Italiano dropdown-ico

Manuale per l’uso Genie 114002

36 pagine 1.23 mb
Scarica

Vai alla pagina of 36

Summary
  • Genie 114002 - page 1

    Operator’ s Manual with Maintenance Information Third Edition First Printing Part No. 114002 ...

  • Genie 114002 - page 2

    Operator’s Manual Third Edition • First Printing 2 Genie A WP Super Series Part No. 1 14002 Copyright © 1996 by Genie Industries First Edition: Eighth Printing, October 2001 Second Edition: Second Printing, April 2004 Third Edition: First Printing, August 2005 "Genie" and "AWP" are registered trademarks of Genie Industries ...

  • Genie 114002 - page 3

    Operator’s Manual Third Edition • First Printing Part No. 1 14002 Genie AWP Super Series 1 Safety Rules Danger Failure to obey the instructions and safety rules in this manual will cause death or serious injury . Do Not Operate Unless: You learn and practice the principles of safe machine operation contained in this operator's manual. 1 Av ...

  • Genie 114002 - page 4

    Operator’s Manual Third Edition • First Printing 2 Genie AWP Super Series Part No. 1 14002 SAFETY RULES Electrocution Hazards This machine, even with an optional fiberglass platform, is not electrically insulated and will not provide protection from contact with or proximity to electrical current. Keep away from the machine if it contacts energ ...

  • Genie 114002 - page 5

    Operator’s Manual Third Edition • First Printing Part No. 1 14002 Genie AWP Super Series 3 SAFETY RULES Do not raise the platform unless the machine is level. Do not set the machine up on a surface where it cannot be leveled using only the leveling jacks. Do not cause a horizontal force or side load to the machine by raising or lowering a fixed ...

  • Genie 114002 - page 6

    Operator’s Manual Third Edition • First Printing 4 Genie AWP Super Series Part No. 1 14002 SAFETY RULES Fall Hazards The guard rail system provides fall protection. If occupants of the platform are required to wear personal fall protection equipment (PFPE) due to job site or employer rules, PFPE equipment and its use shall be in accordance with ...

  • Genie 114002 - page 7

    Operator’s Manual Third Edition • First Printing Part No. 1 14002 Genie AWP Super Series 5 SAFETY RULES Improper Use Hazard Do not leave the machine unattended unless the key is removed to secure from unauthorized use. Bodily Injury Hazard Do not operate the machine with a hydraulic oil or air leak. An air leak or hydraulic leak can penetrate a ...

  • Genie 114002 - page 8

    Operator’s Manual Third Edition • First Printing 6 Genie AWP Super Series Part No. 1 14002 Battery and Charger Safety - DC Models Burn Hazards Batteries contain acid. Always wear protective clothing and eye wear when working with batteries. Avoid spilling or contacting battery acid. Neutralize battery acid spills with baking soda and water. The ...

  • Genie 114002 - page 9

    Operator’s Manual Third Edition • First Printing Part No. 1 14002 Genie AWP Super Series 7 SAFETY RULES Decal Legend Genie product decals use symbols, color coding and signal words to identify the following: Safety alert symbol—used to alert personnel to potential personal injury hazards. Obey all safety messages that follow this symbol to av ...

  • Genie 114002 - page 10

    Operator’s Manual Third Edition • First Printing 8 Genie AWP Super Series Part No. 1 14002 Controls 1 Red Emergency Stop button 2 Key switch 3 Outrigger interlock display lights (four) 4 Low battery indicator light for auxiliary lowering 5 DC models: Low battery indicator light 6 Power light 7 Auxiliary platform lowering button 8 Air pressure g ...

  • Genie 114002 - page 11

    Operator’s Manual Third Edition • First Printing Part No. 1 14002 Genie AWP Super Series 9 Legend 9 Loading pivot bar 1 0 Forklift pocket 1 1 Airline lubricator adjustment knob 1 2 Air supply for machine 1 3 Airline lubricator 1 4 DC models: Battery pack with charger 1 5 Hydraulic power unit 1 6 Winching/tie-down point 1 7 Bubble level 1 8 Base ...

  • Genie 114002 - page 12

    Operator’s Manual Third Edition • First Printing 10 Genie AWP Super Series Part No. 1 14002 Pre-operation Inspection Do Not Operate Unless: You learn and practice the principles of safe machine operation contained in this operator’s manual. 1 Avoid hazardous situations. 2 Always perform a pre-operation inspection. Know and understand the pre- ...

  • Genie 114002 - page 13

    Operator’s Manual Third Edition • First Printing Part No. 1 14002 Genie AWP Super Series 11 PRE-OPERATION INSPECTION Pre-operation Inspection o Be sure that the operator’s, safety and responsibilities manuals are complete, legible and in the storage container located on the platform. o Be sure that all decals are legible and in place. See Dec ...

