-
Smeg WDF16BA1 - page 1
1 WASHER DRYER INSTRUCTIONS MANUAL GB ...
-
Smeg WDF16BA1 - page 2
2 GB Contents 1. The new washing system 3 2. Safety warnings 4 3. Installation inst ructions 7 4. Description of cont rols 9 5. Washing instructions 13 6. Drying instructions 19 7. Cleaning and maintena nce 21 8. Troubleshooting 23 9. Control panel symbols 25 This appliance is marked according to the Eu ropean directive 2002/96/EC on W aste Electri ...
-
Smeg WDF16BA1 - page 3
GB 3 1. THE NEW WA SHING SYSTEM This new washer dryer is th e outcome of years of research . The leading-edge design and the quality of the p roduction processes used to manufacture this p roduct ensure it will give you many years of excellen t service. Its concept satisfie s all current and future washing an d drying requirements. Its low water, p ...
-
Smeg WDF16BA1 - page 4
GB 4 2. S A FETY WAR NINGS Attention! These w arnings are giv en for safety reasons. Please read them caref ully before installing a nd using the appliance. This m anual f orms an integ ral part of the appliance an d m us t ther efore be k ept in tact together with the machine. Before us ing the appliance , c arefull y rea d all t he i nstructions ...
-
Smeg WDF16BA1 - page 5
GB 5 Do not wash petro l-soak ed garm ents in the was her dr yer. Make sure t here are no i nflamm able item s (e.g.: lighters, m atches , etc.) in pock ets befor e washing. If volatile flu ids have b een us ed to clean garm ents, make s ure that the su bstances have been r emoved before load ing them in th e washing m achine. Before loadin g garm ...
-
Smeg WDF16BA1 - page 6
GB 6 For Great Britain only Warning : th is appliance m ust be ear thed. Fuse replacem ent If the m ains lead of this a ppliance is fitted with a BS 1363 A 13amp fused p lug, to chan ge a fus e in this t ype of plug use an A.S.T. A . appro ved f use to BS 1362 t ype and procee d as f ollows: 1. Remove the fus e cover ( A ) and fus e ( B ) 2. Fit re ...
-
Smeg WDF16BA1 - page 7
GB 7 3. INSTALLA TION INSTRUCTIONS Important ! The appliance must be ins talled by a special ised technician according to curre nt regulations. This washer dr y er is ver y heav y. Take care when lifting it. 3.1 UNPACK ING The ins ide of the mac hine comprises a mo ving assembly which is blocked fo r transport p urposes by the screws ( A) located a ...
-
Smeg WDF16BA1 - page 8
GB 8 3.3 WATER SUPPLY CONNECTION 1. Check t hat inlet pressure li es between the following values: 50-900kPa . For higher pressures, install a pressure reducer. 2. Connect the c old w ater inlet hose ( light blue ring nut) to the c old water tap with a ¾ gas thread, taking ca re to sc rew it fi rmly into place in order to prevent leaks . The water ...
-
Smeg WDF16BA1 - page 9
GB 9 4. DESCRIPTION OF CONTROLS 4.1 CONTROL PA NEL All the commands and con trols of the appliance are assembled together on the f ront panel. Description of contro ls A Open doo r button B ON-O FF and pro gramme selection k nob C Delay t imer show n on displa y LED – (on ly for mod els w ith this o ption) D T ime remaining sho wn on displ ay LED ...
-
Smeg WDF16BA1 - page 10
GB 10 A Open door button Press the button to op en the d oor . Chapter 5 – Washing instructions – explains ho w the door works and h ow to use it. B ON-OFF and washing and drying programme selection knob This knob lets you: • switch the m achine o n and off b y m oving it in either direction from the OFF position (k nob indicator vertical) ? ...
-
Smeg WDF16BA1 - page 11
GB 11 I Select spin speed and drying time for delicate s button Press the button repeate dly to select the require d spin speed. The f ollowing spin speeds are a vailable: • 0000: spin d isabled and stop with tub full. T he machine does not p erform the final sp in and ends the washing pro gramm e with water in th e tub. T o drain the water, see ...
-
Smeg WDF16BA1 - page 12
GB 12 Economy cycle button - e Press this button for cottons programmes, the machine will perform an e xtended wash at 35°C (biological step) thereby offering good washing p erformance combined w ith power saving. The m achine then continues the cy cle at the selected temperature. N.B.: Press the eco nomy c y cle button to o btain a maximum w ashi ...
-
Smeg WDF16BA1 - page 13
GB 13 4.2 DETERGENT TRAY This is located to the left of the control panel. Pull it out to open. The tray com prises four com partments which are mark ed as follows “ 1” : pre-wash d etergent “2” : main wash deterge nt “ ” or “3” : f abric softener, s tarch, etc. (tr eatment pro ducts ). Compar tment “4” is used f or bleach. If t ...
