Manuale per l’uso Cisco Systems 7600

28 pagine 0.22 mb
Scarica

Vai alla pagina of 28

Summary
  • Cisco Systems 7600 - page 1

    CHAPTER 2-1 Cisco 7600 Optical Services Router Quick Software Configuration Guide 78-12799-01 2 Basic MSFC Software Configuration This chapter provides the basic Multilayer Switch Feature Card 2 (MSFC2) conf iguration information for the Cisco 7600 Optical Services Router (OSR). For more detailed conf iguration information, refer to the software co ...

  • Cisco Systems 7600 - page 2

    Chapter 2 Basic MSFC Software Configuration Configuring the MSFC2 2-2 Cisco 7600 Optical Services Router Quick Software Configuration Guide 78-12799-01 T o access the MSFC2 from the supervisor engine, enter the session command in privile ged mode: Console> session 15 Trying Router-15... Connected to Router-15. Escape character is '^]'. ...

  • Cisco Systems 7600 - page 3

    2-3 Cisco 7600 Optical Services Router Quick Software Configuration Guide 78-12799-01 Chapter 2 Basic MSFC Software Configuration Configuring the MSFC2 • Using the global conf iguration mode If you do not want to use the interacti ve script of the setup facility to conf igure your router , you can conf igure your router manually using the global ...

  • Cisco Systems 7600 - page 4

    Chapter 2 Basic MSFC Software Configuration Configuring the MSFC2 2-4 Cisco 7600 Optical Services Router Quick Software Configuration Guide 78-12799-01 When you enter the setup command at the pri vileged EXEC mode prompt (assuming that the POS interface has been pre viously conf igured and you are being queried by the system for changes), you will ...

  • Cisco Systems 7600 - page 5

    2-5 Cisco 7600 Optical Services Router Quick Software Configuration Guide 78-12799-01 Chapter 2 Basic MSFC Software Configuration Configuring the MSFC2 Bridging software. X.25 software, Version 3.0.0. SuperLAT software (copyright 1990 by Meridian Technology Corp). TN3270 Emulation software. 1 POS controller (4 POS). 1 Virtual Ethernet/IEEE 802.3 in ...

  • Cisco Systems 7600 - page 6

    Chapter 2 Basic MSFC Software Configuration Configuring the MSFC2 2-6 Cisco 7600 Optical Services Router Quick Software Configuration Guide 78-12799-01 This display sho ws that no interfaces ha ve been conf igured: Interface IP-Address OK? Method Status Protocol Ethernet0 unassigned YES unset administratively down down POS3/0 unassigned YES unset a ...

  • Cisco Systems 7600 - page 7

    2-7 Cisco 7600 Optical Services Router Quick Software Configuration Guide 78-12799-01 Chapter 2 Basic MSFC Software Configuration Configuring the MSFC2 Step 5 Enter the enable password when prompted to do so: The enable password is used when there is no enable secret and when using older software and some boot images. Enter enable password: wilma F ...

  • Cisco Systems 7600 - page 8

    Chapter 2 Basic MSFC Software Configuration Configuring the MSFC2 2-8 Cisco 7600 Optical Services Router Quick Software Configuration Guide 78-12799-01 Specify the IGRP autonomous system number as follows: Configure IP? [yes]: yes Configure IGRP routing? [yes]: yes Your IGRP autonomous system number [1]: 199 Step 8 Enter yes or no to the following ...

  • Cisco Systems 7600 - page 9

    2-9 Cisco 7600 Optical Services Router Quick Software Configuration Guide 78-12799-01 Chapter 2 Basic MSFC Software Configuration Configuring the MSFC2 Configuring global parameters: Enter host name: Router Enter enable secret: barney Enter enable password: wilma Enter virtual terminal password: bambam Configure IP?: yes Configure IGRP routing?: ye ...

  • Cisco Systems 7600 - page 10

    Chapter 2 Basic MSFC Software Configuration Configuring the MSFC2 2-10 Cisco 7600 Optical Services Router Quick Software Configuration Guide 78-12799-01 These sections describe how to conf igure the Layer 3 interfaces on the modules installed in the Cisco 7600 OSR: • Conf iguring the Gigabit Ethernet Interfaces, page 2-10 • Conf iguring the POS ...

