-
Audiovox LCM5043NP - page 1
LCM5043NP & LCM5643NP Remote Controlled Color Display Monitor with Headphone Jack Installation and Owner's Manual EL E C T R O N I C S C O R P . ® ...
-
Audiovox LCM5043NP - page 2
1 EXPLANA TION OF GRAPHIC SYMBOLS W ARNING: TO PREVENT FIRE OR ELECTRIC SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. CAUTION: 1. This product is designed to operate with a 12 volt, negative ground bat- tery system. 2. Disconnect the ground wire from the battery terminal before connecting the electrical system. Refer to the electric ...
-
Audiovox LCM5043NP - page 3
2 SYSTEM OVERVIEW The LCM5043NP is comprised of a 5" Thin Film Transistor (TFT) Liq- uid Crystal Display ( LCD) Monitor . The LCM5643NP is comprised of a 5.6" Thin Film T ransistor (TFT) Liquid Crystal Display ( LCD) Monitor . The Monitor for both of these systems have a 4:3 Aspect Ratio display that allows the user to select between two ...
-
Audiovox LCM5043NP - page 4
MA TERIALS LIST 1. System Monitor (LCM5043NP=136C2187) or (LCM5643NP=136C2186) (1pc.) 2. Remote Control Unit (136B2156) with Lithium Battery , 3V ,CR 2025 (1pc.) 3. Interconnect Box (136B2183) (1pc.) 4. Monitor Cable, 8' (1 12B3152) (1pc.) 5. Headrest Mounting Tray (LCM5043NP=102C3740) or (LCM5643NP=102C3742) (1pc.) 6. Trim Ring for Mounting T ...
-
Audiovox LCM5043NP - page 5
VEHICLE PREP ARA TION 1 ) Decide on the system configuration and the options that will be in- stalled (i.e. what components, VCP , DVD, TV T uner , Video Game, Monitor , FM Modulator , etc.). 2 ) Read the manuals and get familiar with the electrical requirements and connections. 3 ) Decide on the mounting locations and methods of mounting the prod- ...
-
Audiovox LCM5043NP - page 6
5 10 ) After verifying the proper operation of the system, proceed to mount each component. 1 1 ) The mounting method, and the location will vary from vehicle to vehicle, so this manual will only focus for the installation of the 1 2) The best location for the system components is: a) Monitor: Headrest or bracket (optional) mounted onto a flat surf ...
-
Audiovox LCM5043NP - page 7
6 3 ) Adjust viewing angle of monitor by tightening the fastener at the side. 4 ) When the system components are mounted, test the system to verify that it is functioning correctly . Make sure that no wiring was pinched, or connected improperly during the final installation. Surface Mount Mounting Bracket Fastener Wheel Monitor 2) Slide monitor ont ...
-
Audiovox LCM5043NP - page 8
7 1 ) Remove the headrest from the vehicle for easiest installation. 2 ) Lay headrest on a flat surface. 3 ) Center trim collar on headrest as shown. NOTE: Depending on the angle of the headrest the Trim Ring and housing may be mounted upside down. 4) Using a Permanent Marker , mark headrest material along the interior of the Trim Ring. 5 ) Remove ...
-
Audiovox LCM5043NP - page 9
9 ) Using your fingers, tear the foam out of the headrest leaving a re- cess where the shell will be in- serted. NOTE: At this point you will need to install the harness up through the area into the recess. It may be helpful to follow one of the posts and tie wrap it to the post for restraint. 6 ) Using the utility knife, cut the headrest material ...
-
Audiovox LCM5043NP - page 10
1 1 ) Guide the cable through the side opening of the Mounting Tray and plug it into the Monitor . Make sure the connector locks into place. Insert the Monitor into the Mounting Tray and secure the cable using tie wraps or screws 1 2) Turn the Monitor around and in- sert it into the Mounting Tray housing. Snap into place. 1 0 ) Lay the flaps of hea ...
-
Audiovox LCM5043NP - page 11
ELECTRICAL CONNECTION (Wiring Diagram) 10 Video Source Input (1&2) Not Used A V Output ...
-
Audiovox LCM5043NP - page 12
The following procedure is to remove the Monitor from the Mounting T ray using the supplied Removal T ool. NOTE: Use care when per- forming this procedure not to scratch any exposed surfaces with the edges of the Removal T ool. Masking tape applied to the two tips or legs of the Removal T ool will help prevent scratching. 11 Monitor Removal: 1) Loc ...
-
Audiovox LCM5043NP - page 13
CONTROLS AND INDICA TORS Headphone OPERA TION 1. Press power On/Off button to the On position. The LED power indicator will light red. 2. Press the Picture Select button to adjust the picture display characteristics. The adjustments will be shown on the On Screen Display in the following sequence: Contrast, Brightness, Color , and TINT . 3. While i ...
-
Audiovox LCM5043NP - page 14
MAINTENANCE T o avoid electrical shock, do not open the enclosure. High voltage is present. No user serviceable parts inside the enclosure. Do not use any chemical solvent, cleaning agent or corrosive de- tergent to clean away dirt on the surface of the screen. T o clean off dirt or fingerprint, we recommend the use of a soft damp lens clean- ing c ...
-
Audiovox LCM5043NP - page 15
REMOTE CONTROLLER NOTE : The Remote Controller supplied with this system is a stan- dard remote control, which is used to operate other systems. The Remote Controller is not a universal remote and will only perform the functions described herein. Only the Keys highlighted on the Remote Controller image bellow are used to operate this system. Functi ...
-
Audiovox LCM5043NP - page 16
15 MENU FUNCTION KEY : The MENU Key is used to navigate between the Color , Brightness and Tint adjustment modes. When the MENU Key is pressed an On Screen Display(OSD) will appear as shown bellow . OSD Press release and tap the MENU Key until the desired adjustment mode is selected. T o return to the original set- tings select the RESET . When an ...
-
Audiovox LCM5043NP - page 17
16 NOTE: For the LCM5643NP - Select either * NTSC or P AL, press the p or q Keys ( CH/DISK/SET ). VOLUME CONTROL KEY : T o switch between Video Input Sources (A V1 and A V2) press and release the MODE Key . VIDEO SOURCE MODE KEY : T o increase or decrease the V olume, press and hold the VOL p or q Key until the desired volume is reached. ...
-
Audiovox LCM5043NP - page 18
17 Replacement of Remote Controller Battery: 1. Use a small coin to pry open battery holder from compartment. 2. Remove old battery and put in a new one with positive sign “ + “ facing upward. 3. Push compartment into position. Precaution: 1. Dispose off used battery properly . 2. Do not misuse battery by short - circuiting the “ + “ and ? ...
-
Audiovox LCM5043NP - page 19
18 LCM5043NP: LCD Panel Size (Diagonal) ................................... 5 " LCD Panel Format ................................................. 960 x 234 dots LCD Panel Resolution ........................................... 224,640 pixels LCD Backlight Life ................................................. 10,000 hrs Image Aspect Ratio .... ...
-
Audiovox LCM5043NP - page 20
© 2002 Audiovox Electronics Corp., Hauppauge, NY 128-6323 AUDIOVOX ELECTRONICS CORP. (the Company) warrants to the original retail purchaser of this product that should this product or any part thereof, under normal use and conditions, be proven defective in material or workmanship within 36 months from the date of original purchase, such defect(s ...
Hai una domanda su Audiovox LCM5043NP?
Utilizza il modulo sottostante
Se non hai risolto il problema con Audiovox LCM5043NP con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Audiovox LCM5043NP è probabile che voglia condividere il modo di risolverlo.