Italiano dropdown-ico

Manuale per l’uso Hotpoint JB400DP1BB

57 pagine 2.73 mb
Scarica

Vai alla pagina of 57

Summary
  • Hotpoint JB400DP1BB - page 1

    GE JB400 Steam Clean Range Range Models: JB400DP1WW JB400DP1BB JB400SPSS ...

  • Hotpoint JB400DP1BB - page 2

    2 Copyright 2009 IMPORTANT SAFETY NOTICE The information in this presentation is intended for use by individuals possessing adequate backgrounds of electrical, electronic, & mechanical experience. Any attempt to repair a major appliance may result in personal injury & property damage. The manufacturer or seller cannot be responsible for the ...

  • Hotpoint JB400DP1BB - page 3

    3 Copyright 2009 GE Factory Service Employees are required to use safety glasses with side shields, cut resistant (Dyneema ® ) gloves & steel toe shoes for all repairs. Dyneema® Cut Resistant Glove Safety Glasses must be compliant wi th ANSI Z87.1-2003 Prescription Safety Glasses Plano Safety Glasses Steel Toe Shoes ...

  • Hotpoint JB400DP1BB - page 4

    4 Copyright 2009 Warranty ...

  • Hotpoint JB400DP1BB - page 5

    5 Copyright 2009 Nomenclature J B 400 D P 1 WW J = GE ...

  • Hotpoint JB400DP1BB - page 6

    6 Copyright 2009 Model / Serial Number Plate • Mini-Manual is in an envelope and located inside the left hand panel. Model / serial plate is located on the front frame behind the storage drawer. ...

  • Hotpoint JB400DP1BB - page 7

    7 Copyright 2009 Anti-Tip Bracket * Range must be secured by the Anti-Tip Bracket supplied. ...

  • Hotpoint JB400DP1BB - page 8

    8 Copyright 2009 Oven Door Removal • Fully open the door. • Push the hinge locks down toward the door frame, to the unlocked position. This may require a flat blade screwdriver. ...

  • Hotpoint JB400DP1BB - page 9

    9 Copyright 2009 Oven Door Removal • Close door to the door removal position. • Firmly grasp both sides of the door at the top. • Lift door up until the hinge arm is clear of the slot. ...

  • Hotpoint JB400DP1BB - page 10

    10 Copyright 2009 Oven Door Re-Installation • Firmly grasp both sides of the door at the top. • With the door at the same angle as the removal position, seat the indentation of the hinge arm into the bottom edge of the hinge slot. ...

  • Hotpoint JB400DP1BB - page 11

    11 Copyright 2009 Oven Door Re-Installation • Fully open the door. • Push the hinge locks up against the front frame of the oven cavity, to the locked position. • Close the oven door. ...

  • Hotpoint JB400DP1BB - page 12

    12 Copyright 2009 Door Gasket Door gasket attached with spring clips around perimeter of door. ...

  • Hotpoint JB400DP1BB - page 13

    13 Copyright 2009 Door Gasket A gap must be left in the gasket at the bottom of the door. The gap is r equired to provide air flow in the oven for proper baking results. ...

  • Hotpoint JB400DP1BB - page 14

    14 Copyright 2009 Door Switch Door switch is merely a s ensor input to the control. It allows the control to know the stat us of the door position, open or closed. Has no control over the oven light operation. ...

  • Hotpoint JB400DP1BB - page 15

    15 Copyright 2009 Door Switch Replacement After lifting cooktop, switch a ssembly can be released by removing two ¼” hex heads securing it to the front frame of the oven. ...

  • Hotpoint JB400DP1BB - page 16

    16 Copyright 2009 Cooktop • Open oven door. • Remove two ¼” hex head screws se curing cooktop to front frame. • Lift cooktop. • Use prop to support cooktop, if desired. ...

  • Hotpoint JB400DP1BB - page 17

    17 Copyright 2009 Cooktop Elements 6 Inch 1500W 6 Inch 1500W 8 Inch 2000W 10 Inch 3000W Inner – 1400W Outer – 1600W ...

  • Hotpoint JB400DP1BB - page 18

    18 Copyright 2009 Cooktop Element Replacement After marking the numbered holes on the burner outer case, lift up on spring clip to disengage it from the burner. ...

  • Hotpoint JB400DP1BB - page 19

    19 Copyright 2009 Cooktop Element Replacement • After removing hex head from “L” bracket, remove bracket. • Disengage mounting clips from burner case. • Mark and remove wires from terminals. • Lift and remove burner from cooktop assembly ...

  • Hotpoint JB400DP1BB - page 20

    20 Copyright 2009 Temperature Limit / Hot Cooktop Light Switch The temperature limit/hot cooktop li ght switch performs two functions: 1. Turns on the Hot Cooktop Light when the surface unit switch is turned on. The hot light will remain on until the glass surface above the heating unit has cooled below 150°F (even after the surface unit switch ha ...

