Italiano dropdown-ico

Manuale per l’uso Campbell Manufacturing TLX106

50 pagine 0.76 mb
Scarica

Vai alla pagina of 50

Summary
  • Campbell Manufacturing TLX106 - page 1

    TLX106 WEA THER STA TION INSTRUCTIO N M A NUA L 3/01 COPYRIGH T (c) 1993-2001 CA MPBELL SC IENTIFIC, INC. ...

  • Campbell Manufacturing TLX106 - page 2

    This is a blank page. ...

  • Campbell Manufacturing TLX106 - page 3

    Warranty and Assistance The TLX 106 WEATHE R STAT ION is warranted by C AMPBELL SCIENTIFIC , INC. to be free from defects in material s and workmanship under normal use and servi ce for twelve (12) months from date of s hipment unless s pecified otherwise. Bat teries have no warranty. C AMPBELL SCIENTIF IC, INC.'s obl igation under this wa rra ...

  • Campbell Manufacturing TLX106 - page 4

    This is a blank page. ...

  • Campbell Manufacturing TLX106 - page 5

    i TLX106 Weather Station Table of Contents 1. Preparation and Siting 1.1 Installation Tasks .................................................................................. 1-1 1.1.1 Indoors......................................................................................... 1-1 1.1.2 Outdoors ................................................. ...

  • Campbell Manufacturing TLX106 - page 6

    TLX106 Weather Station Table of Contents ii 4.6 Pyranometer .......................................................................................... 4-3 4.7 Sensor Verification and Clock Set.........................................................4-3 4.8 Sensor Schematics ........................................................................... ...

  • Campbell Manufacturing TLX106 - page 7

    TLX106 Weather Station Table of Contents iii 5.3-1 ProLine software provides an easy-to-use message editor ................ 5-7 5.3-2 The available options provided by the source menu are shown ........ 5-8 5.3-3 When the weather st ation source has been chosen, s everal meteorological condi tions reported in vari ous units are provided under the f ...

  • Campbell Manufacturing TLX106 - page 8

    This is a blank page. ...

  • Campbell Manufacturing TLX106 - page 9

    1-1 Section 1. Preparation and Siting These guidelines apply to several Campbell Scientific weather stations. 1.1 Installation tasks 1.1.1 I ndoor s • Immediately upon receipt of your shipment… ⇒ Open shipping cart ons. ⇒ Check contents agai nst invoice. Contact CSI immediately about any shortages . • Several days pri or to the planned in ...

  • Campbell Manufacturing TLX106 - page 10

    Section 1. Preparation and Siting 1-2 1.2.1 Tools for Tower Installati on All Towers Shovel Rake Open end wrenches: 3/8", 7/ 16", ½", (2) 9/16" Magnetic compass 6' Step ladder TLX 106 Tower Tape measure (12’ to 20’) Claw hammer Level (24” to 36” ) Hand saw Materials for concret e form: (4) 1" x 2" x 12&qu ...

  • Campbell Manufacturing TLX106 - page 11

    Section 1. Preparation and Siting 1-3 1.2.3 Suppl i es for Power and Communications Options AC Power Wire, conduit, and j unction boxes as needed Phone Modem Hayes compatib le calling modem f o r PC Phone line to weat her station or juncti on box Short-Ha ul Modem 4 Conductor communicati ons cable from PC t o weather station or junct ion box 6&apos ...

  • Campbell Manufacturing TLX106 - page 12

    Section 1. Preparation and Siting 1-4 Situati ons to avoid include: • large indust rial heat sources • rooftops • steep slop es • sheltered ho llows • high vegetati on • shaded areas • swamps • areas where snow drifts occur • low places holding standing water after rains eight of tree ogan Uta MADE IN USA FIGURE 1.3-1. Effec t of ...

  • Campbell Manufacturing TLX106 - page 13

    Section 1. Preparation and Siting 1-5 (Section 1.4.1). A general map showing magnetic decli nation for the contiguous United St ates is shown i n Figure 1.4-1. Declination angles east of True North are considered negative, and are s ubtracted from 0 degrees to get True North as shown Figure 1.4-2. Declinat ion angles west of True Nor th ar e con-si ...