  • Genie 114002 - page 14

    Operator’s Manual Third Edition • First Printing 12 Genie AWP Super Series Part No. 1 14002 Maintenance Observe and Obey: Only routine maintenance items specified in this manual shall be performed by the operator. Scheduled maintenance inspections shall be completed by qualified service technicians, according to the manufacturer's specific ...

  • Genie 114002 - page 15

    Operator’s Manual Third Edition • First Printing Part No. 1 14002 Genie AWP Super Series 13 MAINTENANCE Check the Hydraulic Oil Level Maintaining the hydraulic oil at the proper level is essential to machine operation. Improper hydraulic oil levels can damage hydraulic components. Daily checks allow the inspector to identify changes in oil leve ...

  • Genie 114002 - page 16

    Operator’s Manual Third Edition • First Printing 14 Genie AWP Super Series Part No. 1 14002 MAINTENANCE Check the Oil Lubricator Canister Drip Rate - Air Models Maintaining the proper oil drip rate into the lubricator canister is essential to safe operation and good machine performance. Failure to maintain the proper drip rate could result in m ...

  • Genie 114002 - page 17

    Operator’s Manual Third Edition • First Printing Part No. 1 14002 Genie AWP Super Series 15 Function T ests Do Not Operate Unless: You learn and practice the principles of safe machine operation contained in this operator’s manual. 1 Avoid hazardous situations. 2 Always perform a pre-operation inspection. 3 Always perform the function tests p ...

  • Genie 114002 - page 18

    Operator’s Manual Third Edition • First Printing 16 Genie AWP Super Series Part No. 1 14002 FUNCTION TESTS Function T ests Setup 1 Position the machine on a firm surface directly below the desired work area. 2 Connect to the appropriate power source: DC models: Connect the battery pack. AC models: Connect to a grounded 15A AC power supply. Use ...

  • Genie 114002 - page 19

    Operator’s Manual Third Edition • First Printing Part No. 1 14002 Genie AWP Super Series 17 1 2 Push in the red Emergency Stop button at the platform controls to the off position. 1 3 Pull out the red Emergency Stop button at the ground controls to the on position. 1 4 Push in the control activate button and rotate the up/down switch in the dir ...

  • Genie 114002 - page 20

    Operator’s Manual Third Edition • First Printing 18 Genie AWP Super Series Part No. 1 14002 W orkplace Inspection Do Not Operate Unless: You learn and practice the principles of safe machine operation contained in this operator’s manual. 1 Avoid hazardous situations. 2 Always perform a pre-operation inspection. 3 Always perform function tests ...

  • Genie 114002 - page 21

    Operator’s Manual Third Edition • First Printing Part No. 1 14002 Genie AWP Super Series 19 Do Not Operate Unless: You learn and practice the principles of safe machine operation contained in this operator’s manual. 1 Avoid hazardous situations. 2 Always perform a pre-operation inspection. 3 Always perform function tests prior to use. 4 Inspe ...

  • Genie 114002 - page 22

    Operator’s Manual Third Edition • First Printing 20 Genie AWP Super Series Part No. 1 14002 OPERATING INSTRUCTIONS Emergency Stop Push in the red Emergency Stop button at the platform controls or at the ground controls to stop the up function. Platform Raise and Lower 1 Pull out the red Emergency Stop button to the on position at the ground con ...

  • Genie 114002 - page 23

    Operator’s Manual Third Edition • First Printing Part No. 1 14002 Genie AWP Super Series 21 Battery and Charger Instructions Observe and Obey: Do not use an external charger or booster battery. Charge the battery in a well-ventilated area. Use proper AC input voltage for charging as indicated on the charger. Use only Genie authorized battery an ...

  • Genie 114002 - page 24

    Operator’s Manual Third Edition • First Printing 22 Genie AWP Super Series Part No. 1 14002 Lifting Instructions The number of people required to load and unload a machine is dependent on a number of factors, including but not limited to: · the physical condition, strength and disabilities or prior injuries of the people involved · the vertic ...

  • Genie 114002 - page 25

    Operator’s Manual Third Edition • First Printing Part No. 1 14002 Genie AWP Super Series 23 Loading for T ransport 1 Fully lower the platform. 2 Push in the red Emergency Stop buttons, turn the key switch to the off position and remove the key. 3 Remove the outriggers from the base and place them in the storage sockets. 4 DC models: Disconnect ...

  • Genie 114002 - page 26

    Operator’s Manual Third Edition • First Printing 24 Genie AWP Super Series Part No. 1 14002 TRANSPORT INSTRUCTIONS Winching the Machine onto a Flatbed T ruck 1 Fully lower the platform. 2 Push in the red Emergency Stop buttons, turn the key switch to the off position and remove the key. 3 Remove the outriggers from the base and place them in th ...

  • Genie 114002 - page 27

    Operator’s Manual Third Edition • First Printing Part No. 1 14002 Genie AWP Super Series 25 Tilt-back Operation Instructions Observe and obey: The retaining pin must be inserted to prevent the spring-loaded tilt-back frame from dropping. Do not tilt the machine back unless the area is clear of personnel and obstructions. Do not stand behind or ...

