Italiano dropdown-ico

Manuale per l’uso HP (Hewlett-Packard) C100

34 pagine 0.57 mb
Scarica

Vai alla pagina of 34

Summary
  • HP (Hewlett-Packard) C100 - page 1

    C100_110-160_180.FB -1 Tue Jul 16 06:36:50 1996 Installing the C100/C1 10 to C160/C180 CPU Upgrade HP Part No. A4200-90017 E0796 Printed in USA ...

  • HP (Hewlett-Packard) C100 - page 2

    C100_110-160_180.FB 0 Tue Jul 16 06:36:50 1996  Hewlett-Packard Co. 1996 Printing History First Printing: July 1996 UNIX is a registered trademark in the United States and other countries, licensed exclusively through X/Open Company Limited. NOTICE The information contained in this document is subject to change without notice. HEWLETT -P ACKARD ...

  • HP (Hewlett-Packard) C100 - page 3

    C100_110-160_180.FB 1 Tue Jul 16 06:36:50 1996 1 Upgrading your Model C100/1 10 to a Model C160 or C180 Upgrading your Model C100/110 to a Model C160 or C180 Y our upgrade kit contains a Main T ray Assembly , which, when installed, upgrades your Model C100/1 10 to a Model C160/C180. NOTE: Installing this upgrade in your Model C100 or Model C110 doe ...

  • HP (Hewlett-Packard) C100 - page 4

    C100_110-160_180.FB 2 Tue Jul 16 06:36:50 1996 2 Preparing Y our Workstation Preparing Your Workstation Before starting the upgrade, use the following procedure to prepare the workstation: 1 The workstation must be running HP-UX 10.20 or later to accommodate the C160/C180 upgrade. If the workstation is running a version of HP-UX lower than 10.2, up ...

  • HP (Hewlett-Packard) C100 - page 5

    C100_110-160_180.FB 3 Tue Jul 16 06:36:50 1996 3 Preparing Y our Workstation 4 Next, you need to run the upgrade utility program to automatically convert the hardware paths stored in the system’s I/O configuration file. You should only run this utility if you are going to complete the rest of the hardware upgrade described in this document. Enter ...

  • HP (Hewlett-Packard) C100 - page 6

    C100_110-160_180.FB 4 Tue Jul 16 06:36:50 1996 4 Preparing Y our Workstation 5 If your system has an A4070B HCRX-8Z or an A4071B with the A4272A accel- erator graphics adapter installed enter the following commands to save the cur- rent versions of the /etc/ioconfig and /stand/ioconfig files: mv /etc/ioconfig /etc/ioconfig.old mv /stand/ioconfig /s ...

  • HP (Hewlett-Packard) C100 - page 7

    C100_110-160_180.FB 5 Tue Jul 16 06:36:50 1996 5 Preparing Y our Workstation 12 Unplug the power cord of the system unit, the monitor, and any peripheral devic- es from ac wall outlets. 13 Unplug the power cord from the back of the system unit. W ARNING: To avoid electrical shock, make sure you unplug the power cable from the wall outlet and the sy ...

  • HP (Hewlett-Packard) C100 - page 8

    C100_110-160_180.FB 6 Tue Jul 16 06:36:50 1996 6 Preparing Y our Workstation 14 Remove the floor stand from the system unit, as shown in Figure 1. Figure 1 Removing the Floor Stand 15 Lay the system unit on a flat surface, such as a table top. 16 Attach a static-grounding wrist strap to bare metal on the back of the system unit. ...

  • HP (Hewlett-Packard) C100 - page 9

    C100_110-160_180.FB 7 Tue Jul 16 06:36:50 1996 7 Removing the Main T ray Assembly Removing the Main Tray Assembly Once you have prepared the workstation, you need to remove the main tray from the system unit, as described in the following procedure: 1 Completely loosen the four thumb screws on the rear of the system unit, as shown in Figure 2. Figu ...

