Italiano dropdown-ico

Manuale per l’uso Pelco c2462m-e

24 pagine 1.09 mb
Scarica

Vai alla pagina of 24

Summary
  • Pelco c2462m-e - page 1

    INST ALLA TION C2462M-E (3/09) 090 Series Camclosure ® Indoor Integrated Camera System Surface Mount/In-Ceiling ...

  • Pelco c2462m-e - page 2

    2 C2462M-E (3/09) Contents Important Safety Instructi ons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Descripti ...

  • Pelco c2462m-e - page 3

    C2462M-E (3/09) 3 List of Illustrations 1 Removing the Dome Bubble . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 2 Ceiling/W all In stallation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 3 Concrete Ceilin ...

  • Pelco c2462m-e - page 4

    4 C2462M-E (3/09) Important Safety Instructions 1. Installation and servicing should be d one only by qualified service personnel and conform to all local codes. 2. Unless the unit is specifically marked as a NEMA T ype 3, 3R, 3S, 4, 4X, 6, or 6P enclosure, it is designed for indoor use only and must not be installed where exposed to rain and moist ...

  • Pelco c2462m-e - page 5

    C2462M-E (3/0 9) 5 Description The ICS090 Series Camclosure ® integrated camera system integrates a camera and lens package in a small, discreet dome. The system is easy to install and can be mounted or recessed to the surface of a ceiling or wall. Prior to the installation of your n ew system, thoroughly familiarize yourself with the information ...

  • Pelco c2462m-e - page 6

    6 C2462M-E (3/09) Remove the Dome Bubble T urn the dome bubble counterclockwise and lift (refer to Figure 1 ). Place the bubble on a non abrasive surface. Figure 1. Removing the Dome Bubb le If the unit is supplied with a dome liner , remove the li n er before installing the unit. T o remove the liner , gently lift it from the unit. Place t he line ...

  • Pelco c2462m-e - page 7

    C2462M-E (3/0 9) 7 Installation The installation methods for the ICS090 Series include the following options: • Mount to the surface of a ceiling or wall • Install in a suspended ceiling • Install in a fixed ceiling or wall • Mount to the surface of a 4S standard electrical bo x • Install in a 4S deep electrica l box SURFACE INSTALLATION: ...

  • Pelco c2462m-e - page 8

    8 C2462M-E (3/09) 4. Use 6-32 toggle bolts (not supplied) to attach the surface mount ring and back box to the mounting surface (refer to Figure 2 ). Figure 3. Concrete Ceiling/W all Installation Figure 2. Ceiling/Wall Installati on NOTE: For a concrete ceiling or wall installation, use 8-32 mounting hardware (not supplied), ref er to Figure 3. ...

  • Pelco c2462m-e - page 9

    C2462M-E (3/0 9) 9 IN-CEILING INSTALLATION: SUSPENDED CEILING 1. Remove the ceiling tile from the ceiling (refer to Figure 4 ). 2. Cut a 4-inch diameter h ole in the ceiling tile. 3. Remove the surface mount ring from the back box (refer to Figure 5 on page 10 ): a. Place your fingers on the circular marks loca ted on the s ides of the surface moun ...

  • Pelco c2462m-e - page 10

    Figure 5. How to Remove Surfac e Mount Ring from Back Box 10 C2462M-E (3/09) AC operation only: If you are wiring more than one Camclosure to the same transformer , connect one side of the transformer to the red wire on all uni ts; connect the other side of the transformer to the black wire on all units. NOTE: Failure to connect all of the units in ...

  • Pelco c2462m-e - page 11

    C2462M-E (3/0 9) 11 IN-CEILING INSTALLATION: FIXED CEILING OR WALL 1. Cut a 4-inch diameter h ole in the ceiling/wall (refer to Figure 6 on p age 11 ). 2. Remove the surface mount ring from the back box (refer to Figure 5 on page 10 ). a. Place your fingers on the circular marks loca ted on the s ides of the surface mount ring. b. Pinch the sides. ...

  • Pelco c2462m-e - page 12

    12 C2462M-E (3/09) SURFACE INSTALLATION: 4S STANDARD ELECTRICAL BOX 1. Attach the adapter ring to the 4S box with tw o 8-32 x 1.00-inch screws (supplied; refer to Figure 7 ). 2. Connect the video cable and wires. BNC: Connect the BNC connector from the Camclosure to a mating BNC connector . T wisted pair: Connect the blue wire to Video +; c onnect ...

  • Pelco c2462m-e - page 13

    C2462M-E (3/0 9) 13 IN-CEILING INSTALLATION: 4S DEEP ELECTRICAL BOX 1. Remove the surface mount ring from the back box (refer to Figure 8 ): a. Place your fingers on the circular marks loca ted on the s ides of the surface mount ring. b. Pinch the sides. c. Lift and remove the surface mount ring from the back box. 2. Attach the adapter ring to the ...

  • Pelco c2462m-e - page 14

    14 C2462M-E (3/09) Camera Positioning Figure 9. Positioning the Camera Manually rotate and tilt the came ra module to position th e camera. Do not over-rot ate the module. WAR NI NG : E xcessively turning the module in one direct ion could result in damage to the wiring.    ì T ilt 140° (20° to 160°) î Pan 360° ï Rotation 360° ...

