-
AT&T PARTNER Plus Communications System Release 3 - page 1
AT&T PARTNER ® Plus Communications System Release 3 Installation ...
-
AT&T PARTNER Plus Communications System Release 3 - page 2
Copyright © 1992 AT&T AT&T 518-455-213 All Rights Reserved Issue 1 Printed in U.S.A. June 1992 Notice Every effort was made to ensure that the information in this book was complete and accurate at the time of printing. However, information is subject to change. Federal Communications Commission (FCC) Interference Notice This equipment has ...
-
AT&T PARTNER Plus Communications System Release 3 - page 3
Contents Important Safety Instructions Overview An Example System Setup Required Parts Installation Guidelines ■ Telephones and Devices Combination Extensions ■ Using A Direct Connection Using a Bridging Adapter Installation Procedures ■ ■ ■ ■ ■ ■ ■ Installing the Control Unit and Modules Connecting Lines and Extensions Connecting ...
-
AT&T PARTNER Plus Communications System Release 3 - page 4
Important Safety Instructions Always follow these basic safety precautions when using the system: 1. Read and understand all instructions. 2. Follow all warnings and instructions marked on the product. 3. Never spill liquid on the product or drop objects into the ventilation slots and openings. Doing so may result in serious damage to the component ...
-
AT&T PARTNER Plus Communications System Release 3 - page 5
Installation Overview This guide explains how to install the system. It begins with an example system setup, then follows with an illustration of the components you need to install the system and general guidelines to consider before installation. Next, it provides step-by-step instructions for connecting and testing the components for initial inst ...
-
AT&T PARTNER Plus Communications System Release 3 - page 6
An Example System Setup The next page shows a control unit with two 206 modules and two 400 modules, giving the system a capacity of 12 outside lines and 12 extensions. Although your system may differ, this example will give you an idea of the types of equipment you can connect to it. In the example, system phones and industry-standard devices are ...
-
AT&T PARTNER Plus Communications System Release 3 - page 7
CONTROL UNIT EXTENSIONS Extension 10 Extension 18 Extension 11 Extension 12 Extension 17 Extension 16 Extension 15 Extension 13 Extension 14 An Example System Setup 3 ...
-
AT&T PARTNER Plus Communications System Release 3 - page 8
Required Parts You will have up to three types of system component packages; Figure 1 shows the contents of each package in the area marked by a dashed line. Check your packages to be sure you have the parts shown here (if not, call the appropriate support telephone number as instructed on the inside front cover). Control Unit MLS-34D Programming O ...
-
AT&T PARTNER Plus Communications System Release 3 - page 9
Installation Guidelines Telephones and Devices You can connect the following telephones and devices to the system: MLS- and MLC-Model System Phones. System phones require at least ■ two-pair wiring and are compatible with AT&T 4-pair SYSTIMAX™ wiring. Call Assistant Intercom Autodialers with Busy Indication ■ (MLS-CA24). You can connect a ...
-
AT&T PARTNER Plus Communications System Release 3 - page 10
Combination Extensions You can connect a standard device (such as a standard phone or an answering machine) on an extension by itself, or so that it shares an extension with another piece of equipment (either another standard device or a system phone). An extension with two devices connected to it is called a combination extension. You cannot insta ...
-
AT&T PARTNER Plus Communications System Release 3 - page 11
Installation Procedures Before installing the system, be sure you read the safety instructions on page ii. WARNING: There are no customer-serviceable components inside the system modules or backplane. There are hazardous voltages within that can cause severe or fatal personal injury. DO NOT OPEN THE MODULES. Installing the Control Unit and Modules ...
-
AT&T PARTNER Plus Communications System Release 3 - page 12
4 A) B) C) D) To power down the control unit, pull out the main circuit breaker on the control unit. On a PARTNER Plus 220V system, move the on/off switch to the “off” position (“O”). Press the AC power cord firmly into the power jack on the top right side of the backplane until it locks into place. Plug the other end of the power cord into ...
-
AT&T PARTNER Plus Communications System Release 3 - page 13
Connecting Lines and Extensions If extensions are not wired to any modular jacks, call a qualified service technician. 555-1343 1 2 3 4 555-1344 A) B) C) A) B) C) Test for dial tone at the network interface jacks before connecting outside lines to the control unit. For the test, connect a standard phone to the first network interface jack. Lift the ...
-
AT&T PARTNER Plus Communications System Release 3 - page 14
5 A) B) C) D) 6 A) B) C) Connect modular telephone cords to 206 module extension jacks, starting at the top extension jack on the leftmost module. Route each cord through the hook on the front of the module, and then push the cords through the space below the module and out through the back. Pull the cords from behind the backplane, leaving at leas ...
