Italiano dropdown-ico

Manuale per l’uso Hoshizaki F-450MAH-C

51 pagine 1.01 mb
Scarica

Vai alla pagina of 51

Summary
  • Hoshizaki F-450MAH-C - page 1

    Hoshizaki “A Superior Degree of Reliability” www .hoshizaki.com Models F-450MAH(-C) Modular Flaker Hoshizaki America, Inc. Number: 73112 Issued: 8-21-2009 SER V I CE MA NU A L ® ...

  • Hoshizaki F-450MAH-C - page 2

    2 IMPOR T ANT Only qualified service technicians should install, service, and maintain the icemaker. No service or maintenance should be undertaken until the technician has thoroughly read this Service Manual. Failure to service and maintain the equipment in accordance with this manual may adversely affect safety, performance, component life, and w ...

  • Hoshizaki F-450MAH-C - page 3

    3 CONTENTS I. Specifications .............................................................................................................. ...... 4 1. F-450MAH .................................................................................................................... 4 2. F-450MAH- C ....................................................... ...

  • Hoshizaki F-450MAH-C - page 4

    4 AC SUPPLY VOLTAGE 115/60/1 COMPRESSOR 120 V 8.5 RLA 51 LRA GEAR MOTOR 120 V 1.6 FLA 1/6 HP FAN MOTOR 115 V 0.85FLA 50W OTHER 120 V 0.03A MAXIMUM FUSE SIZE 20 A MAX. HACR BREAKER (USA ONLY) 20 A MAX. CIRC. BREAKER (CANADA ONLY) 20 A MINIMUM CIRCUIT AMPACITY 20 A APPROXIMATE ICE PRODUCTION Ambient WATER TEMP. (°F) PER 24 HR. Temp.(°F) 50 70 90 lb ...

  • Hoshizaki F-450MAH-C - page 5

    5 AC SUPPLY VOLTAGE 115/60/1 COMPRESSOR 120 V 8.5 RLA 51 LRA GEAR MOTOR 120 V 1.6 FLA 1/6 HP FAN MOTOR 115 V 0.85FLA 50W OTHER 120 V 0.03A MAXIMUM FUSE SIZE 20 A MAX. HACR BREAKER (USA ONLY) 20 A MAX. CIRC. BREAKER (CANADA ONLY) 20 A MINIMUM CIRCUIT AMPACITY 20 A APPROXIMATE ICE PRODUCTION Ambient WATER TEMP. (°F) PER 24 HR. Temp.(°F) 50 70 90 lb ...

  • Hoshizaki F-450MAH-C - page 6

    6 II. General Information 1. Construction Water Supply Inlet Junction Box Condenser Fan Motor Compressor Drier Control Water Valve Bin Control Ice Chute Evaporator Flush Water Valve Control Box Gear Motor ...

  • Hoshizaki F-450MAH-C - page 7

    7 2. Control Bo x Lay out Note: The above component names are identical with the wiring label, but not with the parts list. ...

  • Hoshizaki F-450MAH-C - page 8

    8 3. Timer Board [a] Solid-State Control 1) A HOSHIZAKI exclusive solid-state control is employed in the self-contained flaker icemakers. 2) A printed circuit board (hereafter called “timer board”) includes a stable and high quality control system. 3) All models are pre-tested and factory-adjusted. [b] Timer Board CA UTION 1. Fragile, handle ve ...

  • Hoshizaki F-450MAH-C - page 9

    9 Fig. 1 [c] Sequence Fig. 2 ...

  • Hoshizaki F-450MAH-C - page 10

    10 Fig. 3 E D O C T R A P1 0 - 5 0 3 7 3 4 L E D O M1 0 C 4 4 1 A A 2 H G N I T A Rz H 0 6 / 0 5 C A V 4 2 1 T. c e s 5 1 ± 0 6 2 T. c e s 2 2 ± 0 9 3 T. c e s 5 4 ± 0 5 1 4 Ts s e l r o . c e s 1 5 T% 0 7 ± . c e s 7 . 6 6 T% 0 7 ± . c e s 7 . 6 ...