  • HP (Hewlett-Packard) C100 - page 10

    C100_110-160_180.FB 8 Tue Jul 16 06:36:50 1996 8 Removing Memory Modules Removing Memory Modules After removing the main tray from the system, you must remove the mem- ory modules from the original C100/1 10 CPU board, as described in the fol- lowing procedure: 1 Locate the memory modules on the C100/C110 CPU board, as shown in Figure 3. Figure 3 M ...

  • HP (Hewlett-Packard) C100 - page 11

    C100_110-160_180.FB 9 Tue Jul 16 06:36:50 1996 9 Removing Memory Modules 2 To remove a memory module, push the ejector tabs on each side of the module. Lift the memory module up and out of the connector and place it on a static-free surface. Figure 4 shows how to remove a memory module. Figure 4 Removing a Memory Module ...

  • HP (Hewlett-Packard) C100 - page 12

    C100_110-160_180.FB 10 Tue Jul 16 06:36:50 1996 10 Removing Option Boards Removing Option Boards NOTICE: Any option boards that are supported by the new C160/180 system should be installed in the same slot number in the new main tray . If your C100/1 10 system has any option boards installed, you must remove them from the original C100/1 10 main tr ...

  • HP (Hewlett-Packard) C100 - page 13

    C100_110-160_180.FB 11 Tue Jul 16 06:36:50 1996 11 Removing Option Boards 2 Slide the EISA slider to the side to remove it, as shown in Figure 6. 3 Remove the screw from the EISA retainer, as shown in Figure 6 4 Grasp the option board by the edge with both hands and pull it straight out from its slot. Repeat this step for each option board. 5 Set t ...

  • HP (Hewlett-Packard) C100 - page 14

    C100_110-160_180.FB 12 Tue Jul 16 06:36:50 1996 12 Installing Memory Modules Installing Memory Modules Install the memory modules in the C160/C180 CPU board in the new main tray , as described in the following procedure: 1 Locate the memory connectors on the C160/C180 CPU board, as shown in Figure 7. The C160/C180 CPU has 12 memory slots, labeled 0 ...

  • HP (Hewlett-Packard) C100 - page 15

    C100_110-160_180.FB 13 Tue Jul 16 06:36:50 1996 13 Installing Memory Modules T able 1 Model C160/C180 Allowable Memory Configurations Config. No. Pair 0 Pair 1 Pair 2 Pair 3 Pair 4 Pair 5 T otal MB AB ABABABABAB 1 16 16 32 2 16 16 16 16 64 3 16 16 16 16 16 16 96 4 16 16 16 16 16 16 16 16 128 5 16 16 16 16 16 16 16 16 16 16 160 6 16 16 16 16 16 16 ...

  • HP (Hewlett-Packard) C100 - page 16

    C100_110-160_180.FB 14 Tue Jul 16 06:36:50 1996 14 Installing Memory Modules 25 32 32 32 32 32 32 32 32 32 32 320 26 32 32 32 32 32 32 32 32 32 32 16 16 352 27 32 32 32 32 32 32 32 32 32 32 32 32 384 28 64 64 128 29 64 64 16 16 160 30 64 64 16 16 16 16 192 31 64 64 16 16 16 16 16 16 224 32 64 64 16 16 16 16 16 16 16 16 256 33 64 64 16 16 16 16 16 1 ...

  • HP (Hewlett-Packard) C100 - page 17

    C100_110-160_180.FB 15 Tue Jul 16 06:36:50 1996 15 Installing Memory Modules 49 64 64 64 64 256 50 64 64 64 64 16 16 288 51 64 64 64 64 16 16 16 16 320 52 64 64 64 64 16 16 16 16 16 16 352 53 64 64 64 64 16 16 16 16 16 16 16 16 384 54 64 64 64 64 32 32 320 55 64 64 64 64 32 32 16 16 352 56 64 64 64 64 32 32 16 16 16 16 384 57 64 64 64 64 32 32 16 1 ...