  • Campbell Manufacturing TLX106 - page 14

    Section 1. Preparation and Siting 1-6 Telephone numbers: Phone Number Baud Rat es 303-273-8672 2400 303-273-8673 1200 303-273-8678 1200 Upon carrier-signal det ection, press Ret urn once or twice. If you are using one of the commercial numbers, the following prompts will appear. Type the responses shown (followed by press ing RETURN): GLDSV1> c ...

  • Campbell Manufacturing TLX106 - page 15

    Section 1. Preparation and Siting 1-7 Exiting: Press "Cntrl-Z" to exit GEOMAG. When the main menu reappears eit her select another option or type "X " to log out. If you used one of the commercial numbers , the GLDSV1> prompt wil l reappear. Type "LO" to disconnect . Use of GEOMAG i s free (except for telephone char ...

  • Campbell Manufacturing TLX106 - page 16

    Section 1. Preparation and Siting 1-8 FIGURE 1.4-3. Dec lination Angles West of True North Are Added to 0 to Get True North ...

  • Campbell Manufacturing TLX106 - page 17

    2- 1 Section 2. TLX106 Tower Installation Do not install near power lines. If any part o f the to wer comes in contact with power lines you could be KILLED. Contact local utilities for t he location of buried utility lines before digging or driving grounding rods. Do not fit the 3 meter TLX106 Tower sections together until the appropriate time. Onc ...

  • Campbell Manufacturing TLX106 - page 18

    Section 2. TLX106 Tower Installation 2-2 2.1 Base Installation 2.1.1 Suppl i e d Components (3) ½ inch L-Bolts (9) ½ inch Nuts (1) Anchor Template Refer to Sect ion 1 for components suppli ed by installer. 2.1.2 Installation 1. The TLX106 Tower attaches to a user supplied concrete foundation constructed as shown in Figure 2.1-2. 2. Construct the ...

  • Campbell Manufacturing TLX106 - page 19

    Section 2. TLX106 Tower Installation 2-3 D TO O OLT O O T D LL T TLT OT O FIGURE 2.1-2. TLX106 T ower Base Installation 2.2 Tower Installation 2.2.1 Suppl i e d Components (1) Upper Tower Section (Tapered) (1) Lower Tower Section (6) ½ inch Was hers (1) 12 foot 12 AWG Ground Cable (1) Tower Cap (1) 20' communications cable (1) 20' power ...

  • Campbell Manufacturing TLX106 - page 20

    Section 2. TLX106 Tower Installation 2-4 4. Cut and save a 9 inch piece of 12 AW G ground wire from the 12 foot length provided. Thread t he remaining 11 foot ground wire through the tower. Secure all w iring so it does not slip back into the tower or conduit . 5. Place the tower cap over the tower end. 6. Raise the tower on a still da y . Place a ...

  • Campbell Manufacturing TLX106 - page 21

    Section 2. TLX106 Tower Installation 2-5 2.3.2 Gr oundi ng Pr ocedure Ground the tower as shown in Figure 2.2-1. 1. Place the ground rod clamp on the rod. Secure it about 3 inches from the top. Do this before t he rod is driven into the ground. Be careful not to damage the clamp with the hammer 2. Taking care not to damage power or communicat ions ...

  • Campbell Manufacturing TLX106 - page 22

    This is a blank page. ...

  • Campbell Manufacturing TLX106 - page 23

    3-1 Section 3. TLX106 Instrumentation Installation The weather station datalogger, power supply, sensor connection panel, communications devices, and data retrieval peripherals are mounted in the TLX106 enclosure at the locations shown in Figure 3-1. Components include: (1) TLX106 Enclosure (1) 4 unit Desiccant Pack (1) Flat Point Screw D river (1) ...

  • Campbell Manufacturing TLX106 - page 24

    Section 3. TLX106 Instr umentation Installation 3-2 3.1 Enclosure, Datalogger, Power Supply 3.1.1 Battery Option Installation S FIGURE 3.1-1. Rec hargeable Power Mounting and Connections a) Sealed Rechargeable Battery Option: Install the kit as shown in Figure 3.1-1. An unregulated sola r panel or 17 to 24 VAC must be us ed with the rechargeable ba ...

