighten t he chain, tur n outer nut in the direction shown. As you turn the nut, keep the chain from twisting. • When the chain is approximat ely 1/2" above the base of the rail at its midpoin t, re-tighten the inner nut to secure the ad justme ...

  • Master Lock ATS 211 - page 8

    • Open your door to the highest point of travel as shown. Draw an intersecting horizontal line on the header wall 2" above the high point. This height will provide travel clearance for the top edge of the door. Header Wall Ceiling Track Highest Point of Travel Door 2" 8 Proceed to Step 2, page 9. Header Wall Ceiling Track Highe ...

  • Master Lock ATS 211 - page 9

    Lag Screws 5/16"x18x1-7/8" Highest Point of Travel (of Garage Door) Vertical Center Line Header Wall Garage Door Mounting Header Bracket to WALL UP CEILING MOUNT ONLY Wall Mounting Holes Optional Wall Mounting Holes The nail hole is for positioning only. You must use lag screws to mount the header bracket. UP CEILING MOUNT ONLY 2" Do ...

  • Master Lock ATS 211 - page 10

    Header Bracket Chain Pulley Bracket Temporary Support Header Wall Garage Door Clevis Pin 5/16"x2-3/4 " Ring Fastener Header Bracket Chain Pulley Bracket Rail Rail • Position the opener on the garage floor below the header bracket. Use packing material as a protective base. If the door spring is in the way you&apo ...

  • Master Lock ATS 211 - page 11

    Installation Step 4 Position the Opener To prevent damage to steel, aluminum, fiberglass or glass panel doors, do not rest the opener on the door without using a 2x4. 11 CAUTION Trolley Trolley Release Arm • If the top panel hits the trolley when you raise the door, pull down on the trolley release arm to disconnect the inner and outer section ...

  • Master Lock ATS 211 - page 12

    Installation Step 5 Hang the Opener Two representative installations are shown. Yours may be different. Hanging brackets should be angled, Figure 1, to provide rigid support. On finished ceilings, Figure 2, attach a sturdy metal bracket to structural supports in ceiling before installing the opener. The bracket and fastening hardware are not suppli ...

  • Master Lock ATS 211 - page 13

    Installation Step 6 Install the Door Control 13 Children operating or playing with a garage door opener can injure themselves or others. The garage door could close and cause serious injury or death. Install the Door Control (or any additional push buttons) out of the reach of children and away from all moving parts of the door and door hardware, b ...

  • Master Lock ATS 211 - page 14

    Opener 75 Watt Max. Light Bulb Install the Light • Install a 75 watt maximum light bulb in the socket. The light will t ur n ON and remain lit for approximately 4-1/2 minut es when power is connected. Then t he light will tur n OFF . • If the bulb bur ns out premat urely due to vibration, replace with a "Garage Door Opener" bulb. I ...

  • Master Lock ATS 211 - page 15

    To reduce the risk of electric shock, your garage door opener has a grounding type plug with a third grounding pin. This plug will only fit into a grounding type outlet. If the plug doesn't fit into the outlet you have, contact a qualified electrician to install the proper outlet. Installation Step 9 Electrical Requirements Ground Tab Green Gr ...

  • Master Lock ATS 211 - page 16

    The safety reversing sensor must be connected and aligned correctly before the garage door opener will move in the down direction. This is a required safety device and cannot be disabled. Without a properly working safety reversing sensor , persons (particularly children) could be killed by a closing garage door . Read and follow all instructions. ...

  • Master Lock ATS 211 - page 17

    1/4x1-1/2" Lag Screw #10-32x3/8" Screw 1/4"-20 Lock Nut  #10x32 Lock Nut  Staples 1/4"-20x1/2" Carriage Bolts  Installation Step 10 Install the Safety Reversing Sensor (Receiving and Sending Eyes) Mounting Bracket With Square Holes  #10-32x3/8" Screws "C" Wrap #10- ...

  • Master Lock ATS 211 - page 18

    1/4-20x1-1/2" Hex Bolt "C" Wrap Wire Sensor Wing Nut Invisible Light Beam Protection Area Sensor Sensor Connect Wire to Opener Terminals Bell Wire Bell Wire Finished Ceiling Indicator Light Sensor Connections Wall Control Connections (dotted line) OPENER TERMINAL SCREWS 1 2 3 • Run paired wires from both sensors to the opener. Use ...

  • Master Lock ATS 211 - page 19

    Vertical Guideline Door Bracket Nut 5/16"-18 Carriage Bolt 5/16"-18x2-1/2" Lock Washer 5/16" Vertical Guideline Door Bracket Location Header Bracket Door Bracket Door Bracket Plate Inside Edge of Door or Reinforcement Board Horizontal and vertical reinforcement is needed for lightweight ...

  • Master Lock ATS 211 - page 20

    Installation Step 12 Connect Door Arm to T rolley Make sure garage door is fully closed. Pull the manual release handle to disconnect the outer trolley from the inner trolley. Slide the outer trolley back (away from the door) about 2” as shown in Figures 1, 2 and 3. Figure 2: • Bring arm sections together. Find two pairs of holes that line up a ...

  • Master Lock ATS 211 - page 21

    Adjustment Step 1 Adjust the UP and DOWN Limits 21 Limit adjustment settings regulate the points at which the door will stop when moving up or down. The door will stop in the up direction if anything interferes with door travel. The door will reverse in the down direction if anything interferes with the door travel (including binding or unbalanced ...