  • HP (Hewlett-Packard) C100 - page 18

    C100_110-160_180.FB 16 Tue Jul 16 06:36:50 1996 16 Installing Memory Modules 73 64 64 64 64 64 64 32 32 32 32 32 32 576 74 64 64 64 64 64 64 64 64 512 75 64 64 64 64 64 64 64 64 16 16 544 76 64 64 64 64 64 64 64 64 16 16 16 16 576 77 64 64 64 64 64 64 64 64 32 32 576 78 64 64 64 64 64 64 64 64 32 32 16 16 608 79 64 64 64 64 64 64 64 64 32 32 32 32 ...

  • HP (Hewlett-Packard) C100 - page 19

    C100_110-160_180.FB 17 Tue Jul 16 06:36:50 1996 17 Installing Memory Modules 2 To install a memory module, close the ejector tabs on each side of the memory connector and line the memory module up with the guides, as shown in Figure 8. Make sure that the notched end of the memory module is toward the white ejector tab, or to the rear of the main tr ...

  • HP (Hewlett-Packard) C100 - page 20

    C100_110-160_180.FB 18 Tue Jul 16 06:36:50 1996 18 Installing Option Boards Installing Option Boards NOTICE: Any option boards that are supported by the new C160/180 system should be installed in the same slot number in the new main tray that they were installed in the old main tray . If you are installing a graphics adapter , read and understand t ...

  • HP (Hewlett-Packard) C100 - page 21

    C100_110-160_180.FB 19 Tue Jul 16 06:36:50 1996 19 Installing Option Boards Graphics Configuration Restrictions The system supports only four graphics displays at a time. A “display” is a video output port or connector . For example, the Dual V isualize Enhanced Graphics Card (A4451A) is a dual display card. It has two external video connectors ...

  • HP (Hewlett-Packard) C100 - page 22

    C100_110-160_180.FB 20 Tue Jul 16 06:36:50 1996 20 Installing Option Boards Option Board Installation If you removed option boards from the C100/1 10 main tray , use this proce- dure to install them in the new C160/C180 main tray . Otherwise, skip to the next section. 1 Press the fan release clip and rotate the fan, as shown in Figure 9. Figure 9 R ...

  • HP (Hewlett-Packard) C100 - page 23

    C100_110-160_180.FB 21 Tue Jul 16 06:36:50 1996 21 Installing Option Boards 2 Remove the screw from the EISA retainer, and remove the EISA retainer, as shown in Figure 10. Figure 10 Removing the EISA Retainer and EISA Slider 3 Remove the EISA slider, as shown in Figure 10. Eisa Retainer Eisa Slider ...

  • HP (Hewlett-Packard) C100 - page 24

    C100_110-160_180.FB 22 Tue Jul 16 06:36:50 1996 22 Installing Option Boards 4 In the desired option slot, turn the blank plate’s locking knob counter-clockwise to unlock the plate, as shown in Figure 11. NOTE: The new main tray assembly contains a blank plate which is held in by a locking knob. Be sure to remove these components before attempting ...

  • HP (Hewlett-Packard) C100 - page 25

    C100_110-160_180.FB 23 Tue Jul 16 06:36:50 1996 23 Installing Option Boards 6 Slide the option board into the slot. Make sure that the hole in the board’s handle aligns with the pin on the back panel, as shown in Figure 12. Figure 12 Installing an Option Board 7 Press in firmly on both ends of the option board at the same time to make sure that i ...

  • HP (Hewlett-Packard) C100 - page 26

    C100_110-160_180.FB 24 Tue Jul 16 06:36:50 1996 24 Installing Option Boards 8 Replace the EISA retainer and its screw, as shown in Figure 13. 9 Replace the EISA slider, as shown in Figure 13 Figure 13 Installing the EISA Retainer and EISA Slider EISA Retainer EISA Retainer EISA Slider ...

  • HP (Hewlett-Packard) C100 - page 27

    C100_110-160_180.FB 25 Tue Jul 16 06:36:50 1996 25 Installing Option Boards 10 Rotate the fan back into place and firmly push it into the rear panel firmly until the clip snaps into place, as shown in Figure 14. Figure 14 Securing the Fan ...