  • Hotpoint JB400DP1BB - page 21

    21 Copyright 2009 Temperature Limit / Hot Cooktop Light Switch The temperature limit/hot cooktop li ght switch performs two functions: 2. Detects when glass temperature a bove a unit has exceeded it’s limit of approximately 1031°F and disconnects power to that unit. When the glass temperature cools below 1031°F , the unit will turn back on. * T ...

  • Hotpoint JB400DP1BB - page 22

    22 Copyright 2009 Cooktop Removal • Begin by disconnecting two power plugs at rear of cooktop area. • Next, remove ground wire screw at bottom of cooktop. ...

  • Hotpoint JB400DP1BB - page 23

    23 Copyright 2009 Cooktop Removal • Return cooktop to normally closed position. • Lift rear of cooktop @ two inches. • Pull cooktop towards front of range to disengage hinge slots on cooktop from hinge pins on frame. ...

  • Hotpoint JB400DP1BB - page 24

    24 Copyright 2009 Control Panel Removal The control panel contains the ER C & the infinite heat switches. To Service: 1. Remove 3 ¼” hex heads at the top, in the back of the range. 2. Remove 2 Phillips screws under the control panel in the front of the range. ...

  • Hotpoint JB400DP1BB - page 25

    25 Copyright 2009 Control Panel Removal 3. Pull bottom of panel out while lifting panel up. 4. Lay panel on cooking surface. CAUTION: Place a protective coveri ng (such as a towel) between the control panel and the cooking surfac e to avoid damage to either. ...

  • Hotpoint JB400DP1BB - page 26

    26 Copyright 2009 Oven Sensor • Oven sensor should read @ 1100 Ω at room temperature. • Resistance can be read at the ERC plug (white wires) pins 1 & 2 or it can be read at the sensor disconnect plug behind the range. ...

  • Hotpoint JB400DP1BB - page 27

    27 Copyright 2009 Oven Sensor Oven sensor disconnect plug. ...

  • Hotpoint JB400DP1BB - page 28

    28 Copyright 2009 T09 Control - ERC The T09 Control System consists of the control, the key panel and the oven sensor. (Control & key panel are a single component). 2:31 ...

  • Hotpoint JB400DP1BB - page 29

    29 Copyright 2009 Display On / Off Feature 3:02 Note: the clock display will go blank if the UP and DOWN arrows are pressed at the same time for 1 sec or less. If the customer complains that there is no time of day clock on the range, have them press the UP and DOWN arro ws to have the clock re-appear ...

  • Hotpoint JB400DP1BB - page 30

    30 Copyright 2009 Special Functions SF ...

  • Hotpoint JB400DP1BB - page 31

    31 Copyright 2009 T09 Control – ERC Removal • To remove ERC from backsplash, remove 4 ¼” hex heads securing ERC to backsplash frame. • Remove ERC from frame. ...

  • Hotpoint JB400DP1BB - page 32

    32 Copyright 2009 T09 Control - ERC 2 white – Sensor Orange / Yellow – Door Switch Neutral Oven Light Bake Element Broil Element L1 L2 Bake & Broil Common ...

  • Hotpoint JB400DP1BB - page 33

    33 Copyright 2009 Key Panel Test Depress each pad on the key panel individually. If the key panel is functioning properly, the following should occur: • Bake, Broil, Steam Clean, Kitchen Timer, Cooking Time – Audible tone and display showing mode of operation selected. • Start/On, Clear/Off – Audible tone and display shows time of day. • ...

  • Hotpoint JB400DP1BB - page 34

    34 Copyright 2009 Control Voltage - ERC ...

  • Hotpoint JB400DP1BB - page 35

    35 Copyright 2009 Fault Codes --3 F-code Retrieval Mode Function Key (s) Conditions & Response Code retrieval to display Kitchen Timer + Up + Down Fault codes displayed Clear codes Kitchen Timer + Clock Fault codes cleared Exit mode Clear/Off Return to normal operation ...

  • Hotpoint JB400DP1BB - page 36

    36 Copyright 2009 Fault Codes ...

  • Hotpoint JB400DP1BB - page 37

    37 Copyright 2009 Steam Clean Operation 0:30 ...

  • Hotpoint JB400DP1BB - page 38

    38 Copyright 2009 Steam Clean Procedure To begin the steam cycle: 1. Remove racks and accessories from the oven cavity. Do not place cookware or other items in the oven during the Steam Clean cycle. 2. Pour 1 cup (8 oz.) of room temperature water onto the recessed area of the oven bottom. Do not add cleaning solutions or chemicals of any kind to th ...

  • Hotpoint JB400DP1BB - page 39

    39 Copyright 2009 Steam Clean Procedure 0:30 4. Press the Steam Clean pad; then press Start/On. 5. A 30-minute cycle will begin to count down on the display. 6. When the Steam Clean cycle is co mplete, the oven control will beep and the Steam Clean light will blink. Press the Clear/Off pad. ...

