Italiano dropdown-ico

Manuale per l’uso Audiovox APS-687a

24 pagine 0.66 mb
Scarica

Vai alla pagina of 24

Summary
  • Audiovox APS-687a - page 1

    128-8121 1 of 24 1 The selectable features can be set manually as explained below , or with the RF feature programmer . T o set features using the RF programmer , follow the instructions packaged with the programmer . Factory default settings are indicated by bold text. Note : The method of manual override can either be selected to operate from the ...

  • Audiovox APS-687a - page 2

    128-8121 2 of 24 2 T o program these selectable features; Action System Response Turn ignition on No response Press and release the valet switch 3 times 1 Chirp - LED 1 flash Within 3 seconds, turn ignition Off Then On Short chirp, then long chirp This Action Accesses Feature Bank 2 Alarm Selectable Features First Press and release the valet switch ...

  • Audiovox APS-687a - page 3

    128-8121 3 of 24 3 T o exit program mode, turn ignition off, or press and release valet switch. RF Programmable Features Bank 3 Is Remote Start Selectable Features: Feature Selection 1 Chirp 2 Chirps 3 Chirps 4 Chirps 5 Chirps 6 Chirps 1st Defrost Output Pulsed 10 Mins 2nd RF S tart Chirp O f f On On & Car Finder 3rd Run Time 5 Mins 10 Mins 15 ...

  • Audiovox APS-687a - page 4

    128-8121 4 of 24 4 Action System Response Turn ignition on No response Press and release the valet switch 3 times 1 Chirp - LED 1 flash Within 3 seconds, turn ignition Off, On, Off, On Short chirp, then 2 long chirps This Action Accesses Feature Bank 3 Remote S tart Selectable Features First Press the valet switch one time 1 chirp = defrost output ...

  • Audiovox APS-687a - page 5

    128-8121 5 of 24 5 This system is to be used in vehicles with AUTOMA TIC TRANSMISSIONS only! Although this combina- tion Keyless Entry/Remote S tart unit is a sophisticated system with many advanced features, IT MUST NOT be installed into a vehicle with a manually operated transmission. Doing so may result in serious personal injury and property da ...

  • Audiovox APS-687a - page 6

    128-8121 6 of 24 6 This Remote S tart System is designed for use with Automatic T ransmission V ehicles Only! The unit provides wait to start input for glow plug pre-heat which will be used for all diesel applications. If this wire is not connected, then the unit will remain in the Gasoline mode setting, which will crank the car when the RF signal ...

  • Audiovox APS-687a - page 7

    128-8121 7 of 24 7 Note: This wire must be connected to the vehicle side of the starter cut relay (when used). For the electrical neutral switch configuration, this connection must be made between the starter inhibit relay , (when used) and the neutral safety switch as shown in the following diagram. Failure to connect this wire to the ignition swi ...

  • Audiovox APS-687a - page 8

    128-8121 8 of 24 8 WIRING THE 4 PIN AL TERNA TE IGNITION HARNESS ORANGE/BLACK Wire: Parking Brake Input This wire is used only when the turbo timer mode, Bank 3, feature # 16 is selected ON. This input insures that the vehicle parking brake is applied whenever the vehicle is set up for and the turbo timer circuit is used. This input must switch to ...

  • Audiovox APS-687a - page 9

    128-8121 9 of 24 9 WIRING CONNECTIONS: 12 Pin Input / Output Harness Black Wire: Chassis Ground Source Connect the Black wire to a known vehicle ground source or to a solid clean metal part of the chassis. Be certain to remove any paint or grease and secure this wire with a self- tapping screw and ring terminal. GRAY WIRE: Negative Inhibit Input 1 ...

  • Audiovox APS-687a - page 10

    128-8121 10 of 24 10 YELLOW w/ BLACK Tracer Wire: + 12 Volt Alarm By - Pass Output Note: You must disconnect the ignition input of the alarm from any other wire that it is presently connected to in the vehicle. This wire provides a + 12 Volt output when the ignition key is turned to the “ON” position, and 0 Volts when the ignition key is “OFF ...

  • Audiovox APS-687a - page 11

    128-8121 11 of 24 11 C. GM V A TS Key Override: If the vehicle has the General Motors V A TS system installed, you will need to bypass the system while the vehicle is operating under the control of the Remote S tart Unit. T o Do This; 1. Measure the resistance of the resistor pellet on the ignition key then select a resistor within 5% of the key&ap ...

  • Audiovox APS-687a - page 12

    128-8121 12 of 24 12 Green/Y ellow Wire: Diesel W ait T o S tart Input The Green/Yellow wire will connect to a diesel vehicles glow plug wire. When the unit receives a start command, this wire must go to + 12 then to ground to allow the crank sequence to begin. When ignition #1 is activated by the remote start unit, the glow plug circuit gets energ ...