-
AT&T PARTNER Plus Communications System Release 3 - page 15
Connecting Caller ID Display Units To get Caller ID information for an extension, you must first subscribe to the service (on a per-line basis) from your local telephone company, then connect the units as described here. You must connect the Caller ID display unit directly to the line that supports Caller ID at the network interface jack. Additiona ...
-
AT&T PARTNER Plus Communications System Release 3 - page 16
Assembling System Phones You can either desk mount or wall mount a system phone. If the system phone is manufactured with a separate stand, you can use the stand to either wall mount the phone or raise the angle of the phone when desk mounting. (The stand is required for MLS-34D phones.) Alternatively, some system phones—such as the MLS-18D—are ...
-
AT&T PARTNER Plus Communications System Release 3 - page 17
Wall Mounting If you wall mount a display phone, the display may be difficult to read, so desk mounting is recommended. (Wall mounting instructions apply to corded MLS-model phones only. To wall mount an MLC-6 cordless phone, follow the instructions in the booklet provided with the phone.) Wall Mounting Phones with Separate Stands 1 2 3 Reverse the ...
-
AT&T PARTNER Plus Communications System Release 3 - page 18
2 A) B) C) 3 A) B) C) Unscrew the phone’s four mounting screws and lift the base of the phone off the top. CAUTION: Do not touch electrical circuitry. To do so will expose you to a risk of electrical shock and possibly damage the equipment. Turn the base of the phone upside down so that the phone base can be mounted parallel to the wall—and the ...
-
AT&T PARTNER Plus Communications System Release 3 - page 19
Connecting Paging, Music-On-Hold, and Call Reporting (SMDR) Devices SMDR Jack Only steps for connection to the processor module are provided here. Refer to Chapter 4 of the PARTNER Plus Programming and Use guide and the manufacturer’s instructions for additional information on installing, programming, and using these devices. Paging System 1 Inse ...
-
AT&T PARTNER Plus Communications System Release 3 - page 20
Connecting Intercom Autodialers Since the autodialer has a fixed stand, you may need to adjust the height of the system phone—by installing a stand—to match the height of the autodialer. Refer to Step 2 of “Desk Mounting” under “Assembling System Phones” for instructions. You can wall mount an Intercom Autodialer to work next to a wall- ...
-
AT&T PARTNER Plus Communications System Release 3 - page 21
Equipment Upgrades Adding New Modules 1 A) B) C) 2 A) B) 3 A) B) Power Jack Handle Tab 4 To power down the control unit, pull out the main circuit breaker. On a PARTNER Plus 220V system, move the on/off switch to the “off” position (“O”). To remove the cover, place one hand on the handle on the bottom front of the cover and place your other ...
-
AT&T PARTNER Plus Communications System Release 3 - page 22
5 A) To replace the cover, while holding the cover at an angle, gently move the top rear edge of the cover over the top of the control unit and match up the grooves where the top edge of the cover meets the backplane. Gently push the edge into place. B) Lower the bottom of the cover until it is secured in place. Replacing System Modules 1 A) B) C) ...
-
AT&T PARTNER Plus Communications System Release 3 - page 23
3 A) Connect the line and extension cords one at a time, making sure to place the correct cords into their corresponding jacks on the new module. B) To power up the control unit, push in the main circuit breaker. On a PARTNER Plus 220V system, move the on/off switch to the “on” position (“l”). 4 Check all green lights on the fronts of the m ...
-
AT&T PARTNER Plus Communications System Release 3 - page 24
Specifications Capacities System 206 Module Extension Jack ■ ■ ■ 12 outside lines via line jacks on ■ 2 outside lines ■ Maximum 2 devices per extension two 206 plus two 400 modules ■ 6 extensions jack, total REN on jack not to 24 extensions via extension jacks on four 206 modules 400 Module exceed 2.0* (System phone REN: 0.0 (zero)) ■ ...
-
AT&T PARTNER Plus Communications System Release 3 - page 25
SMDR Output ■ 1200 baud Format ■ No parity ■ 8 data bits ■ 2 stop bits Environmental ■ Mount on a wall at least 2 feet (0.6 meters) from the floor (wall mounting required) Requirements— ■ Locate within 5 feet (1.5 meters) of the network interface jacks and an electrical outlet not Control Unit controlled by a switch, using supplied 7- ...
-
AT&T PARTNER Plus Communications System Release 3 - page 26
518-455-213 Issue 1 June 1992 Graphics © 1988 ...
Hai una domanda su AT&T PARTNER Plus Communications System Release 3?
Utilizza il modulo sottostante
Se non hai risolto il problema con AT&T PARTNER Plus Communications System Release 3 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con AT&T PARTNER Plus Communications System Release 3 è probabile che voglia condividere il modo di risolverlo.