  • Hoshizaki F-450MAH-C - page 11

    11 Functions of Terminals 1) Terminals 1, 2 Power supply AC 24V. 2) Terminals 3, 4 Control X 1 (GM) and X 2 (CM) Relays. When closed, energize X 1 (GM) in 1 sec. and X 2 (CM) in 60 sec. When opened, de-energize X 1 (GM) in 150 sec. and X 2 (CM) in 90 sec. 3) Terminals 5, 6 Control X 1 (GM) and X 2 (CM) Relays. When opened, de-energize X 1 (GM) and ...

  • Hoshizaki F-450MAH-C - page 12

    12 III. T echnical Inf ormation 1. W ater Cir cuit and Refrigeration Circuit ...

  • Hoshizaki F-450MAH-C - page 13

    13 2. Wiring Dia gram [a] F-450MAH ...

  • Hoshizaki F-450MAH-C - page 14

    14 [b] F-450MAH-C ...

  • Hoshizaki F-450MAH-C - page 15

    15 3. Sequence of Electrical Circuit [a] When power switch is moved to “ON” position and flush switch to “ICE” position, water starts to be supplied to reservoir. ...

  • Hoshizaki F-450MAH-C - page 16

    16 [b] When reservoir has been filled, gear motor starts immediately. ...

  • Hoshizaki F-450MAH-C - page 17

    17 [c] Compressor starts about 60 sec. after gear motor starts. ...

  • Hoshizaki F-450MAH-C - page 18

    18 [d] Bin control operates, and about 6 sec. later, compressor and gear motor stop simultaneously. ...

  • Hoshizaki F-450MAH-C - page 19

    19 [e] Low water (except water-cooled model). ...

  • Hoshizaki F-450MAH-C - page 20

    20 [f] When flush switch is moved to “FLUSH” position, flush water valve opens and flushes reservoir and evaporator. ...

  • Hoshizaki F-450MAH-C - page 21

    21 [g] When flush timer operates (for 21 min. every 12 hours), flush water valve opens and flushes reservoir and evaporator. ...

  • Hoshizaki F-450MAH-C - page 22

    22 [h] When 208-230V are supplied to circuit protect relay, it protects the circuit from being miswired. If the power supply is properly connected, the contact of circuit protect relay does not move even when the coil is energized. ...

  • Hoshizaki F-450MAH-C - page 23

    23 [i] When pressure switch opens, power supply to the control board is cut off causing the compressor and gear motor to turn off immediately. ...

  • Hoshizaki F-450MAH-C - page 24

    24 [j] When input voltage is too low (less than 70%) gear motor fuse (1.5A) is blown causing compressor and gear motor to turn off immediately. ...

  • Hoshizaki F-450MAH-C - page 25

    25 Miswiring. Circuit Protect Relay operates. Proper wiring. The unit starts. BIN CONTROL OFF ON 1. CIRCUIT PROTECT RELA Y 2. W A TER LEVEL 3. FLOA T SWITCH UPPER LOWER 4. W A TER CONTROL RELA Y 5. CONTROL W A TER VA LV E 6. FLUSH TIMER 7. FLUSH SWITCH 8. FLUSH W A TER VA LV E 9. BIN CONTROL 10. GEAR MOTOR RELA Y 1 1. GEAR MOTOR 12. F AN MOTOR 13. ...

  • Hoshizaki F-450MAH-C - page 26

    26 1. CIRCUIT PROTECT RELA Y 2. W A TER LEVEL 3. FLOA T SWITCH UPPER LOWER 4. W A TER CONTROL RELA Y 5. CONTROL W A TER VA LV E 6. FLUSH TIMER 7. FLUSH SWITCH 8. FLUSH W A TER VA LV E 9. BIN CONTROL 10. GEAR MOTOR RELA Y 1 1. GEAR MOTOR 12. F AN MOTOR 14. PRESSURE SWITCH ON OFF ON OFF ON OFF ON OFF ON OFF 1 - 2 2 - 3 FLUSH ICE ON OFF ON OFF ON OFF ...