  • Cisco Systems 7600 - page 11

    2-11 Cisco 7600 Optical Services Router Quick Software Configuration Guide 78-12799-01 Chapter 2 Basic MSFC Software Configuration Configuring the MSFC2 IP address for this interface: 2.1.1.1 Number of bits in subnet field: 0 Class A network is 2.0.0.0, 0 subnet bits; mask is 255.0.0.0 Configure CLNS on this interface?: yes Note For POS interfaces, ...

  • Cisco Systems 7600 - page 12

    Chapter 2 Basic MSFC Software Configuration Configuring the MSFC2 2-12 Cisco 7600 Optical Services Router Quick Software Configuration Guide 78-12799-01 Answer yes if you want to sa ve the running conf iguration f ile to NVRAM and display the following additional output: Use this configuration? [yes/no]: yes [OK] Use the enabled mode 'configur ...

  • Cisco Systems 7600 - page 13

    2-13 Cisco 7600 Optical Services Router Quick Software Configuration Guide 78-12799-01 Chapter 2 Basic MSFC Software Configuration Configuring the MSFC2 When you enter the show version command, the follo wing typical display appears: Router# show version Cisco Internetwork Operating System Software IOS (tm) MSFC2 Software (C6MSFC2-JSV-M), Version 1 ...

  • Cisco Systems 7600 - page 14

    Chapter 2 Basic MSFC Software Configuration Using the Global Configuration Mode 2-14 Cisco 7600 Optical Services Router Quick Software Configuration Guide 78-12799-01 Using the Global Configuration Mode If you prefer not to use the interacti ve script of the setup f acility , you can manually conf igure the Cisco 7600 OSR using the global conf igur ...

  • Cisco Systems 7600 - page 15

    2-15 Cisco 7600 Optical Services Router Quick Software Configuration Guide 78-12799-01 Chapter 2 Basic MSFC Software Configuration Verifying the Running Configuration Settings Step 4 Sav e your conf iguration settings, as described in the “Saving the Running Conf iguration Settings to NVRAM” section on page 2-19 . Y our router is now minimally ...

  • Cisco Systems 7600 - page 16

    Chapter 2 Basic MSFC Software Configuration Verifying the Running Configuration Settings 2-16 Cisco 7600 Optical Services Router Quick Software Configuration Guide 78-12799-01 version 12.1 no service pad service timestamps debug uptime service timestamps log uptime no service password-encryption ! hostname Router ! ! interface GigabitEthernet5/1 no ...

  • Cisco Systems 7600 - page 17

    2-17 Cisco 7600 Optical Services Router Quick Software Configuration Guide 78-12799-01 Chapter 2 Basic MSFC Software Configuration Verifying the Running Configuration Settings no service pad no service udp-small-servers no service tcp-small-servers ! hostname Router ! enable secret 5 $1$W6K5$W/p5Bq6IPLGJ/hS9VVP1g. enable password lab interface POS7 ...

  • Cisco Systems 7600 - page 18

    Chapter 2 Basic MSFC Software Configuration Verifying the Running Configuration Settings 2-18 Cisco 7600 Optical Services Router Quick Software Configuration Guide 78-12799-01 ! version 12.1. no service pad no service udp-small-servers no service tcp-small-servers ! hostname Router -----------! enable password lab ! no ip domain-lookup ip host ray ...

  • Cisco Systems 7600 - page 19

    2-19 Cisco 7600 Optical Services Router Quick Software Configuration Guide 78-12799-01 Chapter 2 Basic MSFC Software Configuration Reviewing the Running Configuration Settings interface POS6/0 ip address 12.1.1.1 255.255.255.0 crc 32 ! Saving the Running Configuration Settings to NVRAM T o sav e the running conf iguration settings to NVRAM, enter t ...

  • Cisco Systems 7600 - page 20

    Chapter 2 Basic MSFC Software Configuration Reviewing the Running Configuration Settings 2-20 Cisco 7600 Optical Services Router Quick Software Configuration Guide 78-12799-01 interface POS3/0 ip address 2.1.1.1 255.0.0.0 no keepalive crc 16 no cdp enable ! interface POS3/1 ip address 2.1.1.2 255.0.0.0 no keepalive crc 16 no cdp enable ! interface ...

