-
Hitachi CS 51EA - page 1
Chain Saw Model CS 51EA Handling instructions Note: Before using this machine, carefully read through these HANDLING INSTRUCTIONS to ensure e ffi cient, safe operation. It is recommended that these INSTRUCTIONS be kept readily available as an important reference when using this machine. 000Book_CS51EA_Eng.indb 1 000Book_CS51EA_Eng.indb 1 2011/09/04 ...
-
Hitachi CS 51EA - page 2
2 English MEANINGS OF SYM BO L S NOTE: Some units do not carry them. Symbols W ARNING The followin g show symbols used for the ma chine. Be sure tha t you understand their meaning bef ore use . It is important that you read, fully understand and observe the following safety precautions and warni ngs . Careless or improper use of the unit ma y cause ...
-
Hitachi CS 51EA - page 3
3 English WHA T IS WHA T? 1. Throt tle lev er: Device act ivated by the operator ʼ s fi nger , for controlling the engine speed. 2. Throttle le ver lockout: Device that pre vents the accidental operation of the throttle lever until manually released. 3. Stop sw itch: Device for allowing the engine to be started or stopped. 4. Oil tank cap : For c ...
-
Hitachi CS 51EA - page 4
4 English ○ Make sure the automatic oiler is wo rki ng. Kee p the oil tank fi lled with clean oil. Never let chain run dry on the bar . ○ All chain saw service, other than the items list ed in the operator ʼ s/ owner ʼ s manual, should be per formed by compet ent chain-saw ser vice personnel. (Fo r example, if improper tool s are used to rem ...
-
Hitachi CS 51EA - page 5
5 English SPECIF ICA TIONS ○ Code “CS” of model name means “Cha in sa w ” Model CS5 1EA (40 S) C S 51 E A (4 5 S) C S 51EA (50 S) Ty p e of equipment Chain saw , portable Engine Size (cm 3 ) 50. 1 Spark Plug NGK BP MR- 7A Fue l Ta n k Capacit y (c m 3 )5 3 0 Chain Oil Ta n k Capac ity (c m 3 )2 7 0 Dry Weight (kg) (Witho ut guide bar and ...
-
Hitachi CS 51EA - page 6
6 English CAUTI ON PROPER TENSION IS EX TREMEL Y IMPORT ANT 8. Raise the bar end and securely tighten the guide bar clamp nuts with the combi box spanner . ( Fig. 7 ) 9. A new chain will stretch so adjust the chain after a few cuts and watch chain tension carefully for the fi rst half hour of cutting. NOTE Check the chain tensi on frequently for o ...
-
Hitachi CS 51EA - page 7
7 English 15 16 Fig. 9 Chain oil (Fig . 9) Fill up with chain oil (16). Always use good quality chain oil. When the engine is running, the chain oil is automatically discharged. NOTE When pouring fuel (15 ) or chain oil (16) into the tank, place the unit with cap side up. ( Fig . 9 ) ADJUSTMENT OF CHAIN OIL S UPPL Y The chain oil quantity discharge ...
-
Hitachi CS 51EA - page 8
8 English 4. Pull recoil starter briskly , taking care to keep the handle in yo ur grasp and not allowing it to snap back. ( Fig. 15 ) Fig. 15 5. When you hear fi rst ignition, return the chok e lever (19) all the way in. ( Fig. 13 ) 6. Push the decompression valve. 7. Pull recoil star ter briskly again in the aforementioned manner . ( Fig. 15 ) N ...
-
Hitachi CS 51EA - page 9
9 English ○ In case the chain locked, immediately release the thro ttle lever . If the throt tle lever ke ep s rotating at high speed with the chain locked, the clutch will ove rh eat causing trouble . NOTE Always ke ep the spiked bumper face to a tree, beca use the chain may suddenly be drawn into a tree. FELLING Felling is more than cutting dow ...
-
Hitachi CS 51EA - page 10
10 English CROSS CUTTING LOGS, PRESSU RE ON TOP Ta k e a fi rm stance. Begin with an upper cut. Do not cut too deeply , about 1/3 of the log diameter is enough. Finish with a bottom cut. The saw cuts should meet. ( Fig. 24 ) 30 28 31 32 29 33 Fig. 24 28. Relieving cut 29. Cross cut 30. Pre ssure on top 31. Pressure side 32. Te n s i o n side 33. R ...
-
Hitachi CS 51EA - page 11
11 English Id le s p ee d a dj us tm e nt ( T ) Ch ec k th at t he a i r fi lte r is clean . Wh en th e idl e spe ed i s c orrect , th e cu t ti ng a t t ac hm en t wi ll n ot r ot at e. If a dj us t me nt i s re qu ir ed , cl o se (clo c k wi se) th e T-sc re w, wit h th e e ng in e r un ni ng , un ti l th e c ut t in g attachment starts to rotat ...
-
Hitachi CS 51EA - page 12
12 English Chain oil fi lter (Fig. 37) Remove the oil fi lter and thoroughly wash it in solvent. Fig. 37 Cleaning the cylinder fi ns (Fig . 38) When wood chips are caught between cylinder fi ns (4 4), the engine may overheat, resulting in lower output. To avoi d this, alw ays keep cylinder fi ns and fan case clean. 44 Fig. 38 Icing protection ...
-
Hitachi CS 51EA - page 13
13 English Fig. 43 4) Round o ff front corner to maintain original shape of depth ga uge after using depth gauge too l. Alway s follow the recommended depth gauge set ting found in the maintenance or operator manual for your saw . ( Fig. 44 ) Fig. 44 GENERAL INSTRUCTIONS FOR FILING CUT TERS File (60) cutter on one side of the chain from the inside ...
-
Hitachi CS 51EA - page 14
14 000Book_CS51EA_Eng.indb 14 000Book_CS51EA_Eng.indb 14 2011/09/04 16:26:50 2011/09/04 16:26:50 ...
-
Hitachi CS 51EA - page 15
15 ITEM NO. PART NAME Q’TY 1 START LABEL 1 2 CLEANER COVER (C51) 1 3 SHUTTER PLATE 1 4 COVER SET BOLT 7 5 CYLINDER COVER (C51) 1 6 CLEANER KNOB 1 7 KNOB PACKING 1 8 CLEANER ELEMENT (B) 1 9 CLEANER ELEMENT (A) 1 10 NUT M6 3 11 BOLT WASHER M6 1 12 SPRING HOLDER 1 13 HEX. SOCKET HD. BOLT (W/FLANGE) M6 × 20 1 14 ANTIVIBRATION SPRING 1 15 DAMPER SET ...
-
Hitachi CS 51EA - page 16
Shinagawa Intercity Tower A, 15-1, Konan 2-chome, Minato-ku, Tokyo, Japan 109 Code No. E99245511 G Printed in China 000Book_CS51EA_Eng.indb 16 000Book_CS51EA_Eng.indb 16 2011/09/04 16:26:53 2011/09/04 16:26:53 ...
Hai una domanda su Hitachi CS 51EA?
Utilizza il modulo sottostante
Se non hai risolto il problema con Hitachi CS 51EA con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Hitachi CS 51EA è probabile che voglia condividere il modo di risolverlo.