Italiano dropdown-ico

Manuale per l’uso Alloy RNS5

22 pagine 1.14 mb
Scarica

Vai alla pagina of 22

Summary
  • Alloy RNS5 - page 1

    Alloy RNS5/8 Industrial 5-port/8-port Ethernet Rail Switch User’s Manual Rev.1.1 20-Jan-2005 ...

  • Alloy RNS5 - page 2

    Content Introduction ......................................................... 1 Features ................................................................... 1 Package Checklist .................................................... 2 Hardware Description ......................................... 3 Dimensions ......................................... ...

  • Alloy RNS5 - page 3

    Introduction Industrial environments are usually more demanding than office environments. Harsh temperature conditions, vibration, dust, etc. all put higher demands on the quality and reliability of your networking equipment. To survive harsh industrial environments, Alloy provides you with the RNS5/8 Series Industr ial 5-port/8-port 10/100Mbps Eth ...

  • Alloy RNS5 - page 4

    Package Checklist Alloy RNS5/8 Industrial 5-port/8-port Et hernet Rail Switches are packaged with the following items:  RNS5/8 Industrial 5-port/8-port Ethernet Rail Switch  One DIN-Rail clip (attached to the RNS5/8)  One wall mounting plate and six screws  User’s manual CD-ROM RNS5/8 Switch User’s Manual CD-ROM W a l l M o u n t i ...

  • Alloy RNS5 - page 5

    Hardware Description D i m e n s i o n s RNS5/8 Industrial 5-port/8-port Ethernet Rail Switch dimensions (W x H x D) are 54mm x 135mm x 105mm F r o n t P a n e l The Front Panel of the RNS 5 Industrial 5-port Ethernet Rail Switch is shown in Figure A. LED Indicators UTP Ports Figure A. Front Panel of the RNS5 In dustrial 5-port Ethernet Rail Switch ...

  • Alloy RNS5 - page 6

    The Front Panel of the RNS 8 Industrial 8-port Ethernet Rail Switch is shown in Figure A. LED Indicators UTP Ports Figure A. Front Panel of the RNS8 In dustrial 8-port Ethernet Rail Switch 4 ...

  • Alloy RNS5 - page 7

    Bottom View The bottom view of the RNS5/8 Industr ial 5-port/8-port Et hernet Rail Switch consists of one terminal block connector with two DC power inputs, Alarm output and one DC IN power jack for an additional AC/DC power adapter. Figure B. Bottom view of the RNS5/8 Indu strial 5-port/8-port Ethernet Rail Switch Wiring the DC Power Inputs Follow ...

  • Alloy RNS5 - page 8

    L E D I n d i c a t o r s There are 5 diagnostic LEDs and 8 Port LEDs located on the Front panel of the RNS5 Industrial Ethernet Rail Switch. These LED indicators provide administrators with real-time system stat us. Table 1 gives descriptions of the functions of each LED indicator. LED Status Description Green Power is on. PWR Off No power is bein ...

  • Alloy RNS5 - page 9

    Port LED Status Description Orange The port is operating in full-duplex mode. Blinking orange Collision of Packets occurring. Off The port is in half-duplex mode or no device is attached. Green A network device is detected. Blinking green The port is transmitting or receiving packets from the TX device. Port Status (Port 1 to Port 4) Off No device ...

  • Alloy RNS5 - page 10

    Blinks The port is transmitting or receiving packets from the TX device. Off No device is attached. Orange The port is operating in full-duplex mode. Blinks Collision of packets occurs. FDX/COL of Port 7/8 Off The port is in half-duplex mode or no device is attached. Port LED Status Description Orange The port is operating in full-duplex mode. Blin ...

  • Alloy RNS5 - page 11

    Fig C Straight Through Cabling Schematic Fig C-1 Cross Over Cabling Schematic All ports of RNS5/8 support the auto-MD I/MDI-X function. When you use an Ethernet cable to connect other devices, such as computers, swit ches or hubs, pin 1, 2, 3, and 6 of the 8-pin RJ45 c onnector are used to communicate with the connected devices. Pin1, 2, 3, and 6? ...

  • Alloy RNS5 - page 12

    Mounting Installation DIN-Rail Mounting The DIN-Rail clip is already attached to the RNS5/8 when packaged. If the DIN-Rail clip is not screwed on the RNS5/8, follow the instructions and the figure below to attach the DIN-Rail clip to the RNS5/8. Rear Panel of the RNS5/8 DIN-Rail Clip 1. Use the screws to attach the DIN-Rail clip to the rear panel o ...