  • Hoshizaki F-450MAH-C - page 27

    27 1. CIRCUIT PROTECT RELA Y 2. W A TER LEVEL 3. FLOA T SWITCH UPPER LOWER 4. W A TER CONTROL RELA Y 5. CONTROL W A TER VA LV E 6. FLUSH TIMER 7. FLUSH SWITCH 8. FLUSH W A TER VA LV E 9. BIN CONTROL 10. GEAR MOTOR RELA Y 1 1. GEAR MOTOR 12. F AN MOTOR 14. PRESSURE SWITCH ON OFF ON OFF ON OFF ON OFF ON OFF 1 - 2 2 - 3 FLUSH ICE ON OFF ON OFF ON OFF ...

  • Hoshizaki F-450MAH-C - page 28

    28 APPROXIMATE Ambient ICE PRODUCTION Temp. (°F) PER 24 HR. 70 484 220 462 209 442 201 80 424 192 406 184 389 176 90 372 169 362 164 341 155 lbs./day kg/day 100 327 148 313 142 294 133 APPROXIMATE ELECTRIC 70 879 -- 885 -- 890 -- CONSUMPTION 80 896 -- 901 -- 907 -- 90 912 -- 918 -- 928 -- watts 100 937 -- 947 -- 956 -- APPROXIMATE WATER 70 0 0 58 ...

  • Hoshizaki F-450MAH-C - page 29

    29 APPROXIMATE Ambient ICE PRODUCTION Temp. (°F) PER 24 HR. 70 430 195 410 185 395 180 80 380 170 365 165 350 160 90 135 150 325 150 310 140 lbs./day kg/day 100 300 135 290 130 270 120 APPROXIMATE ELECTRIC 70 883 -- 891 -- 898 -- CONSUMPTION 80 906 -- 913 -- 921 -- 90 928 -- 936 -- 944 -- watts 100 953 -- 961 -- 964 -- APPROXIMATE WATER 70 52 195 ...

  • Hoshizaki F-450MAH-C - page 30

    30 IV . Service Diagnosis 1. No Ice Production PROBLEM POSSIBLE CAUSE REMEDY [1] The icemaker will not start. a) Power Supply 1. OFF position. 1. Move to ON position. 2. Loose connection. 2. Tighten. 3. Bad contacts. 3. Check for continuity and replace. 4. Blown fuse. 4. Replace. b) Power Switch (Control Box) 1. Off position. 1. Move to ON position ...

  • Hoshizaki F-450MAH-C - page 31

    31 PROBLEM POSSIBLE CAUSE REMEDY c) Gear Motor Relay 1. Coil winding opened. 1. Replace. 2. Bad contacts. 2. Check for continuity and replace. d) Control Timer (Printed Circuit Board) 1. Broken. 1. Replace. e) Gear Motor Protect Relay 1. Coil winding opened. 1. Replace. 2. Bad contacts. 2. Check for continuity and replace. [4] Water has been suppli ...

  • Hoshizaki F-450MAH-C - page 32

    32 PROBLEM POSSIBLE CAUSE REMEDY [7] Gear Motor and Compressor start but no ice is produced. a) Refrigerant Line 1. Gas leaks. 1. Check for leaks with a leak detector. Reweld leak, replace drier and charge with refrigerant. The amount of refrigerant is marked on Nameplate or Label. 2. Refrigerant line clogged. 2. Replace the clogged component. b) S ...

  • Hoshizaki F-450MAH-C - page 33

    33 2. Low Ice Production PROBLEM POSSIBLE CAUSE REMEDY [1] Low ice production a) Refrigerant Line 1. Gas leaks. 1. See "1. [5] a) Refrigerant Line." 2. Refrigerant line clogged. 2. Replace the clogged component. 3. Overcharged. 3. Recharge. b) High-side Pressure Too High 1. Dirty Air Filter or Condenser. 1. Clean. 2. Ambient temperature t ...

  • Hoshizaki F-450MAH-C - page 34

    34 3. Other PROBLEM POSSIBLE CAUSE REMEDY [1] Abnormal noise a) Fan Motor 1. Bearing worn out. 1. Replace. 2. Fan blade deformed. 2. Replace fan blade. 3. Fan blade does not move freely. 3. Replace. b) Compressor 1. Bearings worn out, or cylinder valve broken. 1. Replace. 2. Mounting pad out of position. 2. Reinstall. c) Refrigerant Lines 1. Rub or ...