  • Genie 114002 - page 28

    Operator’s Manual Third Edition • First Printing 26 Genie AWP Super Series Part No. 1 14002 TILTBACK OPERATION INSTRUCTIONS Lowering the Tilt-back Assembly 1 Be sure the area behind the machine and under the tilt-back frame is clear of personnel and obstructions. 2 Fully lower the platform. 3 Remove the outriggers from the base and place them i ...

  • Genie 114002 - page 29

    Operator’s Manual Third Edition • First Printing Part No. 1 14002 Genie AWP Super Series 27 Returning the Machine to Standing Position 1 Be sure the area below the machine base and T-handle is clear of personnel and obstructions. 2 Slide out the T-handle untl the lock pin snaps into place. 3 Carefully pull down the T-handle until the machine re ...

  • Genie 114002 - page 30

    Operator’s Manual Third Edition • First Printing 28 Genie AWP Super Series Part No. 1 14002 Decals Part No. Description Quantity 27838 Warning - Tilt-back Hazards/Instructions 1 27839 L ab el - Sl id i ng T- handle 1 27840 Label - Retaining Pin 1 27841 Label - Stop Bracket 1 27842 Label - Loading Pivot 1 27843 Label - Tilt-back Strut 1 27844 La ...

  • Genie 114002 - page 31

    Operator’s Manual Third Edition • First Printing Part No. 1 14002 Genie AWP Super Series 29 DECALS Models with T ilt-back Frame Note: Platform decals may be in diffferent locations on optional fiberglass basket. Models without T ilt-back Frame ...

  • Genie 114002 - page 32

    Operator’s Manual Third Edition • First Printing 30 Genie AWP Super Series Part No. 1 14002 DECALS Inspection for Decals with Symbols Determine whether the decals on your machine have words or symbols. Use the appropriate inspection to verify that all decals are legible and in place. Part No. Description Quantity 28174 Label - Power to Platform ...

  • Genie 114002 - page 33

    Operator’s Manual Third Edition • First Printing Part No. 1 14002 Genie AWP Super Series 31 Note: Platform decals may be in diffferent locations on optional fiberglass basket. DECALS Models with T ilt-back Frame Models without T ilt-back Frame ...

  • Genie 114002 - page 34

    Operator’s Manual Third Edition • First Printing 32 Genie AWP Super Series Part No. 1 14002 Outrigger Specifications Standard Base AWP-20S AWP-25S AWP-30S Outrigger footprint 60 3 / 4 x 52 3 / 4 in 60 3 / 4 x 52 3 / 4 in 69 1 / 4 x 61 1 / 4 in (l x w) ANSI / CSA 1.5 x 1.3 m 1.5 x 1.3 m 1.8 x 1.6 m Outrigger footprint 60 3 / 4 x 52 3 / 4 in 69 1 ...

  • Genie 114002 - page 35

    Operator’s Manual Third Edition • First Printing Part No. 1 14002 Genie AWP Super Series 33 SPECIFICATIONS Outrigger Specifications Standard Base AWP-36S AWP-40S Outrigger footprint 83 1 / 4 x 75 1 / 4 in 89 x 81 in (l x w) ANSI / CSA 2.1 x 1.9 m 2.3 x 2.0 m Outrigger footprint 83 1 / 4 x 75 1 / 4 in 89 x 81 in (l x w) CE / AUS Indoor 2.1 x 1.9 ...

  • Genie 114002 - page 36

    Geni e Nort h America Geni e Australi a Pt y Ltd. Geni e China Geni e Malaysia Geni e Japan Geni e Korea Geni e Brasil Geni e Holland Phone Tol l Free Fax Phon e+ Fa x+ Phon e+ Fa x+ Phon e+ Fa x+ Phon e+ Fa x+ Phon e+ Fa x+ Phon e+ Fa x+ Phon e+ Fa x+ 425.881.1800 US A an d Canada 800.536.1800 425.883.3475 6 17 337 5 1660 6 17 337 5 1002 8 6 2 1 5 ...

Fabbricante Genie Categoria Utility Vehicle

I documenti che otteniamo dal fabbricante del dispositivoGenie 114002 possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Genie
- manuali per l’uso 114002
- schede prodotto Genie
- opuscoli
- o etichette energetiche Genie 114002
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Genie 114002.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Genie 114002, manuali di manutenzione, brevi manuali o manuali utente Genie 114002. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Genie 114002.

Manuali per l’uso simili

Manuale completo del dispositivo Genie 114002, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Genie 114002 dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Genie 114002.

Il manuale per l’uso completo Genie, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Genie 114002 - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Genie 114002, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Genie 114002 che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Genie 114002 - che ci dovrebbe aiutare nei primi passi durante l'uso Genie 114002
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Genie 114002
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Genie 114002 in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Genie 114002?

Utilizza il modulo sottostante

Se non hai risolto il problema con Genie 114002 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Genie 114002 è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)