  • Campbell Manufacturing TLX106 - page 25

    Section 3. TLX106 Instr umentation Installation 3-3 The solar panel should be oriented to receive maximum insolation over the course of the year. Suggested tilt angles (referenced to the horizontal plane) are listed below. Site Latitude Tilt Angle 0 to 10 degrees 10 degrees 11 to 20 Latitude + 5 degrees 21 to 45 Latitude + 10 degrees 46 to 65 Latit ...

  • Campbell Manufacturing TLX106 - page 26

    Section 3. TLX106 Instr umentation Installation 3-4 O R T H FIGURE 3.1-3. Mounting and G rounding the TLX106 Enclosure c) Slide the enclosure to the top of the TLX106 tower. Position it on the north side of the tow er (northern hemisphere). The top of the enclosure shoul d be flush with the top of t he tower, with the widt h of the sensor arm ext e ...

  • Campbell Manufacturing TLX106 - page 27

    Section 3. TLX106 Instr umentation Installation 3-5 Earth Ground Stand off Connector #4 Sensors TEMP CS615 TEMP RAIN (PRECIP) TEMP / RH SOLAR RADIATION COMM WS/WD SDI 12 GYP BLOCK #2 #6 #7 #5 #1 #3 #8 CS I/O POWER CABLE PORT STAND OFF COAXIAL CONNECTION FIGURE 3.2-1. Pos ition of Sensor Bulkhead Connectors 3) Replace the protective connector cover ...

  • Campbell Manufacturing TLX106 - page 28

    Section 3. TLX106 Instr umentation Installation 3-6 If you received a telecommunications kit separate from the TLX106 Enclosure, follow the "In ternal Installation" pr o cedures outlined b elow. 3.3.1 Phone Modems Phone modems enable communi cations between the TLX106 Encl osure and a Hayes compatibl e modem in your PC over a dedicated ph ...

  • Campbell Manufacturing TLX106 - page 29

    Section 3. TLX106 Instr umentation Installation 3-7 3.3.1.2 External Installation The following modem kit components are used to make the external connections: (1) Direct Burial Splice Kit (1) 20 foot Telephone Pat ch Cord with Connect or 1) Connect t he 20 foot patch cord to the connector marked "comm" on the external back panel, under t ...

  • Campbell Manufacturing TLX106 - page 30

    Section 3. TLX106 Instr umentation Installation 3-8 3. Connect the SC932C 9-pi n port to the internal TLX106 Enclos ure 9-pin port with the bl ue ribbon cable provided. 4. Wire the Rad Modem to the TLX106 Enclos ure with the 12 inch patch cord. Match wire label s to wiring panel la bels on both the TLX106 Enclosure and the Rad Modem (+X MT to +XMT, ...

  • Campbell Manufacturing TLX106 - page 31

    Section 3. TLX106 Instr umentation Installation 3-9 - RCV (white) - RCV (black) + RCV (green) + RCV (red) + XMT (red) + XMT (green) - XMT (black) - XMT (white) - RCV + RCV + XMT - XMT BLACK RED GREEN WHITE 2 1 3 4 - RCV (black) + RCV (red) + XMT (green) - XMT (white) 2 1 3 4 SRM-5A Surge Protector PC User Supplied Cable Splices ET106 ENCLOSURE ET10 ...

  • Campbell Manufacturing TLX106 - page 32

    Section 3. TLX106 Instr umentation Installation 3-10 D O N O T E A T U N IT E D D E S IC C A N T S -G A T E S 101CHRISTINE, BELEN, NEW MEXICO 87002 DESI PAK SPECIFICATION MIL-D-3464 TYPE I &II REACTIVATION TIME IN-BAG 16 HOURS AT 250 F DESICCANT ACTIVATED BAGGED FOR CONTENTS 4 UNITS PACKAGE USE AND STATIC DEHUMIDIFICATION D O N O T E A T U N IT ...

  • Campbell Manufacturing TLX106 - page 33

    4-1 Section 4. TLX106 Sensor Arm Installation 4.1 Components (1) TLX106 Sensor A rm (1) Met One 034A Wi nd Sensor (1) 034A Mounting Shaft (1) Radiatio n Shield 4.2 Installation Install t he TLX106 Sensor Arm after the Encl osure is mounted low on the Tower. You may need to temporari ly remove communications opti on. Mount the sensor arm as shown in ...