  • HP (Hewlett-Packard) C100 - page 28

    C100_110-160_180.FB 26 Tue Jul 16 06:36:50 1996 26 Installing the New Main T ray Assembly Installing the New Main Tray Assembly Install the new C160/C180 main tray assembly , as described in the following procedure: 1 Align the main tray assembly with the chassis and slide it into place, as shown in Figure 15. Figure 15 Installing the New Main Tray ...

  • HP (Hewlett-Packard) C100 - page 29

    C100_110-160_180.FB 27 Tue Jul 16 06:36:50 1996 27 Installing the New Main T ray Assembly 5 Remove any external SCSI terminators from the rear of the old main tray and in- stall them on the SCSI connectors on the rear of the system. 6 Use a small flat blade screwdriver to gently pry the old model number label from the front of the system. Remove th ...

  • HP (Hewlett-Packard) C100 - page 30

    C100_110-160_180.FB 28 Tue Jul 16 06:36:50 1996 28 Installing the New Main T ray Assembly 7 Replace the system unit in the floor stand, as shown in Figure 17. Figure 17 Installing the Floor Stand ...

  • HP (Hewlett-Packard) C100 - page 31

    C100_110-160_180.FB 29 Tue Jul 16 06:36:50 1996 29 Installing the New Main T ray Assembly 8 Reconnect the power cables and any other cables that you disconnected when opening the workstation. If you do not have a supported graphics adapter , connect your monitor ’ s 15-pin connector to the 15-pin connector on the EVC adapter cable which came with ...

  • HP (Hewlett-Packard) C100 - page 32

    C100_110-160_180.FB 30 Tue Jul 16 06:36:50 1996 30 Installing the New Main T ray Assembly 11 The system cycles through all of the available monitor types one at a time. When you can see a message similar to the following clearly and litigable, select that monitor type by pressing Enter. MONITOR INFORMATION Path Slot Head Type Size Freq Class ------ ...

  • HP (Hewlett-Packard) C100 - page 33

    C100_110-160_180.FB 31 Tue Jul 16 06:36:50 1996 31 Installing the New Main T ray Assembly 15 At the prompt, enter the following command to enter the configuration menu: co 16 Configure the console path for the built-in graphics with the following syntax: mo graphics(0) 17 Power off the system. 18 Power on the system. After you install a new CPU boa ...

  • HP (Hewlett-Packard) C100 - page 34

    C100_110-160_180.FB 32 Tue Jul 16 06:36:50 1996 32 Installing the New Main T ray Assembly ...

Fabbricante HP (Hewlett-Packard) Categoria Printer

I documenti che otteniamo dal fabbricante del dispositivoHP (Hewlett-Packard) C100 possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici HP (Hewlett-Packard)
- manuali per l’uso C100
- schede prodotto HP (Hewlett-Packard)
- opuscoli
- o etichette energetiche HP (Hewlett-Packard) C100
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso HP (Hewlett-Packard) C100.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione HP (Hewlett-Packard) C100, manuali di manutenzione, brevi manuali o manuali utente HP (Hewlett-Packard) C100. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto HP (Hewlett-Packard) C100.

Manuali per l’uso simili

Manuale completo del dispositivo HP (Hewlett-Packard) C100, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare HP (Hewlett-Packard) C100 dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti HP (Hewlett-Packard) C100.

Il manuale per l’uso completo HP (Hewlett-Packard), dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale HP (Hewlett-Packard) C100 - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice HP (Hewlett-Packard) C100, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per HP (Hewlett-Packard) C100 che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo HP (Hewlett-Packard) C100 - che ci dovrebbe aiutare nei primi passi durante l'uso HP (Hewlett-Packard) C100
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del HP (Hewlett-Packard) C100
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio HP (Hewlett-Packard) C100 in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su HP (Hewlett-Packard) C100?

Utilizza il modulo sottostante

Se non hai risolto il problema con HP (Hewlett-Packard) C100 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con HP (Hewlett-Packard) C100 è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)