  • Master Lock ATS 211 - page 22

    Ad justment Step 2 Adjust the Force T oo much force on the door will int erfere with the proper operation of t he safety reverse system. See page 23. The door might not reverse properly when required and could seriously injure or kill someone under it. Do not increase the force beyond what is required to close the door . Do not use the force ad jus ...

  • Master Lock ATS 211 - page 23

    Adjustment Step 4 T est the Safety Reverse System Test: • Place a 2x4 laid flat on the floor, centered under the garage door. • Operate the door in the down direction. The door must reverse on striking the obstruction. Adjustment: If the door stops on the obstruction, it is not traveling far enough in the down direction. • Increase the DOWN l ...

  • Master Lock ATS 211 - page 24

    Limit and Force Adjustment Control Weather conditions may cause some minor changes in door operation requiring some re- adjustments, particularly during the first year of operation. Pages 21 and 22 refer to the limit and force adjustments. Only a screwdriver is required. Follow the instructions carefully. Repeat the safety reverse test (page 23) af ...

  • Master Lock ATS 211 - page 25

    The lockout feature prevents the trolley from reconnecting automatically. Pull the manual release handle down and back (toward the opener). The door can then be raised and lowered manually as often as necessary. To disengage the lockout feature, pull the manual release handle straight down. The trolley will reconnect on the next UP or DOWN operatio ...

  • Master Lock ATS 211 - page 26

    1. Have you disabled all door locks? Review installation instruction warnings on page 7. 2. Does the opener have electric power? Plug a lamp into the outlet. If it doesn't light, check the fuse box or the circuit breaker. (Some outlets are controlled by a wall switch.) 3. Repeated operation may have tripped the overload protector in the motor. ...

  • Master Lock ATS 211 - page 27

    Having a Problem? (continued) Situation Probable Cause & Solution The door reverses for no apparent reason and opener light doesn't blink: 1. Is something obstructing the door? Pull the red manual release handle. Operate the door manually. If it is unbalanced or binding, call a garage door serviceman to correct the problem. 2. Clear any ic ...

  • Master Lock ATS 211 - page 28

    6 UP CEILING MOUNT ONLY 9 8 1 NOTICE 3 5 4 7 11 10 12 13 2 2 1 3 4 RAIL GREASE NO. 83A4 5 Repair Parts Rail Assembly Parts Installation Parts 28 KEY PART NO. NO. DESCRIPTION 1 1A995 Master link kit 2 41A2780 Chain pulley bracket 3 41A3489 Complete trolley assembly 4 CD1008 8 Foot Rail Assembly CD1010 10 Foot Rail Assembly CD1012 12 Foot Rail Assemb ...

  • Master Lock ATS 211 - page 29

    Repair Parts Opener Assembly Parts 1 9 7 12 13 14 15 18 4 8 11 17 10 16 3 5 6 18 15 2 DN UP Brown Wire (Down) Contact LIMIT SWITCH ASSY. Grey Wire Yellow Wire (Up) Contact Center Limit Contact Drive Gear KEY PART NO. NO. DESCRIPTION 1 41D4478 Rail support bracket assembly kit 2 144B18 Pulley (Chain) 3 41C4470 Gear and sprocket ...

  • Master Lock ATS 211 - page 30

    Accessories A vailable for your Opener Model 63LM Model 64LM Model 60 Model 66LM Model 1702 Multi-Function Standard Size Remote Control: Includes visor clip. Multi-Function Mini Remote Control: With key ring & Velcro fastening strip. Keyless Entry: Enables homeowner to operate garage door opener from outside by entering code on specially design ...

  • Master Lock ATS 211 - page 31

    Index Access Door/Outside Quick Release Accessory ................................................................................................4 Chain Tension ....................................................................................................................................................4, 7 Electrical Safety Warnings ........ ...

  • Master Lock ATS 211 - page 32

    LIFT-MASTER GARAGE DOOR OPENER ONE-YEAR LIMITED WARRANTY The Chamberlain/Lift-Master warrants to the first retail purchaser of this product that it will be free from any defect in materials and/or workmanship for a period of twelve full months from the date of purchase. The product must be used in complete accordance with Lift- Master's instru ...

Fabbricante Master Lock Categoria Garage Door Opener

I documenti che otteniamo dal fabbricante del dispositivoMaster Lock ATS 211 possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Master Lock
- manuali per l’uso ATS 211
- schede prodotto Master Lock
- opuscoli
- o etichette energetiche Master Lock ATS 211
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Master Lock ATS 211.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Master Lock ATS 211, manuali di manutenzione, brevi manuali o manuali utente Master Lock ATS 211. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Master Lock ATS 211.

Manuali per l’uso simili

Manuale completo del dispositivo Master Lock ATS 211, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Master Lock ATS 211 dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Master Lock ATS 211.

Il manuale per l’uso completo Master Lock, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Master Lock ATS 211 - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Master Lock ATS 211, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Master Lock ATS 211 che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Master Lock ATS 211 - che ci dovrebbe aiutare nei primi passi durante l'uso Master Lock ATS 211
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Master Lock ATS 211
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Master Lock ATS 211 in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Master Lock ATS 211?

Utilizza il modulo sottostante

Se non hai risolto il problema con Master Lock ATS 211 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Master Lock ATS 211 è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)