  • Campbell Manufacturing TLX106 - page 34

    Section 4. TLX106 Sensor Arm Installation 4-2 4.3 Sensor Connection Refer to Sect ion 3 for sensor connection det ails. 4.4 034A Wind Sensor Installation Install t he 034A Wind Sensor as shown in Figure 4.4-1 afte r the sensor arm is securely instal led. The wind vane is orient ed after the datalogger has been programmed, and the location of True N ...

  • Campbell Manufacturing TLX106 - page 35

    Section 4. TLX106 Sensor Arm Installation 4-3 4.5 RH and Temperature Radiation Shield Mount the radiation s hield to the sens or arm as shown in Figure 4.4-1. Remove yellow cap. Place the RH and temperature ass embly inside the shield shaft. Attach the sh ield to the sensor arm with th e two screws. 4.6 Pyranometer Level the pyranometer as indi cat ...

  • Campbell Manufacturing TLX106 - page 36

    Section 4. TLX106 Sensor Arm Installation 4-4 Input Location Parameter Normal Range 1 Enclosure Close to air Temperature (°C) temperature 3 Solar Radi ation 0 to 1.2 kW m -2 (kW m -2 ) 4 Air Temperature (°C ) -40° to +50° 5 RH (%) 0 t o 100% 6 Wind Speed (mph) 0 to 110 mph 7 Rain Fal l (inches) 0 to .2 8 Wind Di rection (°) 0 to 359 10 Batte r ...

  • Campbell Manufacturing TLX106 - page 37

    Section 4. TLX106 Sensor Arm Installation 4-5 1 2 3 4 5 6 Air T emperature and Relative Humidity Sensor Connector Pin Datalogger Relative Humidity (0-1VDC) Air T emperature (0-1VDC) 12V Switched Supply Not Used Analog Ground Shield 1 2 3 4 5 6 1 H 1 L 12VDC Switched Supply AG G FIGURE 4.8-1. Sc hematic of HMP45C-LC RH and Temperature Probe and Conn ...

  • Campbell Manufacturing TLX106 - page 38

    Section 4. TLX106 Sensor Arm Installation 4-6 Solar Radiation Sensor 40.2 - 90.2 OHM Connector Pin Datalogger 1 3 2 Not Used Not Used Not Used 3 H 3 L G Shield 4 5 6 1 2 3 4 5 6 FIGURE 4.8-3. Sc hematic of LI200X-LC Solar Radiation Sensor and Connector #3 1 Not Used Connector Pin Magnetically Activated Reed Switch Tipping Rain Buck et Not Used Not ...

  • Campbell Manufacturing TLX106 - page 39

    5-1 Section 5. Software Installation and Settings 5.1 Measure Sensors and Process Dat a A pre-written d atalogger program (PN 14079) comes in stalled in the TLX106. This program sets the scan rat e, measures the sens ors, processes inter n ally and stores the data. This program will b e f actory corrected for the station’s latitude, longitude, el ...

  • Campbell Manufacturing TLX106 - page 40

    Section 5 . Software Ins tallation and Settings 5-2 Here again the Comm unications Ena bled button must be selected. Then select the proper M odem Type and zer o out the Extra R esponse Time. Then press Apply and continue to the next s tep. Here again the Communications Ena bled must be selected. Then a dd the appropriate Phone Number . Then zero o ...

  • Campbell Manufacturing TLX106 - page 41

    Section 5 . Software Ins tallation and Settings 5-3 The final terminati on must be t o a CR10X-TD logge r. The Proline wil l default to wor k with a logger named ‘lgr1’, but yo u can change thi s default if you w ant to name you r logger somethin g else. Change the logger name here and then refer to t he RDE extra settings to make sure you chan ...

  • Campbell Manufacturing TLX106 - page 42

    Section 5 . Software Ins tallation and Settings 5-4 If not already s tarted, start t he LoggerNet s erver by double clic king the blue icon. Then start the Cont rol Panel. It should automati cally connect to the server. Then select the appropriate logger an d click on the Connectio n bar. The co m puter sh ould initiate and connect with the station ...

  • Campbell Manufacturing TLX106 - page 43

    Section 5 . Software Ins tallation and Settings 5-5 “ Keep Logger On Line” This is used to force LoggerN et to stay connected to the statio n the entire time the LoggerNet serve r is open. This is desirable when there are short collection intervals. The default sett ings are shown bel ow. The Host is the computer that is running LoggerN et. Thi ...

