-
RCA RCU500 - page 1
RCU500 Universal Remote Control • • • TABLE OF CONTENTS Button Description ..............................................2 Setting Up Your Universal Remote ..................3 Programming Your Universal Remote Programming with Code Search ................4 Programming with Code Lists ...................5 Operating Your TV .................... ...
-
RCA RCU500 - page 2
Button Description • • • Code Search Button Programs devices by searching through brand codes. Use when code lists are not available or when the listed code does not work with your device. See page 4. Device Buttons ( VCR1, VCR2•LD, SAT•CABLE, AUDIO, TV) Determines which device you are controlling. The VCR2•LD and SAT•CABLE buttons ca ...
-
RCA RCU500 - page 3
3 Place Batteries in the remote 1. Remove the battery compartment cover. 2. Place 4 AAA batteries as shown, matching the + and – end of each battery as indicated in the battery compartment. 3. Replace the cover. Determine if your remote needs programming Some RCA, GE and ProScan devices may already be preprogrammed. 1. Press the button of the dev ...
-
RCA RCU500 - page 4
4 Programming a Device using CODE SEARCH 1. Manually turn on your device (TV, VCR, Laserdisc Player, Satellite Receiver, Cable Box or Audio Equipment). 2 . Press and hold CODE•SRCH . 3. Press and release the device button you want to set up (TV, VCR1, VCR2•LD, SAT•CABLE, or AUDIO) . 4. Release CODE•SRCH . 5. Press POWER repeatedly until the ...
-
RCA RCU500 - page 5
5 Programming Y our Universal Remote Programming a Device using CODE LISTS 1 . Find codes for each device and brand on page numbers shown below. Device Page TV 12 VCR 13 LaserDisc Player 14 Satellite Receiver 14 Cable Box 14 Audio Equipment 15 2. Press and hold the TV, VCR1, VCR2•LD , SAT•CABLE , or AUDIO button you want to set up. SAT•CABLE ...
-
RCA RCU500 - page 6
6 Turning the TV On and Off. 1. Press TV to set the remote to control the TV (Most RCA, GE and ProScan models will only turn on when TV is pressed, not POWER.) 2. Press POWER to turn the TV on or off. Change Channels on the TV Press CHANNEL UP or CHANNEL DOWN to change channels on the TV or enter the channels as you would normally for your TV. Use ...
-
RCA RCU500 - page 7
7 Turning the Cable Box On and Off. 1. Point the remote at the cable box and press SAT•CABLE. 2. Press POWER to turn it on or off. Changing Channels on the Cable Box. Press CHANNEL UP or DOWN to change channels on the cable box or enter the channel as you would normally for your cable box. 1. Point the remote at the Satellite Receiver, press SAT? ...
-
RCA RCU500 - page 8
Turn the VCR On and Off. 1. Press VCR1 or VCR2•LD to set the remote to control the VCR. (Most RCA, GE and ProScan models will only turn on when pressing VCR not POWER). 2. Press POWER to turn the VCR on or off. Using the VCR function buttons. 1. Turn on the VCR. 2. Insert a tape in the VCR. 3. Press PLAY to start the tape. 4. Press STOP when you ...
-
RCA RCU500 - page 9
9 Turn the Laserdisc Player On and Off. 1. Press VCR2•LD to set the remote to control the Laserdisc Player. 2. Press POWER to turn the Laserdisc Player on or off. Using the Laserdisc Player function buttons. 1. Turn on the Laserdisc Player. 2. Place a disc in the Laserdisc Player. 3. Press PLAY to start the disc. 4. Press STOP when you are finish ...
-
RCA RCU500 - page 10
10 RCA, GE, and ProScan televisions use three different menu systems. Read the following descriptions, and choose the one that matches your TV. System 1: If you use MENU, +, and – buttons on your current remote, substitute them with MENU•PROG, and the + and – (arrow) buttons on this remote, and refer to your TV owner’s manual for operating ...
-
RCA RCU500 - page 11
11 Operating Y our TV/VCR Combo Unit Special Operations RCA, GE and PROSCAN Brand Devices: Many of these devices (TVs and VCRs) will not need to be programmed. In the event that programming is required, the code search method is suggested. Note: With these brands, the device button (TV, VCR1, VCR2•LD, AUDIO) will usually turn the units on. The PO ...
-
RCA RCU500 - page 12
12 TV Code List A–Mark ................................................102 Admiral ................................................005 Amtron .................................................064 Akai ...............................................002,103 Anam ............................................104,105 Anam National ...................... ...
-
RCA RCU500 - page 13
13 VCR Code List Admiral .......................................006 Aiwa ............................................015 Akai ..........003,017,022,023,063,066 Audio Dynamics .................014,016 Bell & Howell .............................002 Broksonic ....................................010 Candle .............007,009,013,044,045 046,052 C ...
-
RCA RCU500 - page 14
14 Cable Box Code List TV/VCR Combinations ABC .........................022,046,053,054 Anvision ...............................007,008 Cablestar ..............................007,008 Diamond .....................................056 Eagle .....................................007,008 Eastern Int. ..................................002 General Instrum ...
-
RCA RCU500 - page 15
15 Audio Equipment Code List ADS AMP ......................................001 AIWA CD .........................................060 AKAI AMP ...............................002,008 DENON CD ........................................057 DYNAMIC BASS AM/FM ................................029 CD .........................................025 TAPE ......... ...
-
RCA RCU500 - page 16
W ORKS UP T O 5 VIDEO AND A UDIO COMPONENTS: More versatile than competitive models. Replace up to 5 remote controls...1 TV, 1 VCR, 1 VCR or Laser Disc Player, 1 Cable Box or Satellite Receiver and 1 Audio Component. Specially designed for home theatre. See the extensive brand list for coverage. CODE SEARCH: Makes set-up easy. Scans the entire code ...
Hai una domanda su RCA RCU500?
Utilizza il modulo sottostante
Se non hai risolto il problema con RCA RCU500 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con RCA RCU500 è probabile che voglia condividere il modo di risolverlo.