  • Cisco Systems 7600 - page 21

    2-21 Cisco 7600 Optical Services Router Quick Software Configuration Guide 78-12799-01 Chapter 2 Basic MSFC Software Configuration Performing Other Configuration Tasks no ip classless ip route 2.5.4.254 255.255.255.255 Ethernet0 ! map-list atm1 ip 1.1.1.1 atm-vc 1 ip 1.1.1.3 atm-vc 2 ip 1.1.1.4 atm-vc 4 ip 15.0.0.1 atm-vc 3 ip 15.0.0.5 atm-vc 10 ip ...

  • Cisco Systems 7600 - page 22

    Chapter 2 Basic MSFC Software Configuration Performing Other Configuration Tasks 2-22 Cisco 7600 Optical Services Router Quick Software Configuration Guide 78-12799-01 Configuring the Software Configuration Register The software conf iguration register is a 16-bit register in NVRAM that you use to def ine specif ic system parameters.Y ou can set or ...

  • Cisco Systems 7600 - page 23

    2-23 Cisco 7600 Optical Services Router Quick Software Configuration Guide 78-12799-01 Chapter 2 Basic MSFC Software Configuration Performing Other Configuration Tasks Configuring Boot Field Settings and Using the Boot Command The four lo w-order bits of the software conf iguration register (bits 3, 2, 1, and 0) form a boot f ield that def ines the ...

  • Cisco Systems 7600 - page 24

    Chapter 2 Basic MSFC Software Configuration Performing Other Configuration Tasks 2-24 Cisco 7600 Optical Services Router Quick Software Configuration Guide 78-12799-01 T o create this f ilename, the system starts with the name cisco and links the octal equiv alent of the boot f ield value and the processor type in this format: cisco<bootfieldval ...

  • Cisco Systems 7600 - page 25

    2-25 Cisco 7600 Optical Services Router Quick Software Configuration Guide 78-12799-01 Chapter 2 Basic MSFC Software Configuration Performing Other Configuration Tasks Step 4 Exit the global conf iguration mode by pressing Ctrl-Z or entering the end command: Router(config)# config-register 0xvalue Router(config)# end Router# The new contents of the ...

  • Cisco Systems 7600 - page 26

    Chapter 2 Basic MSFC Software Configuration Performing Other Configuration Tasks 2-26 Cisco 7600 Optical Services Router Quick Software Configuration Guide 78-12799-01 If you set the boot f ield value to 0, you must boot the system manually by entering the boot command at the R OM monitor prompt (rommon>). If you set the boot f ield value to 0x2 ...

  • Cisco Systems 7600 - page 27

    2-27 Cisco 7600 Optical Services Router Quick Software Configuration Guide 78-12799-01 Chapter 2 Basic MSFC Software Configuration Performing Other Configuration Tasks Step 3 Enter the show version command at the pri vileged EXEC mode prompt to display the current software conf iguration register setting: Router# show version . . . Make a note of t ...

  • Cisco Systems 7600 - page 28

    Chapter 2 Basic MSFC Software Configuration Performing Other Configuration Tasks 2-28 Cisco 7600 Optical Services Router Quick Software Configuration Guide 78-12799-01 After the interface conf iguration information is displayed, the user EXEC mode prompt appears: Router> Step 10 Enter the enable command at the user EXEC mode prompt to enter the ...

Fabbricante Cisco Systems Categoria Network Router

I documenti che otteniamo dal fabbricante del dispositivoCisco Systems 7600 possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Cisco Systems
- manuali per l’uso 7600
- schede prodotto Cisco Systems
- opuscoli
- o etichette energetiche Cisco Systems 7600
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Cisco Systems 7600.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Cisco Systems 7600, manuali di manutenzione, brevi manuali o manuali utente Cisco Systems 7600. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Cisco Systems 7600.

Manuali per l’uso simili

Manuale completo del dispositivo Cisco Systems 7600, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Cisco Systems 7600 dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Cisco Systems 7600.

Il manuale per l’uso completo Cisco Systems, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Cisco Systems 7600 - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Cisco Systems 7600, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Cisco Systems 7600 che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Cisco Systems 7600 - che ci dovrebbe aiutare nei primi passi durante l'uso Cisco Systems 7600
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Cisco Systems 7600
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Cisco Systems 7600 in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Cisco Systems 7600?

Utilizza il modulo sottostante

Se non hai risolto il problema con Cisco Systems 7600 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Cisco Systems 7600 è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Commenti (0)