-
Ryobi SA1802 - page 1
OPERA T OR'S MANU AL CORDLESS DRILL-DRIVER MODEL NOS. SA1202 / SA14402 / SA1802 This new drill has been engineered and manufactured to our Ryobi’s high standard for dependability, ease of operation, and operator safety. When properly cared for, the drill will give you years of rugged, trouble-free performance. W ARNING: T o reduce the risk o ...
-
Ryobi SA1802 - page 2
Page 2 ■ ■ ■ ■ ■ Introduction .................................................................................................................................................................... 2 ■ ■ ■ ■ ■ General Saf ety Rules ..................................................................................................... ...
-
Ryobi SA1802 - page 3
Page 3 GENERAL SAFETY R ULES W ARNING: Read and understand all instructions. F ailure to f ollow all instructions listed below , may result in elec- tric shock, fire and/or serious personal injur y . SA VE THESE INSTR UCTIONS WORK AREA ■ Keep y our w ork area c lean and well lit . Cluttered benches and dark areas invite accidents . ■ Do not ope ...
-
Ryobi SA1802 - page 4
Page 4 GENERAL SAFETY R ULES SPECIFIC SAFETY R ULES SER VICE ■ T ool service must be performed only b y qualified repair personnel. Ser vice or maintenance performed by unqualified personnel ma y result in a r isk of injury . ■ When servicing a tool, use onl y identical replace- ment parts. Follo w instructions in the Maintenance section of thi ...
-
Ryobi SA1802 - page 5
Page 5 IMPOR T ANT SAFETY INSTRUCTIONS FOR CHARGER W ARNING: Read and understand all instructions. F ailure to f ollow all instructions listed below , may result in elec- tric shock, fire and/or serious personal injur y . ■ Never use a battery that has been dropped or received a sharp blow. A damaged battery is subject to explosion. Properly disp ...
-
Ryobi SA1802 - page 6
Page 6 The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and the explanations with them, deserve your careful attention and understanding. The safety warnings do not by themselves eliminate any danger. The instructions or warnings they give are not substitutes for proper accident prevention measures ...
-
Ryobi SA1802 - page 7
Page 7 INSTRUCTIONS When unpacking the tool: ■ Carefully remov e the tool and accessor ies from the box. ■ Make sure that all items listed in the pac king list are in- cluded. ■ Inspect the tool carefully to make sure no breakage or damage occurred during shipping. ■ Do not discard the packing material until you ha ve care- fully inspected ...
-
Ryobi SA1802 - page 8
Page 8 KNOW YOUR DRILL-DRIVER See Figure 1. Before using this tool, familiarize yourself with all operating features and safety requirements. However, do not let familiarity with the tool make you careless. This new drill-driver is equipped with the following features. KEYLESS CHUCK The drill-dr i v er has a k e yless chuc k that allo ws y ou to ha ...
-
Ryobi SA1802 - page 9
Page 9 24 20 5 FEA TURES Fig. 1 KEYLESS CHUCK BIT ST ORAGE AREA TORQUE ADJUSTMENT RING SWITCH TRIGGER LEVEL BA TTER Y P ACK DIRECTION OF ROT A TION SELECT OR TWO SPEED GEAR TRAIN (HI-LO) MAG TRA Y ™ (SCREW HOLDER) TOP VIEW OF LEVEL FOR HORIZONT AL DRILLING END VIEW OF LEVEL FOR VERTICAL DRILLING ...
-
Ryobi SA1802 - page 10
Page 10 REVERSIBLE See Figure 2. This tool is reversible. The direction of rotation is controlled by a selector located above the switch trigger. With the drill held in normal operating position, the direction of rotation selector should be positioned to the left of the switch for drilling. The drilling direction is reversed when the selector is to ...
-
Ryobi SA1802 - page 11
Page 11 ADJUSTMENTS INSTALLING BITS See Figures 4 and 5. ■ Place the direction of rotation selector in center position. This will lock the switch trigger in the off position. See Figure 10. ■ Open or close the chuck jaws to a point where the opening is slightly larger than the bit size you intend to use. Also, raise the front of your drill slig ...
-
Ryobi SA1802 - page 12
Page 12 24 20 5 24 20 5 ADJUSTMENTS ADJUSTABLE TORQUE CLUTCH See Figure 6. When using your drill-driver f or va rious driving applications, it becomes necessar y to increase or decrease the torque in order to help prev ent the possibility of damaging screw heads, threads, w orkpiece, etc. In general, torque should correspond to the intensity of the ...
-
Ryobi SA1802 - page 13
Page 13 OPERA TION Fig. 8 W ARNING: Do not allow f amiliarity with the dr ill-driver to mak e you careless . Remember that a careless fraction of a second can result in a serious personal injur y . LED FUNCTION OF CHARGER See Figure 8. LED WILL BE LIGHTED T O INDICA TE ST A TUS OF CHARGER AND B A TTER Y P ACK: ■ Red LED lighted = F ast Charging M ...
-
Ryobi SA1802 - page 14
Page 14 24 20 5 IMPORTANT INFORMATION FOR RECHARGING HOT BATTERIES When using your drill-driver continuously, the batteries in your battery pack become hot. You should let a hot battery pack cool down for approximately 30 minutes before at- tempting to recharge. Note: This situation occurs when continuous use of your drill-driver causes the batteri ...
-
Ryobi SA1802 - page 15
Page 15 OPERA TION W ARNING: Always wear safety goggles or safety glasses with side shields when operating tool. Failure to do so could result in objects being thrown into your eyes, resulting in possible serious injury. DRILLING See Figure 12. When drilling hard, smooth surfaces, use a center punch to mark the desired hole location. This will prev ...
-
Ryobi SA1802 - page 16
Page 16 OPERA TION LEVEL DRILLING See Figures 12 and 13. A conv enient new feature pro vided with your drill is a lev el. It is recessed in the motor housing on top of your drill. It can be used to keep drill bit le v el dur ing drilling operations. W ARNING: Do not force tool. F orcing tool can result in jamming and loss of balance or f ooting, wh ...
-
Ryobi SA1802 - page 17
Page 17 MAINTENANCE Fig. 16 Fig. 15 Fig. 17 24 20 5 24 20 5 24 20 5 MALLET CHUCK JA WS KEYLESS CHUCK HEX KEY WRENCH W ARNING: When ser vicing use only identical Ry obi replacement par ts. Use of any other par ts ma y create a hazard or cause product damage. Do not abuse po wer tools . Abusiv e practices can damage tool as well as workpiece. W ARNIN ...
-
Ryobi SA1802 - page 18
Page 18 R E C Y C L E 1 . 8 0 0 . 8 2 2 . 8 8 3 7 RBRC Ni Cd ™ MAINTENANCE To obtain the longest possible battery life, we suggest the following: ■ Store and charge your batteries in a cool area. Temperatures below 50°F or above 100°F will shorten battery life. ■ Never store batteries in a discharged condition. Recharge them immediately aft ...
-
Ryobi SA1802 - page 19
Page 19 NO TES ...
-
Ryobi SA1802 - page 20
983000-334 6-03 • SER VICE Now that you have purchased your tool, should a need ever exist for repair parts or service, simply contact your nearest Ryobi Authorized Service Center. Be sure to provide all pertinent facts when you call or visit. Please call 1-800-525-2579 for your nearest Ryobi Authorized Service Center. You can also check our web ...
Hai una domanda su Ryobi SA1802?
Utilizza il modulo sottostante
Se non hai risolto il problema con Ryobi SA1802 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Ryobi SA1802 è probabile che voglia condividere il modo di risolverlo.