-
Geemarc AMPLIVOICE50 - page 1
...
-
Geemarc AMPLIVOICE50 - page 2
CONTENTS 2 INTRODUCTION Important safety instructions 3 Unpacking the AmpliVOICE50 3 DESCRIPTION General Description 4 LCD Screen Description 6 Menu Navigation 6 INST ALLA TION Setting Up 7 W all Mounting 9 SETTINGS Language Setting 10 Screen Contrast Setting 10 T ime Setting 1 1 V oice Function Setting 12 Flash (Recall) Setting 12 Dialling Mode (T ...
-
Geemarc AMPLIVOICE50 - page 3
3 INTRODUCTION IMPORT ANT SAFETY INSTRUCTIONS When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fi re, electric shock and injury to persons, including the following: 1. Do not use this product near water , for example, near a bath tub, wash bowl,kitchen sink or laundry tub, in a wet basem ...
-
Geemarc AMPLIVOICE50 - page 4
4 DESCRIPTION 12 3 4 5 6 8 9 10 11 12 13 14 15 16 17 18 7 General Description ...
-
Geemarc AMPLIVOICE50 - page 5
5 DESCRIPTION 1= Call back, con fi rm 2= Quick Dial M1 (emergency call number 1) 3= Delete 4= Quick Dial M2 (emergency call number 2) 5= Scroll upwards 6= Quick Dial M3 (emergency call number 3) 7= Scroll downwards 8= LED( fl ashes when a new call has been received) 9= Menu button 10= Phonebook, Exit, Caller ID 1 1= Recall 12= Mute 13= Redial, In ...
-
Geemarc AMPLIVOICE50 - page 6
6 DESCRIPTION LCD Screen Description This LCD display shows the total number of calls and the number of new calls ready to be reviewed. In this example you have a total of 4 calls which includes two new calls. Menu Navigation T o access settings, press MENU . T o exit the menu, press CID . T o skip back a level within the menu, press DELETE The tel ...
-
Geemarc AMPLIVOICE50 - page 7
7 Setting Up Connect the handset to one end of the curly cord. The connector at the end of the curly cord plugs into the socket on the left hand side of the AmpliVOICE50 unit. Open the battery compartment (push the small clip backwards and then upwards). Insert 4 good quality alkaline batteries (AA size, 1.5V type, not supplied) into the battery co ...
-
Geemarc AMPLIVOICE50 - page 8
8 Note: Mains power is required to power the multifunction features of the telephone. Fit 4 x AA sized batteries in order to save and use stored numbers in case of mains power failure. Without mains or battery power , the telephone can still be used to answer calls or to manually dial out calls but all the multifunction features will not be availab ...
-
Geemarc AMPLIVOICE50 - page 9
9 W all Mounting Feed the guide tabs (1) on the wall-mounting bracket (2) in the slots (3) on the underside of the telephone. Slide the wall-mounting bracket 10 mm upwards until it audibly locks into place. Drill a hole and insert a screw leav- ing about 5 mm of the screw projecting from the wall. Guide the mounting hole (4) in the mounting bracket ...
-
Geemarc AMPLIVOICE50 - page 10
10 Language Setting Y ou can choose between 4 different languages including English and French. Each language has voice announcements available in that language. Press MENU Use ▲ or ▼ to select LANGUAGE Press DIAL to select Use ▲ or ▼ to select the desired language Press DIAL to select Press CID to exit Screen Contrast Setting Y our screen ...
-
Geemarc AMPLIVOICE50 - page 11
11 T ime Setting If you subscribe to a Caller Display service, the date and time will be set whenever you receive a call. However , if you do not subscribe to this service, you will need to set the date and time manually . Press MENU Use ▲ or ▼ to select TIME/DA TE Press DIAL to select The HOUR digit will fl ash. Use ▲ or ▼ to select the c ...
-
Geemarc AMPLIVOICE50 - page 12
12 V oice Function Setting When the VOICE function is ON, in pre-dial mode numbers 0-9, numbers held in the call log, numbers held in the phone book and a caller ’ s name (if recorded, see Phonebook Chapter – Storing Name Recording) will be announced in the loudspeaker . Press MENU Use ▲ or ▼ to select VOICE Press DIAL to select Use ▲ or ...
-
Geemarc AMPLIVOICE50 - page 13
13 Press MENU Use ▲ or ▼ to select TONE/PULSE Press DIAL to select Use ▲ or ▼ to select the desired method, TONE or PULSE 40/60 Press DIAL to select Press CID to exit Ringer V olume Setting A switch located on the right side of the AmpliVOICE50 unit allows the ringer to be switched to LOW , MEDIUM or HIGH. Making a Call Pick up the handset. ...
-
Geemarc AMPLIVOICE50 - page 14
14 USING THE TELEPHONE Making a Call – Hands Free Dial the number on the keypad in the on-hook position Use DELETE if necessary to cancel and correct a wrong digit Press and the number will be dialled automatically . The handsfree function (speaker) is now activated and the LED indicator next to the button will be illuminated. When the third part ...
-
Geemarc AMPLIVOICE50 - page 15
15 USING THE TELEPHONE Receiving a Call When an incoming call is received, the telephone rings and the LCD display backlight lights up. If the caller can be identi fi ed (due to subscription to a Caller Display service), the caller ’ s telephone number will be displayed. The caller ’ s name will also be displayed provided that the number and n ...
-
Geemarc AMPLIVOICE50 - page 16
16 Mute Function If you wish, you can speak privately to someone else in the room without your caller overhearing. Y ou will still be able to hear the caller but they cannot hear you during the mute operation. T o switch on the mute mode during a call just press and hold MUTE button. Y our caller will not be able to hear you anymore. Release MUTE t ...