  • Audiovox APS-687a - page 13

    128-8121 13 of 24 13 3 Pin Door Lock/Unlock Harness: (White Connector) The Red and Green wires will provide either a pulsed ground output to the factory door lock control relay , or a pulsed + 12 volt output to the factory door lock control relay . In either case, the maximum current draw through these outputs must not exceed 300mA. The Red w/Black ...

  • Audiovox APS-687a - page 14

    128-8121 14 of 24 14 Most vehicles door lock/unlock motor legs rest at ground, and switch +12 volts to the door lock/unlock motor legs for operation, if this is the case in the vehicle you are working on, connect the remaining terminal, 87, to a fused + 12 volt source. In the rare instance that the vehicle door lock/unlock motor legs rest at + 12 v ...

  • Audiovox APS-687a - page 15

    128-8121 15 of 24 15 5 Pin Accessory Output Harness Dark Blue Wire : Delayed 300 mA Pulsed Output/Channel 3 The dark blue wire pulses to ground via an independent RF channel from the keychain transmitter. This is a transistorized, low current output, and should only be used to drive an external relay coil. This output is activated by the same trans ...

  • Audiovox APS-687a - page 16

    128-8121 16 of 24 16 wire the remaining relay contacts to perform the selected function of channel 6. Blue/Red Wire : DELA YED 300 mA PULSED OUTPUT / CHANNEL 7 The light blue/red wire pulses to ground via an independent RF channel from the keychain transmitter . This is a transistorized, low current output, and should only be used to drive an exter ...

  • Audiovox APS-687a - page 17

    128-8121 17 of 24 17 TIMED START OPERATION: To begin the start timer, within 10 seconds of turning off the ignition switch, activate the RF command to start 2 times. (Press the trunk/key button four times). The lights will flash and the siren will chirp 4 times. Indicating timed interval mode has been initiated. The vehicle will automatically start ...

  • Audiovox APS-687a - page 18

    128-8121 18 of 24 18 TESTING YOUR INST ALLA TION: W ARNING!! The following procedure must be performed after the installation of an Audiovox Remote S t art Device. It is the responsibility of the installing technician to complete these tests. Failure to test the unit in the following manner may result in personal injury , property damage, or both. ...

  • Audiovox APS-687a - page 19

    128-8121 19 of 24 19 8. Repeat the above test this time move the gear selector to the drive position. If the unit attempts to start, failing this test, recheck your Y ellow Wire's connection. This wire must be connected to the ignition switch side of the Neutral S tart Switch. If the vehicle you are working on does not have an Electrical Neutr ...

  • Audiovox APS-687a - page 20

    128-8121 20 of 24 20 Note: When completing an installation using either of the following key in sensor circuits, if the operator inserts the ignition key while the vehicle is running under the control of the Remote S tart, the vehicle will shut down. This must be explained to the operator as it is in contrast to the normal operation of a vehicle ut ...

  • Audiovox APS-687a - page 21

    128-8121 21 of 24 21 C. Locate the key in sensor switch wire that connects the chime module to the ignition cylinder . D. Cut this wire and connect the ignition cylinder side to the Remote S tart Negative Safety Shut down Wire Gray/Black, using a 4002 series diode as shown above. Note: A second 4002 series diode may be required to maintain the inte ...

  • Audiovox APS-687a - page 22

    128-8121 22 of 24 22 ...

  • Audiovox APS-687a - page 23

    128-8121 23 of 24 23 THIS PAGE LEFT BLANK INTENTIONALLY ...

  • Audiovox APS-687a - page 24

    128-8121 24 of 24 24 © 2007 Audiovox Electronics Corp., Hauppauge, NY 1 1788 128-8121 ...

Fabbricante Audiovox Categoria Remote Starter

I documenti che otteniamo dal fabbricante del dispositivoAudiovox APS-687a possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Audiovox
- manuali per l’uso APS-687a
- schede prodotto Audiovox
- opuscoli
- o etichette energetiche Audiovox APS-687a
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Audiovox APS-687a.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Audiovox APS-687a, manuali di manutenzione, brevi manuali o manuali utente Audiovox APS-687a. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Audiovox APS-687a.

Manuali per l’uso simili

Manuale completo del dispositivo Audiovox APS-687a, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Audiovox APS-687a dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Audiovox APS-687a.

Il manuale per l’uso completo Audiovox, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Audiovox APS-687a - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Audiovox APS-687a, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Audiovox APS-687a che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Audiovox APS-687a - che ci dovrebbe aiutare nei primi passi durante l'uso Audiovox APS-687a
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Audiovox APS-687a
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Audiovox APS-687a in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Audiovox APS-687a?

Utilizza il modulo sottostante

Se non hai risolto il problema con Audiovox APS-687a con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Audiovox APS-687a è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)