  • Hotpoint JB400DP1BB - page 40

    40 Copyright 2009 Steam Clean Procedure 7. The oven bottom and remaining water will still be very warm at the end of the cycle. This is normal. 8. Remove soils using a scrub brush or nylon scouring pad. A soap filled steel wool pad may be used only on the porcelain oven interior. The use of abrasive pads will scratch the door glass. Do not wipe soi ...

  • Hotpoint JB400DP1BB - page 41

    41 Copyright 2009 Steam Clean Procedure – IMPORTANT NOTES • If a steam clean cycle is initia ted without water, press the Clear/Off pad to end the cycle. Wait for the range to cool to room temperature before pouri ng water into the recessed area and initiating another st eam cycle. • Do not open the door during the Steam Clean cycle. An error ...

  • Hotpoint JB400DP1BB - page 42

    42 Copyright 2009 Hidden Bake Element • If a problem is suspected with the hi dden bake element, check for proper resistance at the rear of the ERC or at the yellow / orange wire disconnect plug before range disassembly. • Resistance between orange and yellow wires to element should be @ 20 Ω . ...

  • Hotpoint JB400DP1BB - page 43

    43 Copyright 2009 Hidden Bake Element • If element requires replacement, r ange left side panel needs to be removed. • Begin by removing the hidden screw at bottom front after removing storage drawer. ...

  • Hotpoint JB400DP1BB - page 44

    44 Copyright 2009 Hidden Bake Element After lifting or removing cooktop, remove two ¼” hex heads and a single Phillips screw from the top of the side panel. ...

  • Hotpoint JB400DP1BB - page 45

    45 Copyright 2009 Hidden Bake Element Next, remove 3 ¼” hex heads from rear of left side panel. ...

  • Hotpoint JB400DP1BB - page 46

    46 Copyright 2009 Hidden Bake Element Finally, grasp panel and lift @ an inch to releas e tabs on the side of the frame from openings in the side panel. ...

  • Hotpoint JB400DP1BB - page 47

    47 Copyright 2009 Hidden Bake Element Carefully, lift insulation blanket and temporarily tuck it under upper frame to clear work area. ...

  • Hotpoint JB400DP1BB - page 48

    48 Copyright 2009 Hidden Bake Element Push down on insulation retainer to clear it from the bake element compartment opening. ...

  • Hotpoint JB400DP1BB - page 49

    49 Copyright 2009 Hidden Bake Element • Remove orange and yellow leads from bake element terminals. • Remove two ¼” hex heads securing element compartment cover to frame. ...

  • Hotpoint JB400DP1BB - page 50

    50 Copyright 2009 Hidden Bake Element Fold out or completely remove compartment cover to access hidden bake element. ...

  • Hotpoint JB400DP1BB - page 51

    51 Copyright 2009 Hidden Bake Element Slide out element from compartment to remove. ...

  • Hotpoint JB400DP1BB - page 52

    52 Copyright 2009 Hidden Bake Element Upon re-insertion of bake element, t abs on assembly must align with slots or openings on the far side of the compartment. ...

  • Hotpoint JB400DP1BB - page 53

    53 Copyright 2009 Oven Light Oven lighting consists of a single 40w, incandescent bulb with a clear glass cover held in place with a spring wire. ...

  • Hotpoint JB400DP1BB - page 54

    54 Copyright 2009 Strip Circuits ...

  • Hotpoint JB400DP1BB - page 55

    55 Copyright 2009 Schematic ...

  • Hotpoint JB400DP1BB - page 56

    56 Copyright 2009 Wiring Diagram ...

  • Hotpoint JB400DP1BB - page 57

    57 Copyright 2009 END OF PRESENTATION ...

Fabbricante Hotpoint Categoria Range

I documenti che otteniamo dal fabbricante del dispositivoHotpoint JB400DP1BB possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Hotpoint
- manuali per l’uso JB400DP1BB
- schede prodotto Hotpoint
- opuscoli
- o etichette energetiche Hotpoint JB400DP1BB
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Hotpoint JB400DP1BB.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Hotpoint JB400DP1BB, manuali di manutenzione, brevi manuali o manuali utente Hotpoint JB400DP1BB. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Hotpoint JB400DP1BB.

Manuali per l’uso simili

Manuale completo del dispositivo Hotpoint JB400DP1BB, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Hotpoint JB400DP1BB dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Hotpoint JB400DP1BB.

Il manuale per l’uso completo Hotpoint, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Hotpoint JB400DP1BB - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Hotpoint JB400DP1BB, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Hotpoint JB400DP1BB che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Hotpoint JB400DP1BB - che ci dovrebbe aiutare nei primi passi durante l'uso Hotpoint JB400DP1BB
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Hotpoint JB400DP1BB
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Hotpoint JB400DP1BB in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Hotpoint JB400DP1BB?

Utilizza il modulo sottostante

Se non hai risolto il problema con Hotpoint JB400DP1BB con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Hotpoint JB400DP1BB è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)