  • Alloy RNS5 - page 13

    Follow the steps below to mount t he RNS5/8 to the DIN-Rail track: 1. First, insert the upper end of the DIN-Rail clip into the back of the DIN-Rail track from its upper side. 2. Lightly push the bottom of the DIN-Rail clip into the track. 3. Check if the DIN-Rail clip is tightly attached on the track. 4. To remove the RNS5/8 from the track, revers ...

  • Alloy RNS5 - page 14

    Wall Mounting Follow the steps below to install the RNS5/8 with the wall mounting plate. 1. To remove the DIN-Rail clip from the RNS5/8, loosen t he screws from the DIN-Rail clip. 2. Place the wall mounting plate on the rear panel of the RNS5/8. 3. Use the screws to tighten the wa ll mounting plate ont o the RNS5/8. 4. Use the hook holes at the cor ...

  • Alloy RNS5 - page 15

    Hardware Installation The following figure illustrates a typi cal application of RNS5/8 Industrial 5-port/8-port Ethernet Rail Switch. Installation and Testing 1. Take your RNS5/8 Industrial 5-port/8- port Rail Switch out of the package box. 2. Check if the DIN-Rail clip is attached to the RNS5/8. If the DIN-Rail clip is not attached to the RNS5/8, ...

  • Alloy RNS5 - page 16

    4. Pull the terminal bloc k off the RNS5/8 and wire the power lines . Refer to the Wiring the DC Power Inputs section for how to wire the power inputs. 5. PWR1 and PWR2 dual power inputs can be connected to power sources simultaneously. When the primary power s ource fails (the default setting is PWR1), the system wil l automatically switch to the ...

  • Alloy RNS5 - page 17

    10. Power on the host, activate the Command Line mode, and ping the connected Ethernet device to see if it will respond. 10.1 To enable the “Command Line mode”, click on Run in the Start menu, type Command , and click on OK to continue. 10.2 Type ping 192.168.1.1 command to check the connection. Here we use IP address 192.168.1.1 as an example. ...

  • Alloy RNS5 - page 18

    12. Power on the host, activate the Command Line mode, and ping the connected Ethernet device by typing “ping –t 192.168.1.1” command to see if it will respond. 13. The parameter ”t” allows you to cont inue to ping the network device, as shown in the figure below. Before you continue, make sure that both PWR1 and PWR2 are successfully con ...

  • Alloy RNS5 - page 19

    Trouble shooting  Make sure you are using the correct VDC power supplies (12 to 48 VDC) or power adapters. Do not use power adapt ers with DC output over 48V. It will damage the device.  Select Ethernet cables with specifications suitable for your applications to set up your system. Ethernet cables are cat egorized into unshielded twisted-pai ...

  • Alloy RNS5 - page 20

     Technical Specifications Standards IEEE 802.3 10BaseT Ethernet IEEE 802.3u 100BaseT(X) Fast Ethernet IEEE802.3x Flow Control and Back pressure Protocols CSMA/CD Technology Store and Forward Transmission Rate 14,880 pps for Ethernet port 148,800 pps for Fast Ethernet port MAC address table size RNS5: 1K MAC address table RNS8: 2K MAC address tab ...

  • Alloy RNS5 - page 21

    Power Suppl y 12 to 48 VDC, redundant dual DC power inputs with reverse polarity protection, and a removable terminal block for master and slave VDC power inputs. Power consumption RNS5: 2.8 Watts RNS8: 4.6 Watts Packet throughput ability RNS5: 0.74Mpps @ 64bytes (5TX) RNS8: 1.19Mpps @ 64bytes (8TX) Installation DIN-Rail kit and wall mounting panel ...

  • Alloy RNS5 - page 22

    IEC60068-2-6 (Vibration) 20 ...

Fabbricante Alloy Categoria Switch

I documenti che otteniamo dal fabbricante del dispositivoAlloy RNS5 possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Alloy
- manuali per l’uso RNS5
- schede prodotto Alloy
- opuscoli
- o etichette energetiche Alloy RNS5
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Alloy RNS5.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Alloy RNS5, manuali di manutenzione, brevi manuali o manuali utente Alloy RNS5. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Alloy RNS5.

Manuali per l’uso simili

Manuale completo del dispositivo Alloy RNS5, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Alloy RNS5 dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Alloy RNS5.

Il manuale per l’uso completo Alloy, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Alloy RNS5 - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Alloy RNS5, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Alloy RNS5 che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Alloy RNS5 - che ci dovrebbe aiutare nei primi passi durante l'uso Alloy RNS5
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Alloy RNS5
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Alloy RNS5 in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Alloy RNS5?

Utilizza il modulo sottostante

Se non hai risolto il problema con Alloy RNS5 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Alloy RNS5 è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)