  • Campbell Manufacturing TLX106 - page 44

    Section 5 . Software Ins tallation and Settings 5-6 Now reopen Net Admin and go to the l ogger previ ously set up. Now we will check to see if the Table Definitions have updated correctly by going to the Data Co llectio n tab. It could look like the following picture. Now select t he Scheduled Collection t ab again. Here you need to enable the sche ...

  • Campbell Manufacturing TLX106 - page 45

    Section 5 . Software Ins tallation and Settings 5-7 5.3 Create Mes sage Perform the fol lowing steps us ing the Mess age Editor provi ded in ProLine So f tware: 1. Type the message in t he area indicated in F igure 5.3-1. 2. Move cursor t o where you want dat a inserted. 3. Select a s ource from the Source pul l-down menu (Fi gure 5.3-2). 4. Select ...

  • Campbell Manufacturing TLX106 - page 46

    Section 5 . Software Ins tallation and Settings 5-8 FIGURE 5. 3-2. The avai lable options provided by the source menu are shown. FIGURE 5 .3-3. When the w eather stat ion sourc e has been chos en, several meteorologic al conditio ns reported i n various un its are provid ed under the field menu. ...

  • Campbell Manufacturing TLX106 - page 47

    6-1 Section 6. Maintenance and Troubleshooting These guidelines apply to several Campbell Scientific weather stations. 6.1 Maintenance Proper maintenance of weather s tation components is essential to obtain accurate data. Equipment must be in good operating condition, which requires a program of regular inspection and mai ntenance. Routine and si ...

  • Campbell Manufacturing TLX106 - page 48

    Section 6. Maintenance and Tr oubleshooting 6-2 6.1.4 Sensor Mai ntenance Sensor maint enance should be performed at regular interval s, depending on the desired accuracy and the conditions of use. A s uggested maintenance schedule is outlined below. 1 w eek • Check the py ranometer f or level and contamination. Gen tly clean, if needed. • Visu ...

  • Campbell Manufacturing TLX106 - page 49

    Section 6. Maintenance and Tr oubleshooting 6-3 2. Punch a very small hole in the bottom of the can. 3. Place the can in the top funnel of the rain gage and pour 16 fluid ounces (1 pint) o f water in to the can. (A 16 oz. so f t drink bottle filled to with in 2.5 inches of the top may be us ed for a rough field calibration. An exact volume will all ...

  • Campbell Manufacturing TLX106 - page 50

    Section 6. Maintenance and Tr oubleshooting 6-4 At the computer: D. Mak e sure the Station File is con f ig ured correctly. E. Check the cable(s) between the serial port and the modem. If cables have not been purchased through Ca mpbell Scientifi c, check for the following configuration us ing an ohm meter: 25-pin serial port: computer end modem en ...

Fabbricante Campbell Manufacturing Categoria Weather Radio

I documenti che otteniamo dal fabbricante del dispositivoCampbell Manufacturing TLX106 possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Campbell Manufacturing
- manuali per l’uso TLX106
- schede prodotto Campbell Manufacturing
- opuscoli
- o etichette energetiche Campbell Manufacturing TLX106
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Campbell Manufacturing TLX106.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Campbell Manufacturing TLX106, manuali di manutenzione, brevi manuali o manuali utente Campbell Manufacturing TLX106. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Campbell Manufacturing TLX106.

Manuali per l’uso simili

Manuale completo del dispositivo Campbell Manufacturing TLX106, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Campbell Manufacturing TLX106 dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Campbell Manufacturing TLX106.

Il manuale per l’uso completo Campbell Manufacturing, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Campbell Manufacturing TLX106 - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Campbell Manufacturing TLX106, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Campbell Manufacturing TLX106 che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Campbell Manufacturing TLX106 - che ci dovrebbe aiutare nei primi passi durante l'uso Campbell Manufacturing TLX106
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Campbell Manufacturing TLX106
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Campbell Manufacturing TLX106 in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Campbell Manufacturing TLX106?

Utilizza il modulo sottostante

Se non hai risolto il problema con Campbell Manufacturing TLX106 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Campbell Manufacturing TLX106 è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)