-
Smeg WDF16BA1 - page 14
GB 14 5.2 OPENING TH E DOOR The machine is fitted with a safety device that prevents the door from o pening while it is working. 1. Before opening the door, w ait 1 or 2 minu tes after the programm e ends (“End” LED on) to allo w the safety device to disengage. 2. Make sure there is no w ater in the tu b and that the drum is not moving. Open th ...
-
Smeg WDF16BA1 - page 15
GB 15 Water hardness Hardness lev el French degree f H German degree dH Soft Up to 15° Up to 8° Moderatel y hard 15° - 25° 8° - 14° Hard 25° - 40° 14° - 22° Very hard Over 40° Over 22° 5.6 DOSING POWDER DETERGENT S Normally dirty washing 1. Choose a programme without prewash. 2. Pour the total quantity of dete rgent indicated on the pac ...
-
Smeg WDF16BA1 - page 16
GB 16 Intensive w ashing p rogramme for resistant cotton , coloured or hemp fabrics. Delicate w ashing progra mmes for delicate artificial synthe tic fibres , blends or linen fabrics. They prevent the formation o f creases that are difficult to remove du ring ironing. Wool prog ramme only for garments marked “p ure wool ” washable, treated, shr ...
-
Smeg WDF16BA1 - page 17
GB 17 5.10.3 DELAYED START ( ONLY FOR MODELS FEATURING THIS FUNCTION ) Press the delayed start button ( ). The relative LED located above the button lights up . The displ ay visualises the time re maining (hou rs/minutes) before the selected washing programme starts: the display ini tially shows 0 hours 0 minutes for all programmes. Press the butto ...
-
Smeg WDF16BA1 - page 18
GB 18 5.13 END OF PROGRA MME The wash ing programmes are automa tically completed , the display shows END and the “Time remaining” LED lights up. 1. Turn the programmes k nob to OFF to switch off the machine. 2. Open the door. 3. Remove the washing from the drum . 4. Leave the door ajar in ord er to allow the inside of the washer dryer to d ry. ...
-
Smeg WDF16BA1 - page 19
GB 19 6. USING THE MACH INE FOR DRYING PURPOSES 6.1 GENERA L INFORMATION During drying cycles it is essential that the water tap is open and that th e drain hose is correctly positioned. W ith this machine it is possible to set wash-only programmes, dry-only programmes and wash-dry programmes. For the latter pr ogrammes, the cyc le shifts automatic ...
-
Smeg WDF16BA1 - page 20
GB 20 6.3 TIMED DRYING The length of drying tim e corresponds to the time selected with the drying selec tion button. 6.4 WASH-DR Y PROGRA MME It is possible to us e a wash-d ry programme for inte nsive programmes (cotton, coloureds) and for synthetics/delicates. W ith the w ool wash pr ogramme it is not possible to select automatic drying after wa ...
-
Smeg WDF16BA1 - page 21
GB 21 7. CLEANING A ND M A INTENANCE Important – Before cleaning or servicing the machine, remove the plug from t he socket. 7.1 EXTERNA L CLEANING • Regular and constant cleani ng w ill ke ep your appliance looking like new. • Clean the outer surfaces with soap an d water and then dry thoroughly with a soft cloth. • Clean parts in plastic ...
-
Smeg WDF16BA1 - page 22
GB 22 3. Pull out the drain hose “A”. Attention: if the hose is hot it mea ns the water is hot o r boiling. Place a tray on the floor and remo ve the plug “B” to drain the water. Depending on the quantity of water, it ma y be necessary to e mpty the tray several times. W hen no more water comes out, push th e hose back in an d screw back th ...
-
Smeg WDF16BA1 - page 23
GB 23 8. TROUBLESHOOT ING This product complies w ith current safety regulations governing electrical equipment. For safety reas ons, all technical inspections or repairs must b e perfo rmed b y qualified technicians i n o rder to prevent h azardous situations for users. If the machi ne d oes not work, befo re calling the Ser vice Centre and s pend ...
-
Smeg WDF16BA1 - page 24
GB 24 11 The machine does not spin The unb alanced load sensor h as triggered because the washing is not uniformly dis tributed inside the drum. If the washing is wet at the end o f the cycle, distribute it well i nside the basket and repeat just the spin cycle. 12 Draining water from the drum In th e event of a power failure or a fault in the appl ...
-
Smeg WDF16BA1 - page 25
GB 25 9. CONTROL PA NEL SYMBOLS PROGRAMS OPTIONS OTHER SYMBOLS DRYING WATER INCREASE FABRIC CONDITIONER HAND WASH NO SPIN OR STOP WHIT FULL TUB OPEN DOOR PRE-WASH DELAY TIMER START-PAUSE RINSES DELICATES START DRAIN AND SPIN - e ECONOMY CYCLE WASH SECTION QUICK WASH END COTTON AND COLOURED EXTRA RINSE HEATING WOOL SPIN TIME REMAINING DRYING EASY-IR ...
Hai una domanda su Smeg WDF16BA1?
Utilizza il modulo sottostante
Se non hai risolto il problema con Smeg WDF16BA1 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Smeg WDF16BA1 è probabile che voglia condividere il modo di risolverlo.