  • Pelco c2462m-e - page 15

    C2462M-E (3/0 9) 15 Camera Adjustments SWITCH SETTINGS FIXED FOCAL LENGTH LENS WITHOUT AUTO IRIS Refer to the switch drawing. The switch is located n ext to the lens. Automatic backlight compensation (factory setting) is used under va ry ing lighting conditions (suc h as ou tdoors) or fixed lighting con ditions where there are no bright spots that ...

  • Pelco c2462m-e - page 16

    16 C2462M-E (3/09) FOCUS ADJUSTMENT NOTE: Y o u will need a miniature Phillips or flat-tip screw driver to loosen and tighten the locking screw. T o adjust the fo cus: 1. Loosen the focus locking screw . 2. Position the inverted dome appro ximately 0.125 inch (3.175 mm) from the front of the lens. Make sure that the len s and the dome are centered ...

  • Pelco c2462m-e - page 17

    C2462M-E (3/0 9) 17 V ERTICAL PHASE ADJUSTMENT (24 V ac Operation Only) When using more than one camera power supply, a brief vertical roll may occur on the monitor when a camera view is switched. T o elim inate vertica l roll, reverse the 24 V AC connections on one camera. If both cameras are connected to the same transformer , this should solve t ...

  • Pelco c2462m-e - page 18

    18 C2462M-E (3/09) Install Liner and Bubble DOME LINER INSTALLATION If the unit is supplied with a dome liner , reinstall th e liner be fore installing the dome bubble (refer to Figure 13 ): 1. Align the studs located on the camera module with the clips on the liner . 2. Lightly pinch the sides of the liner , opposite fro m the clips, and place the ...

  • Pelco c2462m-e - page 19

    C2462M-E (3/0 9) 19 DOME BUBBLE INSTALLATION T o install the d ome bubble (refer to Figure 14 ): 1. Select the bubble (clear or smoked). 2. Align the standoffs of the bubble with the slots of the back box. Figure 14. Installing the Dome Bubble 3. T urn the bubble clockwise until it locks in place. ...

  • Pelco c2462m-e - page 20

    20 C2462M-E (3/09) Service Connector An optional 4-foot service/monitor cable, part numb er ICS090-SC, is available for on- site setup and adjustments. T o use the cable, simply plug one end of the cable directly into the service connector of the ICS090, and then connect the other end to any st andard BNC (VIDEO IN) connector on a monitor . T o ass ...

  • Pelco c2462m-e - page 21

    C2462M-E (3/09) 21 Specifications ELECTRICAL Input V oltage* 12 VDC or 24 V AC (±10%), autosensing Power Consumption 3 W or less Video Connector BNC *24 V AC power is recommended when installing any Camclosure integrated camera system under fluorescent lighting conditions. GENERAL Pan/T ilt Adjustment Pan 360° T ilt 140° (20° to 160° range) Ro ...

  • Pelco c2462m-e - page 22

    22 C2462M-E (3/09) REVISION HISTORY Manual # Date Comments C2462M 11/02 Original version. C2462M-A 1/03 Added Regulatory Noti ces for FCC Class B. C2462M-B 10/05 Revised switch-set ting descript ions for vari focal lens. Adde d WEEE statement. C2462M-C 1/06 Updated factory sw itch setting s for varifo cal lens per ECO 13164. Updated w iring informa ...

  • Pelco c2462m-e - page 23

    The materials us ed in the manufactu re of this documen t and its component s are compliant to th e requirement s of Directive 20 02/95/EC. This equipment co ntains electr ical or electron ic components t hat must be rec ycled properly to comply with Dir ective 2002/96/EC of the European Union re garding the disp osal of waste electrical and elec t ...

  • Pelco c2462m-e - page 24

    Pelco, Inc. W orldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada T el (800) 289-9100 Fax (800) 289-9150 International T el +1 (559) 292-1981 Fax +1 (559) 348-1120 www .pelco.com ...

Fabbricante Pelco Categoria Camera Accessories

I documenti che otteniamo dal fabbricante del dispositivoPelco c2462m-e possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Pelco
- manuali per l’uso c2462m-e
- schede prodotto Pelco
- opuscoli
- o etichette energetiche Pelco c2462m-e
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Pelco c2462m-e.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Pelco c2462m-e, manuali di manutenzione, brevi manuali o manuali utente Pelco c2462m-e. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Pelco c2462m-e.

Manuali per l’uso simili

Manuale completo del dispositivo Pelco c2462m-e, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Pelco c2462m-e dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Pelco c2462m-e.

Il manuale per l’uso completo Pelco, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Pelco c2462m-e - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Pelco c2462m-e, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Pelco c2462m-e che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Pelco c2462m-e - che ci dovrebbe aiutare nei primi passi durante l'uso Pelco c2462m-e
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Pelco c2462m-e
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Pelco c2462m-e in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Pelco c2462m-e?

Utilizza il modulo sottostante

Se non hai risolto il problema con Pelco c2462m-e con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Pelco c2462m-e è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)