-
Geemarc AMPLIVOICE50 - page 17
17 Call T imer Y our handset automatically times the duration of every external call. The time is shown during the call and for a few seconds after the call has ended. Hearing Aid Use This telephone is hearing aid compatible. Select the T mode on your hear- ing aid to enable this feature. USING THE TELEPHONE ...
-
Geemarc AMPLIVOICE50 - page 18
18 The features described in this section are only available if you subscribe to a Caller Display service from your network provider . Caller Display means you can see who is calling before you answer a call or see who has called in your absence (provided the number is not with- held, unavailable or is an international call). If the number is store ...
-
Geemarc AMPLIVOICE50 - page 19
19 Y our telephone displays incoming call waiting Caller ID information while you are on another call. Once you have received a Call W aiting call, the CALL W AITING icon will light. Note: The Call W aiting information will be disappear after 20 seconds. V iew Caller Display List Use ▲ or ▼ to scroll through the caller display list Notes: At th ...
-
Geemarc AMPLIVOICE50 - page 20
20 CALLER DISPLA Y Delete an Entry from the Caller Display List Use ▲ and ▼ to scroll through the caller display list until you fi nd the telephone number you wish to delete Press DELETE, DELETE? will be shown on the LCD display Press and hold DELETE until the telephone number disappears Press CID to exit Delete All Entries from the Caller Dis ...
-
Geemarc AMPLIVOICE50 - page 21
21 T elephone numbers and associated names can be stored in the phone book. The phone book can contain 30 telephone numbers (maximum of 22 digits) with names (maximum of 16 letters). If you subscribe to a caller ID service the name in the phone book will be shown for incoming calls. Create a Phone Book Entry Press MENU Use ▲ or ▼ to select STOR ...
-
Geemarc AMPLIVOICE50 - page 22
22 PHONE BOOK Some telephone systems require a pause to be inserted when dialling a number . T o insert a dialling pause (of 3 seconds) between digits when storing a telephone number , press REDIAL until P appears in the LCD display . Store/Change a Name Recording Press MENU Use ▲ or ▼ to select NAME RECORDING Press DIAL to select Use ▲ or ? ...
-
Geemarc AMPLIVOICE50 - page 23
23 Delete a Name Recording Press MENU Use ▲ or ▼ to select NAME RECORDING Press DIAL to select Use ▲ or ▼ to select the desired telephone number to be deleted Press DELETE while the recording is played back Press CID when you are ready to exit V iew Phone Book Entries Press CID Use ▲ and ▼ to scroll through the phone book entries. If na ...
-
Geemarc AMPLIVOICE50 - page 24
24 PHONE BOOK Modify a Phone Book Entry Locate the required telephone number as shown in one of the above methods (see View Phone Book Entries) Press and hold MENU until the LCD display shows EDIT?. Press DIAL Press DELETE to modify the name and insert the new numbers. Use ▲ or ▼ to move to the required number Press DIAL Press DELETE to modify ...
-
Geemarc AMPLIVOICE50 - page 25
25 Delete all Phone Book Entries Locate any telephone number as shown in one of the above methods (see View Phone Book Entries) Press and hold DELETE, DELETE ALL? will be shown on the LCD display Press and hold DELETE until EMPTY shows Press CID to exit PHONE BOOK ...
-
Geemarc AMPLIVOICE50 - page 26
26 QUICK DIAL M1, M2 and M3 can also be used as quick dial locations Storing a Quick Dial Number Press MENU Use ▲ or ▼ to select STORE NUMBER Press DIAL Enter the telephone number to be stored (maximum of 22 digits) Press DIAL Select the speed dial location (M1, M2 or M3 ) by pressing the corresponding button Dialling a Quick Dial Number Press ...
-
Geemarc AMPLIVOICE50 - page 27
27 No display • Make sure that the power adaptor is plugged in correctly and is not damaged AmpliVOICE50 does not ring • Make sure that the telephone line cord is plugged in correctly and is not damaged • Connect another telephone to the telephone PTT socket or move your telephone to another socket to track if the failure is coming from your ...
-
Geemarc AMPLIVOICE50 - page 28
28 General Only use the power supply included with the product. Do not open the unit (except to replace the batteries). Contact the helpline for all repairs. Never dispose of batteries in a fi re. There is a serious risk of explosion and/ or the release of toxic chemicals. Cleaning Clean the telephone with a soft cloth. Keep the base and handset c ...
-
Geemarc AMPLIVOICE50 - page 29
29 - This equipment complies with Part 68 of the FCC rules and the require- ments adopted by the ACT A. On the bottom of this equipment is a label that contains, among other information, a product identi fi er in the format US:AAAEQ##TXXXX. If requested, this number must be provided to the telephone company . - All applicable certi fi cation jack ...
-
Geemarc AMPLIVOICE50 - page 30
30 NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. Some cordless telephones operate at frequencies that may cause interference to nearby ...
-
Geemarc AMPLIVOICE50 - page 31
31 GUARANTEE Sonic Alert warrants the phone against any defect in materials or workman- ship for the period of one year from the date of purchase. Should you experience a problem, contact our customer service department. Be sure to save your sales receipt as proof of purchase date should you need warranty service. Within a period of one year from p ...
Hai una domanda su Geemarc AMPLIVOICE50?
Utilizza il modulo sottostante
Se non hai risolto il problema con Geemarc AMPLIVOICE50 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Geemarc AMPLIVOICE50 è probabile che voglia condividere il modo di risolverlo.