-
Troy-Bilt 430 Series - page 1
IMPOR T ANT : Read saf ety rules and instr uctions carefully bef ore operating equipment. 21” Rear & Side Dischar ge Mulching La wn Mower Model Series 430 PRINTED IN U.S .A. Warning: This unit is equipped with an internal co mbustion engine and should not be used on or near any unimpro ved forest- covered, brush-covered or gras s-covered land ...
-
Troy-Bilt 430 Series - page 2
2 TABLE OF CONTENTS FINDING MODEL NUMBER This Operator’s Manual is an import ant part of your new lawn mower. It will help you asse mble, prepare and maintain the unit fo r best perform ance. Please read and understand what it says. Before you star t assembling your new equipment , please locate the model plate on the equipment and copy th e info ...
-
Troy-Bilt 430 Series - page 3
3 SECTION 1: IMPORTANT SAFE OPERATION PRACTICES General Oper ation 1. Read this operator’s man ual carefully in its entirety before atte mpting to assemble t his machine. Read, understand, and follow all instruct ions on the machine and in the manua l(s) before operat ion. Be completely familiar with th e controls an d the proper use of this mach ...
-
Troy-Bilt 430 Series - page 4
4 8. Never operate th e mower in wet grass. Always be sure of your footing. A slip and fall can cause serious personal injury. If yo u feel you are losing your footing, release the b lade control ha ndle immediately and th e blade will stop rotating within three seconds. 9. Mow in daylight or good artificial ligh t. Walk, never run. Stop the blade ...
-
Troy-Bilt 430 Series - page 5
5 7. Extinguish all cigarettes, ciga rs, pipes and other sources of ignition . 8. Never fuel machine indoors because flamma ble vapors will accumula te in the area. 9. Never remove gas ca p or add fuel while the engine is hot or running. Allow engine to co ol at least two minutes befo re refueling. 10. Never over fill fuel tank. Fill tank to no mor ...
-
Troy-Bilt 430 Series - page 6
6 SECTION 2: SLOPE GAUGE 15° SIGHT AND HOLD THIS LEVEL WITH A VERTICAL TREE A POWER POLE A CORNER OF A BUILDING OR A FENCE POST F O L D ON D O T T E D L I N E , R E P R E S E N T I N G A 1 5 ° S L OP E USE THIS PAGE AS A GUIDE TO DETERMINE SLOPES WHERE YOU MAY NOT O PERATE SAFELY. Do not mow on inclines wit h a slope in excess of 15 degree s (a r ...
-
Troy-Bilt 430 Series - page 7
7 SECTION 3: ASSEMBLING YOUR LAWN MOWER Removing Unit From Carton • Remove sta ples, break glue on top flaps or cut tape at carton end and peel t op flap to open carton. • Remove loose parts if included with unit. • Cut corner s and lay carton down fla t. Remove packing material. • Roll or slide unit ou t of carton. Check ca rton thoroughly ...
-
Troy-Bilt 430 Series - page 8
8 • Fasten the cable to the lo wer handle with the t wo cable ties fou nd on the lower handle. Pull the ca ble ties tight an d trim off the e xcess. See Figure 4 . Figure 4 Attaching Starter Rope • The rope guide is at tached to the right side of upper handle. Loosen the wing nut which secu res the rope guide. See Figure 5. • With the spark p ...
-
Troy-Bilt 430 Series - page 9
9 Converting to Side-Dischar ge • Your mower has been shipped as a m ulcher. To convert it to a side-dischar ge mower, lift the mulching plug. Slide the two hooks on the side- discharge deflector under the h inge pin on the mulching plug assembly. Lo wer the mulching plug. See Figure 9 . Figure 9 • Do not remov e the side mulching plug at any t ...
-
Troy-Bilt 430 Series - page 10
10 Cutting Height Adjustment Lever This lever, located at each wheel, lets you adju st cutting height of the grass. Reme mber to put all four levers at the same height to avoid une ven cut. Throttle Control The engine is equipped wit h a constant speed throttle for maximum engine and cu tting perfo rmance. Recoil Starter The recoil star ter is atta ...
