Manuale per l’uso Whirlpool 188414

15 pagine 4.86 mb
Scarica

Vai alla pagina of 15

Summary
  • Whirlpool 188414 - page 1

    PAG E T able Of Contents Water Heater Safety .......................................................................... 2 Installing Your Electric Water Heater ................................................ 3-8 Unpacking Instructions ................................................................ 3 Location Requirements ......................... ...

  • Whirlpool 188414 - page 2

    2 The California Safe Drinking Water and T oxic Enforcement Act requires the Governor of California to publish a list of substances known to the State of California to cause cancer , birth defects, or other reproductive harm, and requires businesses to warn of potential exposure to such substances. Warning: This product contains a chemical known to ...

  • Whirlpool 188414 - page 3

    Consumer Information National Fire Protection Agency 1 Batterymarch Park Quincy, MA 02269 American National Standards Institute 1430 Broadway New Y ork, NY 10018 Check your phone listings for the local authorities having jurisdiction over your installation. Consumer Responsibilities A data plate identifying your water heater can be found adjacent t ...

  • Whirlpool 188414 - page 4

    Location Requirements Site location Select a location near the center of the water piping system. It must be installed indoors and in a vertical position on a level surface. The water heater should be located in an area not subject to freezing temperatures. Water heaters located in unconditioned spaces (i.e., attics, basements, etc.) may require th ...

  • Whirlpool 188414 - page 5

    5 Water System Piping Piping Installation Piping, fittings, and valves should be installed according to the installation drawing (Figure 2). If the indoor installation area is subject to freezing temperatures, the water piping must be protected by insulation. Water supply pressure should not exceed 80% of the working pressure of the water heater. T ...

  • Whirlpool 188414 - page 6

    T emperature and Pressure Relief Valve For protection against excessive pressures and temperatures, a temperature and pressure relief valve must be installed in the opening marked “T & P RELIEF VAL VE” (See Figure 5). Caution: T o reduce the risk of excessive pressures and temperatures in this water heater, install temperature and pressure ...

  • Whirlpool 188414 - page 7

    Important: Only a new temperature and pressure relief valve should be used with your water heater. Do not use an old or existing valve as it may be damaged or not adequate for the working pressure of the new water heater. Do not place any valve between the relief valve and the tank. The Temperature & Pressure Relief V alve: ! Must be connected ...

  • Whirlpool 188414 - page 8

    Installation Checklist Water Heater Location ! Centrally located with the water piping system. ! Located indoors and in a vertical position. ! Protected from freezing temperatures. ! Provisions made to protect the area from water damage. ! Drain pan installed and piped into an adequate drain. ! Sufficient clearance to service the water heater. Wate ...

  • Whirlpool 188414 - page 9

    Important: Operation of this water heater without access doors or insulation could result in much higher water temperatures than the desired set point, increasing the risk of scald injury. Do not operate water heater with the access doors or insulation removed. Access Doors Water Heater St art-Up 1. Before operating the water heater, make sure the ...

  • Whirlpool 188414 - page 10

    Figure 7 Temperature Control System Water T emperature Adjustment The water temperature can be adjusted from 80°F to 150°F . Use the temperature control knob to change to the desired temperature. Operating Mode Descriptions 1. Smart Mode - The controller operates the water heater to maintain the customer’s selected temperature. 2. Energy Smart ...

  • Whirlpool 188414 - page 11

    11 Operation Conditions Anode Rod/Water Odor Each water heater contains at least one anode rod, which will slowly deplete while protecting the glass-lined tank from corrosion and prolonging the life of the water heater. Certain water conditions will cause a reaction between this rod and the water. Once the anode is depleted, the tank will start to ...

  • Whirlpool 188414 - page 12

    12 Draining and Flushing It is recommended that the tank be drained and flushed every 6 months to remove sediment which may buildup during operation. T o drain the tank perform the following steps: 1. Turn off the power to water heater . 2. Close the cold water inlet valve and open a nearby hot water faucet. 3. Connect a hose to the drain valve and ...

  • Whirlpool 188414 - page 13

    7. Close the drain valve. Open the nearest hot water faucet and allow the tank to fill completely with water. T o purge the lines of any excess air and sediment, keep the hot water faucet open for 3 minutes after a constant flow of water is obtained. 8. Check for leaks around the element(s). 9. Connect the electric wires to the heater element. Make ...

  • Whirlpool 188414 - page 14

    14 Diagnostic Code Chart DIAGNOSTIC LIGHT CORRECTIVE ACTION * LIGHT ON INDICATES No power to control board or diagnostic light burned out Normal operation NO LIGHT 1 FLASH 2 FLASHES Power on with no water in tank Water temperature exceeded high limit 3 FLASHES Sensor failure 4 FLASHES Upper element circuit failure 1. Remove power 2. Check element c ...

  • Whirlpool 188414 - page 15

    15 © 2003 American W ater Heater Company . All Rights Res erved. Printed in the U.S.A. ® Registered trademark/TM Trademark of Whirlpool, U.S.A ENERGY SMART is a trademark of American W ater Heater Company used under license. Repair Parts Repair parts may be ordered through your plumber, local distributor, home improvement center , or by calling 1 ...

Fabbricante Whirlpool Categoria Water Heater

I documenti che otteniamo dal fabbricante del dispositivoWhirlpool 188414 possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Whirlpool
- manuali per l’uso 188414
- schede prodotto Whirlpool
- opuscoli
- o etichette energetiche Whirlpool 188414
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Whirlpool 188414.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Whirlpool 188414, manuali di manutenzione, brevi manuali o manuali utente Whirlpool 188414. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Whirlpool 188414.

Manuale completo del dispositivo Whirlpool 188414, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Whirlpool 188414 dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Whirlpool 188414.

Il manuale per l’uso completo Whirlpool, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Whirlpool 188414 - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Whirlpool 188414, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Whirlpool 188414 che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Whirlpool 188414 - che ci dovrebbe aiutare nei primi passi durante l'uso Whirlpool 188414
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Whirlpool 188414
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Whirlpool 188414 in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Whirlpool 188414?

Utilizza il modulo sottostante

Se non hai risolto il problema con Whirlpool 188414 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Whirlpool 188414 è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Commenti (0)