  • Hoshizaki F-450MAH-C - page 35

    35 IMPORT ANT 1. The Polyol Ester (POE) oils used in R-404A units can absorb moisture quickly. Therefore it is important to prevent moisture from entering the system when replacing or servicing parts. 2. Always install a new filter drier every time the sealed refrigeration system is opened. 3. Do not leave the system open for longer than 15 minutes ...

  • Hoshizaki F-450MAH-C - page 36

    36 2. Brazing W ARNING 1. Refrigerant R-404A itself is not flammable at atmospheric pressure and temperatures up to 176°F. 2 . Refrigerant R-404A itself is not explosive or poisonous. However, when exposed to high temperatures (open flames) R-404A can be decomposed to form hydrofluoric acid and carbonyl fluoride both of which are hazardous. 3 . Al ...

  • Hoshizaki F-450MAH-C - page 37

    37 3. Removal and Replacement of Compressor IMPORT ANT Always install a new drier every time the sealed refrigeration system is opened. Do not replace the drier until after all other repair or replacement has been made. 1) Unplug the icemaker. 2) Remove the panels. 2) Remove the terminal cover on the compressor, and disconnect the compressor wiring ...

  • Hoshizaki F-450MAH-C - page 38

    38 13) Check for leaks using nitrogen gas (140 PSIG) and soap bubbles. 14) Evacuate the system, and charge it with refrigerant. See the nameplate for the required refrigerant charge and type. 15) Connect the terminals to the compressor, and replace the terminal cover in its correct position. 16) Replace the panels in their correct position. 17) Plu ...

  • Hoshizaki F-450MAH-C - page 39

    39 1) Unplug the icemaker. 2) Remove the panels. 3) Recover the refrigerant and store it in an approved container, if required by an applicable law. 4) Remove the expansion valve bulb at the evaporator outlet. 5) Remove the expansion valve cover, and remove the expansion valve using brazing equipment. 6) Braze the new expansion valve with nitrogen ...

  • Hoshizaki F-450MAH-C - page 40

    40 6. Removal and Replacement of Evaporator Assembly 1) Drain the water from the evaporator by switching the flush switch to “FLUSH” on the control box. 2) Unplug the icemaker. 3) Remove the panels. 4) Remove the three thumbscrews and take off the spout from the evaporator. Cutter 5) Loosen the cutter by a wrench and remove it. 6) Remove the cy ...

  • Hoshizaki F-450MAH-C - page 41

    41 11) Remove the bulb of the expansion valve. 12) Disconnect the brazing-connections of the expansion valve and the copper tube- low side from the evaporator, using brazing equipment. 13) Remove the two truss head machine screws and the bracket securing the evaporator. 14) Disconnect the three hoses from the evaporator. 15) Remove the four socket ...

  • Hoshizaki F-450MAH-C - page 42

    42 23) When replacing the evaporator: (a) Braze the new evaporator with nitrogen gas flowing at the pressure of 3-4 PSIG. (b) Replace the drier. (c) Check for leaks using nitrogen gas (140 PSIG) and soap bubbles. (d) Evacuate the system. Charge it with refrigerant. See the nameplate for required refrigerant charge and type. 24) Replace the panels i ...

  • Hoshizaki F-450MAH-C - page 43

    43 6) Remove the water supply hose from the control water valve. 7) Install the new control water valve. 8) Assemble the removed parts in the reverse order of the above procedure. 9) Open the water supply line shut-off valve. 10) Check for water leaks. 11) Replace the panels in their correct position. 12) Plug in the icemaker. 9. Remov al and Repla ...

  • Hoshizaki F-450MAH-C - page 44

    44 14) Move the flush switch to the “ICE” position. 15) Check for water leaks. 16) Move the flush switch to the “FLUSH” position, and make sure water is flushing. 17) Move the flush switch to the “ICE” position. 18) Replace the panels in their correct position. VI. Cleaning and Maintenance IMPORT ANT Ensure all components, fasteners and ...