-
Troy-Bilt 430 Series - page 11
11 Operating Y our Lawn Mower • Once the engine has star ted, squeeze th e blade control handle agai nst the upper handle to r un the lawn mower. • Do not operate the mower withou t the mulching cover, the grass catcher b ag, or the disc harge chute prope rly installed. • Be sure that the lawn is cle ar of stones, st icks, wire, or other obje ...
-
Troy-Bilt 430 Series - page 12
12 SECTION 6: MAINTAINING YOUR LAWN MOWER Cleaning the Lawn Mower • Clean underside of th e mower deck after each use to prevent any build- up of grass. If this debris accumulates, it will cause rust and corrosion. NOTE: We do not recommend the use of pre ssure washers or garden ho se to clean your un it. These may cause damag e to bearings or th ...
-
Troy-Bilt 430 Series - page 13
13 SECTION 7: SERVICING YOUR LAWN MOWER Blade Care Periodically inspect t he blade ada pter and pulley for cracks, especially if you strike a foreign object. Replace when neces sary. • Disconnect spark pl ug wire from spar k plug. • Turn mower on its side making sur e that the air filter and the carburet or are up. • Remove the bolt and bla d ...
-
Troy-Bilt 430 Series - page 14
14 Replacing Rear Flap • To remove rear flap , cut off the fl at end of the wire rod which secures it to the deck. See Figure 14 . • Attach the new f lap and new rod t o deck, bending the ends of the new rod over to secure to deck. Figure 14 SECTION 8: MAKING ADJUSTMENTS Adjusting Handle Height Your mower is shipped with t he handle in the high ...
-
Troy-Bilt 430 Series - page 15
15 SECTION 9: OFF-SEASON STORAGE Prepare your lawn mowe r for storage at the en d of the season or if the unit will not be used for 30 days or more. Store th e mower in a clean, dry area . Gasoline • Do not store gasoline from one season to another. Gasoline, stored more t han one month, may affe ct engine perfor mance. • Replace your gasoline ...
-
Troy-Bilt 430 Series - page 16
16 29 25 40 37 41 40 38 43 27 26 25 20 35 33 24 22 21 28 31 44 47 25 36 13 52 7 11 9 6 10 42 45 17 16 23 46 2 4 50 30 49 5 8 3 1 15 53 14 19 18 39 12 25 48 32 34 43 31 51 54 SECTION 11: PARTS LIST FOR MODEL SERIES 430 ...
-
Troy-Bilt 430 Series - page 17
17 Model Series 430 Ref. No. Part No. Description 1. 747-1161A Control Handle 2. 710-1205 Rope Guide 3. 720-0279 Handle Knob 1/4-20 Thd. 4. 710-1174 Curved Hd. Bolt 5/16-18 x 2" 5. 720-0284 Hand Knob 6. 749-1092A Upper Handle 7. 749-0928A Lower Handle 8. 726-0240 Cable Tie 9. 747-04080 Grass Catcher Frame 10. 746-1130 Control Cable - 40” 11. ...
-
Troy-Bilt 430 Series - page 18
18 NOTES ...
-
Troy-Bilt 430 Series - page 19
19 NOTES ...
-
Troy-Bilt 430 Series - page 20
MANUF A CTURER’S LIMITED W ARRANTY FOR: The limited warranty set forth be low is given by Troy-Bilt LLC with respect to new merchandise purchased and used in the United States, its possessions an d territories. “Troy-Bilt” warrants this produc t against defects in material and workmanship for a pe riod of two (2) years commencing on the date ...
Hai una domanda su Troy-Bilt 430 Series?
Utilizza il modulo sottostante
Se non hai risolto il problema con Troy-Bilt 430 Series con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Troy-Bilt 430 Series è probabile che voglia condividere il modo di risolverlo.