  • Hoshizaki F-450MAH-C - page 45

    45 2. Cleaning and Sanitizing Instructions W ARNING 1. HOSHIZAKI recommends cleaning this unit at least once a year. More frequent cleaning, however, may be required in some existing water conditions. 2. To prevent injury to individuals and damage to the icemaker, do not use ammonia type cleaners. 3. Always wear liquid-proof gloves to prevent the c ...

  • Hoshizaki F-450MAH-C - page 46

    46 [b] Cleaning Procedure The cleaning process will remove lime deposits from the water system. 1) Remove the front panel and top panel, then turn off the power supply. 2) Close the water supply line shut-off valve. 3) Remove all ice from the storage bin. 4) Move the flush switch to the “FLUSH” position. 5) Turn on the power supply and drain ou ...

  • Hoshizaki F-450MAH-C - page 47

    47 [c] Sanitizing Solution Dilute 2.5 fl. oz. (74 ml or 5 tbs) of IMS-II Sanitizer or a 5.25% sodium hypochlorite solution (chlorine bleach) with 5 gallons (19 l) of warm water. IMPOR T ANT For safety and maximum effectiveness, use the solution immediately after dilution. [d] Sanitizing Procedure - Initial The sanitizing process will sanitize the i ...

  • Hoshizaki F-450MAH-C - page 48

    48 14) Replace all parts in their correct positions. IMPOR T ANT When installing the baffles, make sure that the bent surface (the one without the studs) faces the actuator so that the bent surface can guide the ice to the center of the actuator. 15) Move the flush switch to the “ICE” position, then turn on the power supply. Replace the top pan ...

  • Hoshizaki F-450MAH-C - page 49

    49 16) When the gear motor starts, remove the front panel and turn off the power supply. 17) Drain out all water from the water line. See 2) and 3). 18) Move the flush switch to the “ICE” position and run the icemaker. 19) Turn off the power supply after 30 minutes. 20) Pour warm water into the storage bin to melt all ice, and then clean the bi ...

  • Hoshizaki F-450MAH-C - page 50

    50 3. Maintenance Instructions IMPOR T ANT 1. This icemaker must be maintained individually, referring to the instruction manual and labels provided with the icemaker. 2. To have the optimum performance of this icemaker, the following consumable parts need periodic inspection, maintenance and replacement: Extruding Head Housing Gear Motor Auger Mec ...

  • Hoshizaki F-450MAH-C - page 51

    51 3) Air Filter A plastic mesh air filter removes dirt or dust from the air, and keeps the condenser from getting clogged. As the filter gets clogged, the icemaker’s performance will be reduced. Check the filter at least twice a month. When clogged, use warm water and a neutral cleaner to wash the filter. 4) Condenser Check the condenser once a ...

Fabbricante Hoshizaki Categoria Refrigerator

I documenti che otteniamo dal fabbricante del dispositivoHoshizaki F-450MAH-C possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Hoshizaki
- manuali per l’uso F-450MAH-C
- schede prodotto Hoshizaki
- opuscoli
- o etichette energetiche Hoshizaki F-450MAH-C
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Hoshizaki F-450MAH-C.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Hoshizaki F-450MAH-C, manuali di manutenzione, brevi manuali o manuali utente Hoshizaki F-450MAH-C. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Hoshizaki F-450MAH-C.

Manuali per l’uso simili

Manuale completo del dispositivo Hoshizaki F-450MAH-C, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Hoshizaki F-450MAH-C dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Hoshizaki F-450MAH-C.

Il manuale per l’uso completo Hoshizaki, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Hoshizaki F-450MAH-C - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Hoshizaki F-450MAH-C, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Hoshizaki F-450MAH-C che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Hoshizaki F-450MAH-C - che ci dovrebbe aiutare nei primi passi durante l'uso Hoshizaki F-450MAH-C
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Hoshizaki F-450MAH-C
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Hoshizaki F-450MAH-C in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Hoshizaki F-450MAH-C?

Utilizza il modulo sottostante

Se non hai risolto il problema con Hoshizaki F-450MAH-C con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Hoshizaki F-450MAH-C è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)